Any good tips on where to by stem replacements? I have a leaking faucet and the screw that retains the rubber washer is broken off. I have been unable to locate the stem replacement.
Can you address the splitter or shutoff valves? You know the brass ones where you turn the little nib to open? I have a bunch which aren't opening or closing completely....help!
"Buy an assortment because it's cheaper." Not by my math! The assortment you picked a sealing washer from will remain 95% unused. What a waste. You paid for all of them ... why?? Just go to a small hardware store that may have more individual parts and buy what you NEED. you won't clutter up your workshop or garage with pieces you'll never use, and you will have spent LESS money buying one washer at a higher single-part price, but at a cost that is far less than a box of 6, 10 or 80 washers, which, if not silicone, age from the day they are made. Peace, pal, and support the tiny hardware stores, keeping your cost and clutter minimized.
@@deasttn oh, yes - everything is my fault. Nice broad condemnation. I just don't like to buy things I don't need. Why would I buy a lot of five different-sized shirts and just wear the only one that fits? That is analogous. You see, I like to take the old washer to a smaller hardware store where you can find just that part you need, and don't have to buy an assortment that will never be used. That is the height of wastefulness, IMO; typical of the modern disposable society. Thank you for your opinion.
@@logmeindangit the advice was for washers and not shirts. Trust me, folks that create videos get tired of keyboard turds like you that knit pick. You probably don't create, and therefore don't understand what I'm talking about, though?
I had a leak on an outside faucet which I foolishly ignored because I was ti cheap to call a plumber but to scared to do it myself. I wasted so much water that my water company alerted me. I followed your video, although I just replaced the whole thing and bam! I fixed the leak. I’m pretty proud of myself!!
Nice step-by-step video. However, I would think twice about using WD40 as it is a petroleum based product that can degrade rubber and some types of plastics. In my opinion, I would suggest using silicone spray as it should not affect negatively affect rubber and plastic.
It's also possible that the washer has increased diameter through being compressed for many years so the new washer you need may be a slightly smaller diameter than the old one.
It's important to replace that washer before you start over-tightening the valve desperately trying to get it to seal, if you've never replaced it and it's not leaking after all these years might as well take a look at it next time you make some time for home maintenance. Once the washer wears away you're gonna be damaging the threading inside and the part where the washer sits and you'll have to replace the whole faucet. Also don't use just any screw you need the right type of screws because this is going to constantly be in contact with metal and water. Now that you've fixed it make sure everyone in the house understands it's no longer necessary to tighten the heck out of that faucet! Bad. Stop it. It feels different, hello. Replacing the faucet is also fairly easy and inexpensive if it's threaded on and not too corroded, but a good bit more involved if it's soldered on or other types of connections you don't have the tools or knowledge for, or if your pipes are very old and rusty proceed with caution. This is why it's preferable to not mess up your faucet and replace the washers. And yes the method used here with two wrenches is also very important you don't want to break anything if there's no threaded connection to loosen (or if it's just really stuck in there) the turning motion can cause something to bend and break. If you don't have the strength in each hand separately get a helper to hold the other part steady in its place.
Thanks for posting! Outdoor faucet leak stopped. I just happened to have the exact size washer needed to replace the old worn out one. Saved my $$ on buying a new faucet.
This is an excellent “help” video! I have watched many many “how to fix” videos but I have never seen and listened to one that was presented so great! Well done! The voice was very easy to understand (even for us southern boys :) and the video moved at an easy to follow pace! Very well done and thank you, Rick
I love the no-nonsense style here, even editing out the breaths. This man respects my time. I also love the super quick repair at the very beginning and the four variants at the end. Quite the information sandwich.
I appreciate that, even I use that method when I have an issue, then I can take time to figure out what to do. Those caps are like gold when you need them
The first thing u learn on german, austrian, (whole eu ?) plumbing scools is: never use mineral oil-based oils or greases on drinking water systems. u can smell this stuff months and years after u have used it... and many seals and washers getting destroyed from it.
@ghij347dereg The Garden faucet is not connected to the main drinking water system ? are you sure that no one will ever drink water there? or on a repair, water gets closed, anyone opens the garden faucet, and the water goes backwards in the drinking water system... or using the water in a pool ? or fish pond ? Oil+ Sardines jummi...
I work at an Ace Hardware store We see issues like this constantly. Many times a rubber washer is all you need. Once in a while we recommend changing out the faucet. Most customer that I see are able to do the job once you show them how easy it is.
Thank you so much for posting these videos. I was able to repair one of my outdoor faucets. I could not have done it without your great videos. Now I have the confidence to repair the other one.
PA LAWN GUY> Why do you keep using the wrenches backwards? For reasonably easy nuts to loosen and tighten, no big deal, if considerably tight or needing considerable tightening they need turned over the opposite from the direction you were using them in the video. The best to you.
Much like D.C. just found out I need to service one. I have, in a pinch, flipped the washer over putting the groove on the back side and the fresh flat side of the rubber towards the seat. Returns the faucet to leak free service until you can get to the hardware store.
I don't think spraying lubricate on the screw that holds the rubber washer is not going to help. It's not going to penetrate to the threads of the screw.
May want to avoid WD-40 on some rubber product as it can degrade them. Also make sure to rinse well before using especially if this is being used for drinking or laundry.
Seems as though WD40 is a YT requirement. YT creators use it for almost everything except cooking and health maladies. I've never found a worthwhile use for it. It actually has no beneficial uses prior to disassembly.
Nice video. clear and efficient. I did notice that the toothbrush left a bristle that got stuck in the seat. The cloth did not remove it. Suggest checking inside with a flashlight to verify cleanliness before re-assembly.
Ideally, you should get some Never-seize and take all of these style faucets apart and put some Never-seize on all of the threads before ever putting them into service. But late is better than never so if you do have to repair these style faucets after they have been in service, make certain you clean all of the threads and put Never-seize on them so they will be much easier to disassemble later.
@@llremmynightfall9246 mine and my neighbors are sweated on. Houses built 30 years apart. Wisconsin. My grandparents house in Illinois were soldered. I’ll ask my other neighbor that just retired as a plumber. Maybe most are threaded now.
Reseating tool was great in my bathroom. You need it when the washer replacement doesn't work. We have lots of minerals in our lines and there were grooves and deposits that needed smoothed.
Thanks for this - simple to follow video saved me a lot of pain - didn't realize such a small washer could cause so much trouble. Bought a little package so that if it happens in the future, I can fix it in literally minutes!
He meant quarter-turn ball valves under sync same type as the ones you are talking about outside period but made for different application. PS they suck ball valve is usually designed for gas using them for water is not the best idea I don't know who the hell ever thought of that. But they were initially designed for gas, Waters designed to be throttled on slowly throttle off slow none of this quick on an obvious which is not good for your plumbing system... and yes I've been a plumber for many many years
@@nebmilo5024, I've never used those for indoor plumbing connections. They don't get used often like outdoor hose bibs where I may turn them off and on several times in a day. I became impatient with washers eroding. Outdoor biibs are much more substantial the the indoor compression fittings.
A lot of people are having outdoor faucets replaced on a regular basis, whether they are the traditional brass type or newer frost free or other premium faucets. My two outdoor faucets were installed in 1926 when the house was built. In Canada and other cold climates it's important to turn off outdoor faucets and drain them of water before they freeze in winter and split the castings. Other than that, I replace washers about every five years and sometimes have replaced or bumped up the packing material that's in the bonnet to prevent a stem leak. A little simple maintenance goes a long way and I don't expect to be replacing any outdoor faucets in my lifetime.
I recommend at least a visual inspection of the valve seat when changing a tap washer. If it has been leaking for a long time the valve seat will have been eroded to some degree. Easier to recut it while you have the whole thing open.
Also replace the packing in the packing nut, also put some valve stem grease in there... It's not always just this simple but this video gives enough knowledge for most people to get the job done...
It would of been a good idea that if in old facets the valve stem may be hard to turn and if you loosen the nut it will leak around the stem ,the stem packing may also be purchased where you get the washers and is also easy to replace.
Whoever did the electrical or the plumbing needs to do it the right way never have an electrical plug below a water source. That electrical outlet is not even a GFI. I would sure hate to be in that garage if that water line sprays water into that electrical outlet. Always make sure the electrical is above the water source and away from it the rule of thumb if you can touch the electrical outlet and a water source at the same time you need to have a GFI. Thanks for a great video it was very informative
My guess is they installed the plumbing after the electrical was done, but yes I completely agree it either needs t be changed out or the breaker changed to a GFCI
Haha. I didn't dislike, but am a plumber. But, for all the effort, might as well replace the ones that are threaded onto the pipe and easily spin of for replacement. For the ones that are soldered onto piping, this is a good solution. If you can replace a gasket as shown, you will be able to replace the entire thing and have a better product.
This is pretty awesome but my house was built in 1987 mine looks looks like the second one. I couldn't find a replacement and my brother made it way worse than it originally was. How do I find a replacement for that? My back and front faucet need it horribly bad. Thanks for any help you can provide in advance.
Some good advice for everyone, and one saves lots of money, and, it's fun, thank you. Just a FYI... I noticed you were using your (adjustable wrench) backwards. An adjustable wrench is designed to be used by transferring all the initial force to the thick part, not the weak part that moves, you can break it right off. After you break the nut loose, then you can use it in any fashion you want due to not much force on the weak side. I understand, many times we can only get the wrench in a tight spot the wrong way, that should be the only exception, otherwise, a good quality wrench will last for generations. Additionally, that goes for the combination wrench you used as well, the thick part takes the breaking force, then use it any way you might need to. Thanks again for a great video!
The adjustable wrench was being used in the correct position. You need to put equal counter-force on the spigot in the clockwise direction while the open end wrench is turning the valve nut in the counter-clockwise direction. Watch the video again and you'll see it's being done properly. What isn't proper is failure to remove the packing nut (outer nut) to clean the corrosion from the stem. Once you tighten the packing nut, the rough corrosion on the stem will tear at the packing washer prematurely causing another leak.
He has no clue where or when he used the wrench's/channel lock backwards... He saw a TH-cam video on how to do this and decided to make his own video...
What I've noticed with mine is the screw at the end gets rusted solid (actually it's a 1/4" socket head .vs a Philips). As I have two of the frost proof units, both that started leaking and both had the top of the screw head break off due to rust (even after using WD-40 for a couple days), I'm going to look to see if I can get the entire unit as was displayed here. To be honest, I'm glad I came across this video, as I had started to look at some others and none had the detail that this one does. I'm guessing that I'll have to shut the water off at the main, take one apart, pulling out that rod and then take it to the hardware store so that I get the correct size replacement as I've seen there are different lengths. Thanks for the informative video!
These faucets are for an outdoor washing machine, common in warm climates where you don't have to worry about freezing temperatures so of course you need a power outlet. I remember the first time I was in the Phoeniz area being amazed that many houses had the washing machines outside on a covered patio.
Exactly my case. Main shutoff is in my basement and the house was built in the 50's. There's no direct shutoff to my outside spigot, nor shower. Tried this, and now my main leaks. Ha.
@@FadeToBlack80 yeah I do work on houses,. When there's reason to call in a plumber on a house that isn't fairly new, I usually suggest that they have the plumber check / replace the shut off valves while he's there. The old crappy crusty ones are going to leak at some point it's just a question of when.
I have one like the first faucet demonstrated hooked up to my washing machine. It leaked last week when the water was running. I found the outer collar was loose. I tightened the collar nut with a wrench. I put it in brand new a year or two ago from Lowe's. So far it doesn't leak when the valve is turned off, but your video help me to understand how to fix it if it does.
I also apply silicone plumber's grease on all the metal threads for easier removal of parts for the next time the washer needs to be replaced. Vaseline will also work, but be sure there is no contact with any rubber surfaces.
Pulled the two washers from the outside faucet. First was 7/8" outside with a 3/16" screw hole, second washer for valve stem was 3/4" outside with a 5/16" hole. Home depot and Lowes do not have either washer size. I can't find a kit that has these sizes. After a week of looking, I guess I'll spend the $36 to replace 3 leaky, 16 yo faucets to address a $1.00 problem.
Lemme see if this will work on mine.hmm will the cap cause leakage or break in the walls inside ? Did this the removal of valve put a new gasket in and notha. Maybe just get that cap it's caused a lot of wall damage below faucet.
rubber washer most "people" won't tell you about... yea you mean to say "plumber". I had a plumber recommend a complete toilet replacement until I yell at him and accused of complete shit cause I had experience with the leak. He hurriedly put everything back together and leak was completely gone... never heard from him again. Fraudulent BS...
Mine only leaks when my hose is hooked up and the water is running. In the front and back yard. Any suggestions or thoughts on what it could be? Thanks for your time and videos.
Its likely the outer nut. I would tighten the nut as shown here 4:43 to make it snug and that almost always solves it, make sure its not so tight that it cant turn freely but you will likely find it is super loose
Another tip, if you don't have exact same washer and old one is just worn (groove) and no tear is to get a rubber washer for 1/2 pipes, which has same outer diameter. Place it into the faucet, and put assemble it back. Your new gasket will sit on the metal, then old gasket will press over the new one and since both are rubber, they will seal well, even though old one has some grooves. On the threads you can seal with pipe sealing compound, then add some teflon tape, then extra sealing compound. Clean threads first.
General comment. Clean up all the brass parts with a wire brush while you’re at it..as limescale buildup (UK in particular) can cause issues when assembling the unit again Ive found. Some plumbers paste/grease also goes a long way (future wise in particular) when it comes to assembling in general, and if you ever have to replace the washer again..not to mention prolonging the time in replacing the washers in the distant future and overall 👍🏻
You know what I already knew about how to fix the leaks and strange enough the screw cap you showed at the beginning is what I found interesting as I have not seen it before.
you covered so much here, other TH-camrs would of milk it into a series of sitcom videos. great job saves me a lot of money by doing research and buy parts and did it myself. TY
@@SilverCymbalthank you, you know that outer nut also has a washer and I never know where to get that washer because the hole of that washer is much bigger than the washer kit (which i also got).
In an emergency, you can simply put the washer on backwards to temporarily stop the leak. Nothing to do with saving money, sometimes you may not be able to go out, given the current state of lockdowns and so on. That means we can practice all kinds of home repairs while locked in 😂😂
You are using the wrenches backwards. That's a good way to snap off the smaller part of the open end and adjustable wrenches. You want to apply force in the direction of the smaller end, not like you did by applying it to the larger end of the wrench.
Nonsense. Open end wrenches are usually angled in one direction to facilitate working in tight spaces. There is no particular orientation that's right or wrong. I've used cheater bars and hammers many times on such wrenches and I have never snapped one off.
@@10-4CodyWade that's the second comment I've seen saying that about the wrench being backwards .... idk what yt video they learned that from . It's comical to say the least
Nice vid, I have that frost free type that was leaking and I went out t find the whole shaft but home depo only had an assortment kit that had a combination of each gasket possible for those types, just not my kind, I used one that was close but still leaking. I was about to replace the whole thing but now I know it’s just that gasket. Thanks
Note: If the Knob/handle is stuck on the shaft from corrosion (common in old homes), you DONT need to remove it, the whole "cartridge assembly" will still come out to access the rubber sealing washer.
Thanks for watching please LIKE & SUBSCRIBE - Sealing Caps: amzn.to/3ajnN9b Washer Kit: amzn.to/3wZJe97
Any good tips on where to by stem replacements? I have a leaking faucet and the screw that retains the rubber washer is broken off. I have been unable to locate the stem replacement.
Awesome video! And very informative and detailed! Great job!
@@mdawn1984 check on Google like what size is your faucet and you could buy a faucet repair kit you'll get many sizes!
@My Pets true
Can you address the splitter or shutoff valves? You know the brass ones where you turn the little nib to open? I have a bunch which aren't opening or closing completely....help!
The only time I make $100 an hour tax free is when I do home and auto repairs myself
"Buy an assortment because it's cheaper." Not by my math! The assortment you picked a sealing washer from will remain 95% unused. What a waste. You paid for all of them ... why??
Just go to a small hardware store that may have more individual parts and buy what you NEED. you won't clutter up your workshop or garage with pieces you'll never use, and you will have spent LESS money buying one washer at a higher single-part price, but at a cost that is far less than a box of 6, 10 or 80 washers, which, if not silicone, age from the day they are made. Peace, pal, and support the tiny hardware stores, keeping your cost and clutter minimized.
You're petty and the reason that folks don't like to make youtube videos
@@deasttn oh, yes - everything is my fault. Nice broad condemnation.
I just don't like to buy things I don't need. Why would I buy a lot of five different-sized shirts and just wear the only one that fits? That is analogous. You see, I like to take the old washer to a smaller hardware store where you can find just that part you need, and don't have to buy an assortment that will never be used. That is the height of wastefulness, IMO; typical of the modern disposable society.
Thank you for your opinion.
@@logmeindangit the advice was for washers and not shirts.
Trust me, folks that create videos get tired of keyboard turds like you that knit pick.
You probably don't create, and therefore don't understand what I'm talking about, though?
I had a leak on an outside faucet which I foolishly ignored because I was ti cheap to call a plumber but to scared to do it myself. I wasted so much water that my water company alerted me. I followed your video, although I just replaced the whole thing and bam! I fixed the leak. I’m pretty proud of myself!!
Nice step-by-step video. However, I would think twice about using WD40 as it is a petroleum based product that can degrade rubber and some types of plastics. In my opinion, I would suggest using silicone spray as it should not affect negatively affect rubber and plastic.
It's also possible that the washer has increased diameter through being compressed for many years so the new washer you need may be a slightly smaller diameter than the old one.
Brother use wd 40 silicone.....regular wd 40 will decrease the life time of rubber......
You're replacing the rubber...
Lol he's replacing the washer.
It's important to replace that washer before you start over-tightening the valve desperately trying to get it to seal, if you've never replaced it and it's not leaking after all these years might as well take a look at it next time you make some time for home maintenance. Once the washer wears away you're gonna be damaging the threading inside and the part where the washer sits and you'll have to replace the whole faucet. Also don't use just any screw you need the right type of screws because this is going to constantly be in contact with metal and water. Now that you've fixed it make sure everyone in the house understands it's no longer necessary to tighten the heck out of that faucet! Bad. Stop it. It feels different, hello.
Replacing the faucet is also fairly easy and inexpensive if it's threaded on and not too corroded, but a good bit more involved if it's soldered on or other types of connections you don't have the tools or knowledge for, or if your pipes are very old and rusty proceed with caution. This is why it's preferable to not mess up your faucet and replace the washers. And yes the method used here with two wrenches is also very important you don't want to break anything if there's no threaded connection to loosen (or if it's just really stuck in there) the turning motion can cause something to bend and break. If you don't have the strength in each hand separately get a helper to hold the other part steady in its place.
Outstanding video with very clear, concise explanations. I was able to fix my faucet in minutes with this. Many thanks
Thanks for posting! Outdoor faucet leak stopped. I just happened to have the exact size washer needed to replace the old worn out one. Saved my $$ on buying a new faucet.
This just popped into my feed and I would like to know how the heck youtube knew I had a leaky spiggot?.......scary amazing.
This is an excellent “help” video! I have watched many many “how to fix” videos but I have never seen and listened to one that was presented so great! Well done! The voice was very easy to understand (even for us southern boys :) and the video moved at an easy to follow pace! Very well done and thank you, Rick
4:20 did you leave a toothbrush filament inside the valve body? :)
Great video, thanks!
He sure did. That show how unprofessional people who are trying to teach people to fix things or create more problems
I wonder how many people put a hose cap on a frost free and forgot about it in the winter after watching this video
Good video. Always turn the stem all the way out when removing and reinstalling.
4:12 you left tooth brush hair in there lol
I love the no-nonsense style here, even editing out the breaths. This man respects my time.
I also love the super quick repair at the very beginning and the four variants at the end. Quite the information sandwich.
Would it be ideal just to replace it with a ball valve spigot? Flow won't be smooth but it shouldn't ever leak. :-)
I agree.
Upvoted because the first thing you showed is a way for anyone to fix the issue quickly with no effort.
I appreciate that, even I use that method when I have an issue, then I can take time to figure out what to do. Those caps are like gold when you need them
The first thing u learn on german, austrian, (whole eu ?) plumbing scools is:
never use mineral oil-based oils or greases on drinking water systems. u can smell this stuff months and years after u have used it...
and many seals and washers getting destroyed from it.
@ghij347dereg The Garden faucet is not connected to the main drinking water system ? are you sure that no one will ever drink water there? or on a repair, water gets closed, anyone opens the garden faucet, and the water goes backwards in the drinking water system...
or using the water in a pool ? or fish pond ? Oil+ Sardines jummi...
I work at an Ace Hardware store We see issues like this constantly. Many times a rubber washer is all you need. Once in a while we recommend changing out the faucet. Most customer that I see are able to do the job once you show them how easy it is.
Thank you so much for posting these videos. I was able to repair one of my outdoor faucets. I could not have done it without your great videos. Now I have the confidence to repair the other one.
Go get it bud! To quote Ron Swanson on DIY... "The sense of accomplishment and pride. Dammit... I just love it so much!".
PA LAWN GUY> Why do you keep using the wrenches backwards? For reasonably easy nuts to loosen and tighten, no big deal, if considerably tight or needing considerable tightening they need turned over the opposite from the direction you were using them in the video. The best to you.
Great video, concise. You should do one on leaking out of the stem when the faucet is turned on.
The stem packing is the next point of leakage. 😊
Very timely for me 😉 I've got one faucet that needs attention. Thanks for another great video! 👍
Much appreciated, glad it was helpful
Same! I was looking at a slow drip outside yesterday
Much like D.C. just found out I need to service one. I have, in a pinch, flipped the washer over putting the groove on the back side and the fresh flat side of the rubber towards the seat. Returns the faucet to leak free service until you can get to the hardware store.
Nice crisp video.
You could also use the old washer's back side if the rubber is not cracked up.
My faucet is actually leaking and I’ve been putting off calling a plumber. What amazing timing. Thank you!
Don't forget that the tap has to be open while doing this. I crushed the seat once while tightening it back together.
Good Tip. Great Video
I don't think spraying lubricate on the screw that holds the rubber washer is not going to help. It's not going to penetrate to the threads of the screw.
39 plumbers disliked this video...😉 like from me.!
May want to avoid WD-40 on some rubber product as it can degrade them. Also make sure to rinse well before using especially if this is being used for drinking or laundry.
Seems as though WD40 is a YT requirement. YT creators use it for almost everything except cooking and health maladies. I've never found a worthwhile use for it. It actually has no beneficial uses prior to disassembly.
My OCD is so annoyed you left a bristle of the tooth brush in the tap before you put it back together
Yup...but if Makes you happy that bristle will come out when water flows out
Nice video. clear and efficient. I did notice that the toothbrush left a bristle that got stuck in the seat. The cloth did not remove it. Suggest checking inside with a flashlight to verify cleanliness before re-assembly.
It'll come out eventually with the water flow
Thanks man I never knew how to do this. I thought I had to call a plumber to fix the leak
Fixes leaking washing machine hookups in a rental. Took less than 1 hr, including the trip to the HW store. THANKS!
Thanks dad. I'm nervous but feel much more confident after watching.
Glad it was helpful
@@SilverCymbal subscribed, thumbs up.
Ideally, you should get some Never-seize and take all of these style faucets apart and put some Never-seize on all of the threads before ever putting them into service. But late is better than never so if you do have to repair these style faucets after they have been in service, make certain you clean all of the threads and put Never-seize on them so they will be much easier to disassemble later.
Is your water that toxic that you need the nitrile gloves?
He might think he is going to get an electric shock or something or it just looks good.
or the water is going to rot his skin.
Not worth fixing. They don’t last as long.
You really need to show how to repack the stem nut with teflon or graphite packing.
These are called boiler drains, and cost .no more than $5. Why waste your time?
@@llremmynightfall9246 - Because we’re REALLY cheap. I do this then go buy a beer with the 5 bucks.
@@llremmynightfall9246 also because it’s a LOT easier than sweating on a new valve.
@@d.vanwinkle9482 I guess your not a plumber. Its an IPS valve guy...no sweating involved. Unscrew old out, screw new in.
@@llremmynightfall9246 mine and my neighbors are sweated on. Houses built 30 years apart. Wisconsin. My grandparents house in Illinois were soldered. I’ll ask my other neighbor that just retired as a plumber. Maybe most are threaded now.
Reseating tool was great in my bathroom. You need it when the washer replacement doesn't work. We have lots of minerals in our lines and there were grooves and deposits that needed smoothed.
That's a great tip and for an indoor valve it's definitely worth the effort since that can get very expensive fast.
For a permanent solution swap it with a silicone washer.
@4:23 reinserts the stem back into the faucet body with a loose toothbrush bristle still inside to keep the new washer from making a proper seal LOL.
I saw that bristle there as well.
Thanks for this - simple to follow video saved me a lot of pain - didn't realize such a small washer could cause so much trouble. Bought a little package so that if it happens in the future, I can fix it in literally minutes!
I just replaced all my screw bibs with quarter turn ball valve bibs.
I’ve had so many 1/4 valves break. Not fun flooding out a kitchen at a Wells Fargo office
@@gcahal1 Hose bibs are all outside.
I don't think they are appropriate for indoor installation.
He meant quarter-turn ball valves under sync same type as the ones you are talking about outside period but made for different application. PS they suck ball valve is usually designed for gas using them for water is not the best idea I don't know who the hell ever thought of that. But they were initially designed for gas, Waters designed to be throttled on slowly throttle off slow none of this quick on an obvious which is not good for your plumbing system... and yes I've been a plumber for many many years
@@nebmilo5024, I've never used those for indoor plumbing connections. They don't get used often like outdoor hose bibs where I may turn them off and on several times in a day. I became impatient with washers eroding. Outdoor biibs are much more substantial the the indoor compression fittings.
I bought a splitter that i screwed on and it stops the leak.
A lot of people are having outdoor faucets replaced on a regular basis, whether they are the traditional brass type or newer frost free or other premium faucets. My two outdoor faucets were installed in 1926 when the house was built. In Canada and other cold climates it's important to turn off outdoor faucets and drain them of water before they freeze in winter and split the castings. Other than that, I replace washers about every five years and sometimes have replaced or bumped up the packing material that's in the bonnet to prevent a stem leak. A little simple maintenance goes a long way and I don't expect to be replacing any outdoor faucets in my lifetime.
Manufacturing and design was better 100 years ago, kudos for maintaining things!
I recommend at least a visual inspection of the valve seat when changing a tap washer. If it has been leaking for a long time the valve seat will have been eroded to some degree. Easier to recut it while you have the whole thing open.
Also replace the packing in the packing nut, also put some valve stem grease in there...
It's not always just this simple but this video gives enough knowledge for most people to get the job done...
Kids love drinking from the hose right after the WD40 treatment !
Mmmmmm....
It would of been a good idea that if in old facets the valve stem may be hard to turn and if you loosen the nut it will leak around the stem ,the stem packing may also be purchased where you get the washers and is also easy to replace.
He completely left out the valve stem washer repair which almost always needs attention, not just tightening on a 20 year valve.
Whoever did the electrical or the plumbing needs to do it the right way never have an electrical plug below a water source. That electrical outlet is not even a GFI. I would sure hate to be in that garage if that water line sprays water into that electrical outlet. Always make sure the electrical is above the water source and away from it the rule of thumb if you can touch the electrical outlet and a water source at the same time you need to have a GFI. Thanks for a great video it was very informative
My guess is they installed the plumbing after the electrical was done, but yes I completely agree it either needs t be changed out or the breaker changed to a GFCI
Thanks for sharing. This is on my weekend "to do" list.
0:24 Caps will fix the problem!!! (fails to mention, serious damaged in winter when that water freezes.
You left a bristle inside when you scrubbed it with the toothbrush, and it was not removed before reassembly.
It'll eventually work it's way out.
Oh be quiet, would you?!!
@@chocluva2678 I knew there would be someone to say.
2 dislikes from plumbers. Thxs for the vids!
Haha. I didn't dislike, but am a plumber. But, for all the effort, might as well replace the ones that are threaded onto the pipe and easily spin of for replacement.
For the ones that are soldered onto piping, this is a good solution.
If you can replace a gasket as shown, you will be able to replace the entire thing and have a better product.
@@stephenmartin7907 just as simple to replace one that’s sweated on also, you’re a plumber?
@@kosmaswhite6202 hahaha. I like that. :-)
Honestly, the frost free valve on mine was so damaged that I just had to replace the whole assembly and I got a vacuum breaker with the new one...
I replace with Quarter turn valves! So much faster to turn on/off.
What is that nozzle you have for your WD40 spray. It looks interesting. We you have a link to it?
Did a quick search. Looks like it could be EZ-REACH. Appears to be sold on WD40 cans.
You should have cleaned the body with a fine wire brush to clean the green corrosions off
This is pretty awesome but my house was built in 1987 mine looks looks like the second one. I couldn't find a replacement and my brother made it way worse than it originally was. How do I find a replacement for that? My back and front faucet need it horribly bad. Thanks for any help you can provide in advance.
My hat is off to you… you know a ton of stuff... 💪🏼. Thanks for making these videos. 👍🏻. Troy
ya cant get parts anymore,
But you do realize is alot easier just to unscrew the goddam thing and screw a new one in no
Some good advice for everyone, and one saves lots of money, and, it's fun, thank you. Just a FYI... I noticed you were using your (adjustable wrench) backwards. An adjustable wrench is designed to be used by transferring all the initial force to the thick part, not the weak part that moves, you can break it right off. After you break the nut loose, then you can use it in any fashion you want due to not much force on the weak side. I understand, many times we can only get the wrench in a tight spot the wrong way, that should be the only exception, otherwise, a good quality wrench will last for generations. Additionally, that goes for the combination wrench you used as well, the thick part takes the breaking force, then use it any way you might need to. Thanks again for a great video!
The adjustable wrench was being used in the correct position. You need to put equal counter-force on the spigot in the clockwise direction while the open end wrench is turning the valve nut in the counter-clockwise direction. Watch the video again and you'll see it's being done properly. What isn't proper is failure to remove the packing nut (outer nut) to clean the corrosion from the stem. Once you tighten the packing nut, the rough corrosion on the stem will tear at the packing washer prematurely causing another leak.
He has no clue where or when he used the wrench's/channel lock backwards...
He saw a TH-cam video on how to do this and decided to make his own video...
@@MrWayneJohn1the wrench is being used wrong at the 5:40 mark
That electrical receptacle to the right of the hot water shut-off should be replaced immediately with a GFCI outlet. That would never fly in my home.
I just watched a ton of videos about this issue and your tutorial is hands down the most informative! Thank you ❤
What I've noticed with mine is the screw at the end gets rusted solid (actually it's a 1/4" socket head .vs a Philips). As I have two of the frost proof units, both that started leaking and both had the top of the screw head break off due to rust (even after using WD-40 for a couple days), I'm going to look to see if I can get the entire unit as was displayed here.
To be honest, I'm glad I came across this video, as I had started to look at some others and none had the detail that this one does.
I'm guessing that I'll have to shut the water off at the main, take one apart, pulling out that rod and then take it to the hardware store so that I get the correct size replacement as I've seen there are different lengths.
Thanks for the informative video!
Take the old one to a well stocked hardware store and replace it with a stainless or brass screw.
Good how to, I had to do this a few years back.
PERFECT timing! I have a faucet to repair this weekend. Thank you!
⁷uh kip juli hip
He uses this one weird trick, now Plumbers hate him.
My water bill isn't even $1000 a year. How much water are you leaking?
My hose leaks where it fixes to the faucet. I think it may need a washer.
Thank you!!! This is the best video on this, now I know we can fix our leaky faucet and not pay a big fee to have someone else do it!
Did anybody else notice the power outlet directly next to the faucets
These faucets are for an outdoor washing machine, common in warm climates where you don't have to worry about freezing temperatures so of course you need a power outlet. I remember the first time I was in the Phoeniz area being amazed that many houses had the washing machines outside on a covered patio.
Of course if you use the main shut off, it'll probably start leaking too. They don't get used very often.
If your house isn't newer
Exactly my case. Main shutoff is in my basement and the house was built in the 50's. There's no direct shutoff to my outside spigot, nor shower. Tried this, and now my main leaks. Ha.
@@FadeToBlack80 yeah I do work on houses,. When there's reason to call in a plumber on a house that isn't fairly new, I usually suggest that they have the plumber check / replace the shut off valves while he's there. The old crappy crusty ones are going to leak at some point it's just a question of when.
Your channel is fantastic. Thanks for making such high quality DIY videos.
Thank you very much! Very nice of you
I have one like the first faucet demonstrated hooked up to my washing machine. It leaked last week when the water was running. I found the outer collar was loose. I tightened the collar nut with a wrench. I put it in brand new a year or two ago from Lowe's. So far it doesn't leak when the valve is turned off, but your video help me to understand how to fix it if it does.
If it still leaks after you tighten it unscrew that outer collar all the way off and re-pack it with oakum.
Mil 🙏 gracias dios lo cuide y lo vediga que vien. Me gusto su manera de explicar thanks brother
I also apply silicone plumber's grease on all the metal threads for easier removal of parts for the next time the washer needs to be replaced. Vaseline will also work, but be sure there is no contact with any rubber surfaces.
Excellent tip.
Will Teflon tape do in a pinch?
Pulled the two washers from the outside faucet. First was 7/8" outside with a 3/16" screw hole, second washer for valve stem was 3/4" outside with a 5/16" hole. Home depot and Lowes do not have either washer size. I can't find a kit that has these sizes. After a week of looking, I guess I'll spend the $36 to replace 3 leaky, 16 yo faucets to address a $1.00 problem.
Lemme see if this will work on mine.hmm will the cap cause leakage or break in the walls inside ? Did this the removal of valve put a new gasket in and notha. Maybe just get that cap it's caused a lot of wall damage below faucet.
Would have good to explain fixing the top vacuum breaker that is normally the leak issue on no-freeze faucets.
rubber washer most "people" won't tell you about... yea you mean to say "plumber". I had a plumber recommend a complete toilet replacement until I yell at him and accused of complete shit cause I had experience with the leak. He hurriedly put everything back together and leak was completely gone... never heard from him again. Fraudulent BS...
Thanks SC ….. you have a lot of home repairs and projects! Thanks!
Mine only leaks when my hose is hooked up and the water is running. In the front and back yard. Any suggestions or thoughts on what it could be? Thanks for your time and videos.
Its likely the outer nut. I would tighten the nut as shown here 4:43 to make it snug and that almost always solves it, make sure its not so tight that it cant turn freely but you will likely find it is super loose
@@SilverCymbal awesome. Thanks so much. It's been leaking for years. I'm on it tomorrow before spreading my grubx. Thanks again.
@@christopherbonanno1120 I couldn't put my finger on it. Thanks for your help. 🤣
This was a great help because I have that same problem and now I am going to do the job myself ! Thanks once again Sir !
Another tip, if you don't have exact same washer and old one is just worn (groove) and no tear is to get a rubber washer for 1/2 pipes, which has same outer diameter. Place it into the faucet, and put assemble it back. Your new gasket will sit on the metal, then old gasket will press over the new one and since both are rubber, they will seal well, even though old one has some grooves. On the threads you can seal with pipe sealing compound, then add some teflon tape, then extra sealing compound. Clean threads first.
Plumbers don't want you to know this!
Watches a bunch of Sopranos clips….YT recommends i watch how to fix leaky faucet 🤷🏼♂️
Bada bing!
He never had the makings of a varsity athlete
General comment. Clean up all the brass parts with a wire brush while you’re at it..as limescale buildup (UK in particular) can cause issues when assembling the unit again Ive found.
Some plumbers paste/grease also goes a long way (future wise in particular) when it comes to assembling in general, and if you ever have to replace the washer again..not to mention prolonging the time in replacing the washers in the distant future and overall 👍🏻
You know what I already knew about how to fix the leaks and strange enough the screw cap you showed at the beginning is what I found interesting as I have not seen it before.
But oddly enough, the "fixer" doesn't know how to use a Crescent wrench or channel locks. LOL.
I’ve seen many vids on youtube that the person does not know how to properly use tools.
you covered so much here, other TH-camrs would of milk it into a series of sitcom videos. great job saves me a lot of money by doing research and buy parts and did it myself. TY
Glad you liked it!
@@SilverCymbalthank you, you know that outer nut also has a washer and I never know where to get that washer because the hole of that washer is much bigger than the washer kit (which i also got).
This happens to my kitchen faucet. It’s so annoying drip drip drip 💧.....
Good info, thanks for sharing 👍!
In an emergency, you can simply put the washer on backwards to temporarily stop the leak.
Nothing to do with saving money, sometimes you may not be able to go out, given the current state of lockdowns and so on. That means we can practice all kinds of home repairs while locked in 😂😂
Definitely. I’ve flipped the washer over to the good side on several faucets and had great results. I am a really cheap bastard though!
Explained nicely, clearly and quickly. Very good video thank you.
You are using the wrenches backwards. That's a good way to snap off the smaller part of the open end and adjustable wrenches. You want to apply force in the direction of the smaller end, not like you did by applying it to the larger end of the wrench.
Nonsense. Open end wrenches are usually angled in one direction to facilitate working in tight spaces. There is no particular orientation that's right or wrong. I've used cheater bars and hammers many times on such wrenches and I have never snapped one off.
@@10-4CodyWade that's the second comment I've seen saying that about the wrench being backwards .... idk what yt video they learned that from . It's comical to say the least
Nice vid, I have that frost free type that was leaking and I went out t find the whole shaft but home depo only had an assortment kit that had a combination of each gasket possible for those types, just not my kind, I used one that was close but still leaking. I was about to replace the whole thing but now I know it’s just that gasket. Thanks
Note: If the Knob/handle is stuck on the shaft from corrosion (common in old homes), you DONT need to remove it, the whole "cartridge assembly" will still come out to access the rubber sealing washer.
Thanks for your instruction it's saving money for calling a plumber, God bless you and your family..