Can you put more info on the accessory switch panel your talking about? I want to do the same on my taco and don't want all these wires running to the battery. Thank you! Your truck is coming out bad ass! Love it!
@@GearheadJT I have the sPod bantam with Touchscreen and will be connecting the same light bar. I plan run the amber and white lights independently. Plus I'd like to connect the amber into the running lights but have to figure out how to do that.
There are two ways you can wire your dual function bar depending on how you would like it to operate. If you want to control the amber and white separately, then you will need 2 harnesses. With the 2 harnesses, this gives you the ability to run the Amber/White lights individually or all at the same time. The LED bar will have 3 wires on it. BLACK, WHITE, GREEN BLACK: Ground WHITE: Power For The White LED's GREEN: Power For The Amber LED's The harness will have DT Plugs at the end. You will want to remove those plugs as they are not needed. After the plugs are removed there will be red and black wires exposed. between both harnesses, you will have 2 red wires and 2 black wires. You will want to connect the 2 black wires together and connect them to the black wire on the LED bar, Then one red to the white and the other red to green. That will give you the ability to run the lights independently. If you are just wanting the full bar to turn on/off at once and not be able to control separately then you would just need one harness. Remove the plug from the harness. Connect the black wire from the LED bar to the black wire on the harness. Then combine the green and white wire on the LED bar to connect to the red on the harness.
I bought same set up. Watched this video and your squadron install. Id love to see how you actually wired those lights to that Cali raised switch system. Did you use relays? Or can you eliminate those with switch system?
I just installed mine today on a Prinsu and the same light that failed on yours flickered and then went out on mine. Did you get a replacement or repair this one?
I have a 40inch Clear Cali light bar slim on my prinsu for over a year and so far so good.been looking at this dual function but I hear there has been issues with them
I just ordered the same 43" LED and generic switch panel from your other video but am not sure what cable I need to order to run the ambers and white separately to different switches. My LED came with a very short cable running out of the drivers side. What cable do I need to get to hook the LED up to the switch panel? Any info would be appreciated going to do a self instal watching your switch panel instal video! Thanks
I’m about to install this bar on my Southern style offroad rack. I bought the auxbeam 8 gang panel. I’m guessing I need to wire the amber lights separately on the relay box. Do I split the grounds and use same one? Not sure yet
Have all Cali raised and plane on switching all to heretic lights but broke lol but all my Cali raised rusted or rusting got some stuff new that I’m selling and don’t drive in salt to much and clean it a lot just sheep stuff and have there fogs hidden light bar and 43 dual function and bed stiffners
Good to know, how long have you been running the Cali raised stuff for? I'm actually going to install the bumper bar and bed stiffeners here in the next couple days.
@@GearheadJT 2 years but I took pictures and they sent me out new ones for free and kept old grinder them down at work and used steel it paint and they look ok to sell for cheap n bout athen fab bed stiffners and Baja fogs
If you haven’t figured it out I have the same type of wiring. There are 2 positive and 1 negative. If you are wiring this in to a control panel with fuses you will need to piggyback the negative. I’m not sure if I am using the correct terminology, but I can send you pics on Instagram if you have questions. @project_06streetrunner.
Hi. how did you connect the switches for amber and led? mine will only work both and the LED alone, but not with amber alone, i like to see that the amber only works as well while the LED is deactivated.
So I just got the same light bar and I’m a bit confused on the wiring. I also have a switch panel but I just want to make sure I’m doing this right... is the green wire for the ambers? And did you just tie in both grounds to the one coming from the actual light bar? Thanks
i agree. i have the same question. Can you tell us what the 3 green/black/white wires control on the lightbar. so stupid caliraised doesn't include that on the site or in the box!!
Good question, I actually just used the largest in diameter bolt I could find which would fit through the bracket, and also used the hardware which came with the light bar.
So the light bar comes with a harness and switch, I cut it and used part of the harness to connect the lights to my 8 Switch Light Panel. You can see the switch panel video here: th-cam.com/video/ke3Nn7-kgmY/w-d-xo.html
@@GearheadJT bro I have the same light bar and now I got the switch panel.. my question is how to connect the amber and white separate my harness has 4 cables one red black white and I think blue??
Great video, i wish you wouldve include how you wire it to the switch panel 😩
My neighbor has a caliraized light bar and it has condensation in it after one rainy season. I'm steering clear of them.
Can you put more info on the accessory switch panel your talking about? I want to do the same on my taco and don't want all these wires running to the battery. Thank you! Your truck is coming out bad ass! Love it!
Thank you, I appreciate it! The Next video will be dedicated to the Accessory Switch Panel, I'll try to release it here in the next couple of days!
@@GearheadJT I have the sPod bantam with Touchscreen and will be connecting the same light bar. I plan run the amber and white lights independently. Plus I'd like to connect the amber into the running lights but have to figure out how to do that.
There are two ways you can wire your dual function bar depending on how you would like it to operate.
If you want to control the amber and white separately, then you will need 2 harnesses. With the 2 harnesses, this gives you the ability to run the Amber/White lights individually or all at the same time.
The LED bar will have 3 wires on it. BLACK, WHITE, GREEN
BLACK: Ground WHITE: Power For The White LED's GREEN: Power For The Amber LED's
The harness will have DT Plugs at the end. You will want to remove those plugs as they are not needed.
After the plugs are removed there will be red and black wires exposed. between both harnesses, you will have 2 red wires and 2 black wires.
You will want to connect the 2 black wires together and connect them to the black wire on the LED bar, Then one red to the white and the other red to green. That will give you the ability to run the lights independently.
If you are just wanting the full bar to turn on/off at once and not be able to control separately then you would just need one harness. Remove the plug from the harness. Connect the black wire from the LED bar to the black wire on the harness. Then combine the green and white wire on the LED bar to connect to the red on the harness.
Awesome! Any video reviews of the actual headlight output? Ordered these but hearing mixed opinions on them, Thanks!
I bought same set up. Watched this video and your squadron install. Id love to see how you actually wired those lights to that Cali raised switch system. Did you use relays? Or can you eliminate those with switch system?
One thing I did was either put a thick wax coat on it or ceramic to extend its durability so far so good!
Hey man. Super clean taco. Do you mind sharing the wiring harness that you used for this light bar?
Looks good, I've been eye balling that light, for my DV8 rack. having problems with my rack though.
I just installed mine today on a Prinsu and the same light that failed on yours flickered and then went out on mine. Did you get a replacement or repair this one?
Hey man, I was looking for the recent vid of when they sent you new light bar. Did you end up liking it? Hope to see the review 🙏
I have a 40inch Clear Cali light bar slim on my prinsu for over a year and so far so good.been looking at this dual function but I hear there has been issues with them
I just ordered the same 43" LED and generic switch panel from your other video but am not sure what cable I need to order to run the ambers and white separately to different switches. My LED came with a very short cable running out of the drivers side. What cable do I need to get to hook the LED up to the switch panel? Any info would be appreciated going to do a self instal watching your switch panel instal video! Thanks
How did it work out for you after some time tucking your wire through the windshield? Did you ever have any problems after that?
Just curious on the update with the bar light and did you also order the separate cables to use the dual function or no ?
I used the dual function harness, that way I was able to control the amber lights independently from the white.
I’m about to install this bar on my Southern style offroad rack. I bought the auxbeam 8 gang panel. I’m guessing I need to wire the amber lights separately on the relay box. Do I split the grounds and use same one? Not sure yet
Can you tuck the wire because its pretty thick. I don't want to have to buy a windshield wire hider. Please someone let me know. Thanks
Have all Cali raised and plane on switching all to heretic lights but broke lol but all my Cali raised rusted or rusting got some stuff new that I’m selling and don’t drive in salt to much and clean it a lot just sheep stuff and have there fogs hidden light bar and 43 dual function and bed stiffners
Good to know, how long have you been running the Cali raised stuff for? I'm actually going to install the bumper bar and bed stiffeners here in the next couple days.
@@GearheadJT 2 years but I took pictures and they sent me out new ones for free and kept old grinder them down at work and used steel it paint and they look ok to sell for cheap n bout athen fab bed stiffners and Baja fogs
@@GearheadJT keep doing your reviews, great info as i just got my truck and waiting on accessories.
Where is the renewal of the light output test?
I wish you did the wiring video as well. Did your light bar come with 3 wires attached to it? How did you wire that if so? Thanks
If you haven’t figured it out I have the same type of wiring. There are 2 positive and 1 negative. If you are wiring this in to a control panel with fuses you will need to piggyback the negative. I’m not sure if I am using the correct terminology, but I can send you pics on Instagram if you have questions. @project_06streetrunner.
@@tsstarlin I need help bro
@@RealTa1ent what you got?
Hi. how did you connect the switches for amber and led? mine will only work both and the LED alone, but not with amber alone, i like to see that the amber only works as well while the LED is deactivated.
How to do wire it to the switch panel
So I just got the same light bar and I’m a bit confused on the wiring. I also have a switch panel but I just want to make sure I’m doing this right... is the green wire for the ambers? And did you just tie in both grounds to the one coming from the actual light bar? Thanks
i agree. i have the same question. Can you tell us what the 3 green/black/white wires control on the lightbar. so stupid caliraised doesn't include that on the site or in the box!!
Any updates fellsa
Are the amber more of a yellow or orange color?
Great question, I think more on the yellow side, but I’m color blind...so I’ll ask my wife to check and will report back haha
It’s caliraised what do you expect lol nice taco
I just ordered same led bar and i have the same dv8 roof rack as yours. What size of screw do i use for the custom L brackets?
Good question, I actually just used the largest in diameter bolt I could find which would fit through the bracket, and also used the hardware which came with the light bar.
Did the wiring hold under the weather stripping?
Yes it did without any issues.
What harnnes do you use ? Thanks
So the light bar comes with a harness and switch, I cut it and used part of the harness to connect the lights to my 8 Switch Light Panel. You can see the switch panel video here: th-cam.com/video/ke3Nn7-kgmY/w-d-xo.html
@@GearheadJT
Ok thank you bro
@@GearheadJT bro I have the same light bar and now I got the switch panel.. my question is how to connect the amber and white separate my harness has 4 cables one red black white and I think blue??
Awesome video trying to sell a piece of garbage. Thanks?
Why did you get that rack and not a prinsu?
1. Cost 2. Availability at the time
TIA…