REWA Technology I need help for ram upgrade, The model is K3QF6F60MM-QCGF, I need to solder this into my Tablet, configuration is RAM over SOC, soc is Tegra K1
It is more common to have unfixable problems that are internal to the Baseband CPU. Consider yourself lucky if just replacing the baseband PMU is all you need
Yep, if your real lucky none of those 3 shorts will trace back to the BBCPU. I've only seen one that I traced to an RF chip through a 0 ohm resistor. I replaced it and it came back alive. But most of the time i trace it to the BBCPU.
John Baker This 4013 was a freaking odyssey Short on BBPMU_TO_PMU_AMUX3 XCVR1_RF Heating up on dpcs removed short gone have not replaced PP_VDD_XCVR1_RF1_RX >>>> PP_0V9_LDO3 Short BB_PMIC heating up so removed and replaced Short gone I don’t need XCVR1_RF to boot right? So I have not replaced it but still 4013 i flashed ios12 beta1 and get the could not activate of course shutdown lmao
can you see an IMEI in 3u tools? If not that is why you cant activate. I wouldn't be so sure you don't need that RF chip. Sounds like something was problematic and created all this mess. Lets hope it was BBPMU and not the BBCPU
Baseband voltages don’t appear in recovery mode. If they’re present they’ll quickly flash during an attempted boot before it reboots (typical problem with error 4013 when not forced in recovery or DFU). They also appear very briefly when attempting a restore at the beginning of the process. If they’re missing at those moments then suspect a bad bb PMU granted none are shorted due to baseband ic pulling them down or a capacitor on the rails
now iphone can't be detected by Pc stuck in DFU mode. but when you insert usb and the iphone is off it turns on to dfu but can't be recognized in 3utools or itunes.
How much Reading Value on a MULTEMER do u you consider as NORMAL and how much do you consider as ABNORMAL when measuring the voltage on the resistors such as (C1701,C1721)
Here for it: Multimeter: www.rewatechnology.com/digital-multimeter-type-3-13472.html 4 in 1 Integrated Rework Station for Mobile Phone Repair: www.rewatechnology.com/4-in-1-integrated-rework-station-for-mobile-phone-repair-15558.html Any questions and demands please feel free to contact us at: sales@rewatechnology.com
I just received a phone for LCD Assembly replacement, the phone booted in recovery mode so i tried to exit without success and when i tried to restore/update the 5s reboots and started bootlooping. Then the "error 4013" happened , and you guys uploaded the video just in the right moment, wow! I am not sure yet which component causes this problem, but we will see. By the way, is the procedure for 5s or 6 the same?
Because of the normal supply of voltage to the bb pmu, so there is a possibility that it is problem from the the bb pmu itself. Of cause, it may not but it is the first easier step to check out first.
Can you teach how to repair iPhone SE with error -1 as I have that problem and don’t have the tools or knowledge to repair so if I hear reliable stuff from your video I may attempt
L HK I bought it as spares repair and it booted into recovery mode . Managed to get it to boot when restoring iOS 12 beta 1 as it ignores baseband however as it has no imei from broken baseband I could not activate it
What we want to show in this video is not the repair case but the troubleshooting method. iPhone 7/7Plus error 4013 may be related to CPU, Baseband and NAND Flash, but we usually start from the simple and most likely part.
Easier, because you do not update to the latest iOS 12 beta update and you will not lose your information. First for the device in recovery mode. (Remember to update by pressing the shift key in windows and Mac with the command key and select the iOS 12 Beta)
I have an Iphone 7 boot looping and has error 4013 when restoring. I have NAND Voltages and C5622 PP_VDD_MAIN voltages but nothing on C5631 PP_1V225_SMPS2... I reballed BB PMU, no change, replaced with known good PMU and no change. I removed and reprogrammed NAND, no change, I removed and reballed BB CPU, no change, replaced Tristar and no change. I cannot find any shorts and not sure what to try next... any ideas?
Since you are still have the issue, I would start by removing and replacing with new or known good parts. If the reprogrammer can read and write to the NAND, the NAND isn't the issue. But, if you have one you can swap in, give it a shot. Assemble and retest. Next, I would swap in a new BB_PMU, or at least a 'known good' PMU from another board. Assemble and retest.
I just got this update error code 4013, updated process commenced through the latest macbook pro (those with the type-c connectors). I connected the original apple cable via this type c USB device (Satechi), which I suspect the cause of the problem as the device probably couldn't supply sufficient voltage to the iphone 7 for update. Problem solved after I plugged the iphone cable to the back of my monitor which is connected to my computer using type c connector.
You know.. every iphone repair place i know where i live only replaces broken scrren or dead batteries.. ill never find a guy like this where i live.. time to buy a new phone FmL
good afternoon dear friends. kinds regards from Dominican Republic, it is more than a pleasure to write you. Will be.possible to Change the color of the words, we are going to have better view to read the subtitle.
i have error 4013 on my iphone 7 plus.. can somebody help me to solve and work on it...? My macOS is already Updated my Music(itunes) has been updated also i even got original chord with me! thank you! God Bless!
hello sir i have 5s, recently i accidentally dropped it and stuck at recovery mode tried to restore, update but getting continuously error 4013 any solution help me please
![เป็นไปได้ไหม - WanMai [Performance Video]](http://i.ytimg.com/vi/Eh5hItD4Mr0/mqdefault.jpg)
Leave us a comment about the iPhone iTunes errors you frequently encountered.
thx, how about error 4014?
REWA Technology I need help for ram upgrade, The model is K3QF6F60MM-QCGF, I need to solder this into my Tablet, configuration is RAM over SOC, soc is Tegra K1
iphone 4- 6 always happen
Sir how to mesure voltage by schematic diagram
@Ady Vali Most of the 4014 errors are caused by the fault of SDRAM.
you know i don't have a laboratory in my room .. I came here to find a solution for what seems to be a software problem
Did you find a solution? out of interest
I'm just taking mine to get fixed because i also do not have a full blown phone repair shop in my room.
@@yoocarl8613 funnily enough I actually turned my room Into an iPhone repair shop
Mattf14 i dont have the patience. its a bad time for my phone to be screwed up considering work, school, and sports.
@gxthboi.trxxsh give me it vro
What is the normal measurement for the nand and cpu?
It is more common to have unfixable problems that are internal to the Baseband CPU. Consider yourself lucky if just replacing the baseband PMU is all you need
John Baker yesterday alone I had two, one short internal to bbcpu and another with 3 different rf lines shorted and still 4013
Yep, if your real lucky none of those 3 shorts will trace back to the BBCPU. I've only seen one that I traced to an RF chip through a 0 ohm resistor. I replaced it and it came back alive. But most of the time i trace it to the BBCPU.
John Baker This 4013 was a freaking odyssey
Short on BBPMU_TO_PMU_AMUX3
XCVR1_RF Heating up on dpcs removed short gone have not replaced
PP_VDD_XCVR1_RF1_RX >>>> PP_0V9_LDO3 Short
BB_PMIC heating up so removed and replaced
Short gone
I don’t need XCVR1_RF to boot right? So I have not replaced it but still 4013 i flashed ios12 beta1 and get the could not activate of course shutdown lmao
can you see an IMEI in 3u tools? If not that is why you cant activate. I wouldn't be so sure you don't need that RF chip. Sounds like something was problematic and created all this mess. Lets hope it was BBPMU and not the BBCPU
Baseband voltages don’t appear in recovery mode. If they’re present they’ll quickly flash during an attempted boot before it reboots (typical problem with error 4013 when not forced in recovery or DFU). They also appear very briefly when attempting a restore at the beginning of the process. If they’re missing at those moments then suspect a bad bb PMU granted none are shorted due to baseband ic pulling them down or a capacitor on the rails
what should the voltages be for C5623, C5631, C1701, C1721, C1704?
now iphone can't be detected by Pc stuck in DFU mode. but when you insert usb and the iphone is off it turns on to dfu but can't be recognized in 3utools or itunes.
Can you upload a video for iphone 7 plus error 9 and error 1 thanks .
Thanks for the suggestion. We will take it into consideration and keep improving.
Can you upload how to settle iPhone 6 temperature problem
where do I buy these chips?
How much Reading Value on a MULTEMER do u you consider as NORMAL and how much do you consider as ABNORMAL when measuring the voltage on the resistors such as (C1701,C1721)
did you just replace the baseband without reballing?
can i do it for the nand ic ?
Where can i buy the multimeter you have?
And the power shell?
Here for it:
Multimeter: www.rewatechnology.com/digital-multimeter-type-3-13472.html
4 in 1 Integrated Rework Station for Mobile Phone Repair: www.rewatechnology.com/4-in-1-integrated-rework-station-for-mobile-phone-repair-15558.html
Any questions and demands please feel free to contact us at: sales@rewatechnology.com
You are good technician in word sir
I solute u make video to help me thank
Sorry I seem to be missing these tools that I'm too lazy to buy:
4 in 1 Integrated Rework Station: @t
Electron Microscope: @t
Digital Multimeter: @t
PCB holder: @t
Straight Tweezer：@t
Paste Flux: @t
Rosin: @t
Solder Wick: @t
PCB Cleaner: @t
Cutting Nipper: @t
Anti-static Plastic Pry Bar: @t
Soft Brush: @t
Sculpture Knife: @t
Do u have a centre in India?
Very nice video thank you for that plus this is best channel for help :)
I just received a phone for LCD Assembly replacement, the phone booted in recovery mode so i tried to exit without success and when i tried to restore/update the 5s reboots and started bootlooping.
Then the "error 4013" happened , and you guys uploaded the video just in the right moment, wow!
I am not sure yet which component causes this problem, but we will see.
By the way, is the procedure for 5s or 6 the same?
proximity sensor
Why would you replace baseband PMU if all measured voltages are good???
Because of the normal supply of voltage to the bb pmu, so there is a possibility that it is problem from the the bb pmu itself. Of cause, it may not but it is the first easier step to check out first.
Can you teach how to repair iPhone SE with error -1 as I have that problem and don’t have the tools or knowledge to repair so if I hear reliable stuff from your video I may attempt
What happened to your phone that necessitates the restore?
L HK I bought it as spares repair and it booted into recovery mode . Managed to get it to boot when restoring iOS 12 beta 1 as it ignores baseband however as it has no imei from broken baseband I could not activate it
Check baseband voltages when powered up since iOS beta 12 skips bb verification. If missing replace bb PMU after determining no shorts
The problem is most likely related to Baseband PMU or Baseband CPU.
Why would you replace baseband PMU if all measured voltages are fine?
worroSfOretsevraH You wouldn’t. In this video he only measured 2 voltages. Bb PMU has many voltages coming off it. Verify all present first
Yes, but this makes no sense.
Why didn't he first find the missing or wrong voltage, and then assume the PMU is bad, and only then change it.
He considers that cpu is hard to repair in that error that is why he is trying to make a first step by changing that ic before he goes to cpu repair
What we want to show in this video is not the repair case but the troubleshooting method. iPhone 7/7Plus error 4013 may be related to CPU, Baseband and NAND Flash, but we usually start from the simple and most likely part.
Easier, because you do not update to the latest iOS 12 beta update and you will not lose your information. First for the device in recovery mode. (Remember to update by pressing the shift key in windows and Mac with the command key and select the iOS 12 Beta)
iOS 12 beta skip the baseband checking
azmi muwahid Do you know if official iOS 12 release skips bb as well?
mrsemifixit dunno dude
Repair with Jc
Or nAnD
Excellent 👌
Do you have instructions for Ipad 2?
Do you have an Error code 4013 on iPad 2? Error code 4013 is usually related to CPU or NAND chip.
@@rewatechnology2008 Yes I tried all recovery methods . What is the way to solve it ?
I have an Iphone 7 boot looping and has error 4013 when restoring. I have NAND Voltages and C5622 PP_VDD_MAIN voltages but nothing on C5631 PP_1V225_SMPS2... I reballed BB PMU, no change, replaced with known good PMU and no change. I removed and reprogrammed NAND, no change, I removed and reballed BB CPU, no change, replaced Tristar and no change. I cannot find any shorts and not sure what to try next... any ideas?
Since you are still have the issue, I would start by removing and replacing with new or known good parts.
If the reprogrammer can read and write to the NAND, the NAND isn't the issue. But, if you have one you can swap in, give it a shot. Assemble and retest.
Next, I would swap in a new BB_PMU, or at least a 'known good' PMU from another board. Assemble and retest.
I have iPhone 5s and it shows error 9 so please make a video on it
iPhone 5s error 9 is most likely related to NAND Flash.
REWA Technology now I have to replace the nand of iphone
Mine wont restore or update
any fix?
Please make a video about how to unlock iPhone screen lock because I forget my mobile screen pin code
iPhone screen lock can be removed by iTunes restore, but you will lose the data.
@@rewatechnology2008 how
I'm having this error with my iPhone XS Max. Apple told me that it's basically a hardware problem.
exactly the same, did you solve the problem in any shop?
kindly help me to download the restore file. i am unable to find. thank you.
I just got this update error code 4013, updated process commenced through the latest macbook pro (those with the type-c connectors). I connected the original apple cable via this type c USB device (Satechi), which I suspect the cause of the problem as the device probably couldn't supply sufficient voltage to the iphone 7 for update. Problem solved after I plugged the iphone cable to the back of my monitor which is connected to my computer using type c connector.
How much for the cost on repairing this error code? Tq
You know.. every iphone repair place i know where i live only replaces broken scrren or dead batteries.. ill never find a guy like this where i live.. time to buy a new phone FmL
teşekkür ederim sizin sayenizde bir arızayı çözdüm
Dostum benim İphone 5s de 4013 hatası alıyorum Imac'e bağlıyorum sanırım dfu modunda gunceleme yüklerken hata kodu geliyor. Nasıl yapacağız
What if when i conect to the itunes it’s going die after about 30second??? Is that couse of baseband?
Thank you Thank you Thank you very much
Hi
I'm getting the 4013 error in my iPhone 7 is it possible to get my data?
Sir error 4013 shown in iphone 5s
How much pay for repair ??
請問有英特爾版的維修嗎
英特尔版的更换基带电源如果不行换硬盘机能解决了
IPHONE 5S 48 ERROR PROBLEM WHAT IS PROBLEM? REWA HELP ME
how to iphone 6plus error 4013
I have an iPhone 7 Plus with same problems, I am from Bangladesh,
good afternoon dear friends.
kinds regards from Dominican Republic, it is more than a pleasure to write you.
Will be.possible to Change the color of the words, we are going to have better view to read the subtitle.
Thanks a lot for the comment. We do appreciate your suggestions and will keep improving.
Just change your USB cable.. you don't have to do all this lmao
change cable fixed it?
@@icefrog-1032 yep
how to iphone 7plus error 14
Hi iphone 6 19 error software
i have error 4013 on my iphone 7 plus.. can somebody help me to solve and work on it...? My macOS is already Updated my Music(itunes) has been updated also i even got original chord with me! thank you! God Bless!
Pls help me
Tell me what could be the error 3194?
Check your USB port, data cable, and network connection of your computer.
stitched on two computers and two cords, the error remained
My iPhone suddenly started to show iTunes logo and when I tried to restore it using iTunes it shows error 9 can you please help me
it's basic software problem probably itunes problems
That is Great
hello sir
i have 5s, recently i accidentally dropped it and stuck at recovery mode
tried to restore, update but getting continuously error 4013
any solution help me please
Ever get a solution?
@@AllN1TE no bro do you have any idea
If only when I had this problem I was at China
i have iphone 6s error 4013 and i have WL PCIE box but i erase all lowlevel and write backup its same error what the problem please help
genius gamer baseband related in the 6s and up. Check for shorts and/or missing voltages or bad solder under bb cpu
please upload video iphone 6s 4013 error
Good Video but what is the Price in China for this work?? In German we pay a lot of Money 300€.......
Fantastic fantastic.
I need service for ram upgrade!
How can I increase RAM on my iphone?
AppleService By soldering more RAM, but I do not think it will work in apple devices
Yep
@@SuperMan-uj7dh why would you this
this is my issue with my iphone 6 plus. Help me guys please
Master master.
Thanks thanks.
打扰了
Hii make new video
Ho messo mi piace, ma a me il problema era il chip audio pur avendo come errore itunes 4013...
вообще не показательно - прогревается все и проц и нанд и опера, в чем был обрыв хз через день-неделю такое назад принесут на 70%.
Можно снять и паяльником такую микросхему чтобы ничего лишнего не погреть
My iPhone 5s shows error 4013 can you please help me with that
For error code 4013, the fault is usually related to CPU and NAND. You can try to resolder the 2 chips.
buang aja klo udh kya gitu
Are you genuinely
👍
👍👍👍👍
this not 100% solution....... some mobile iphone 7/7 plus not done...... bb power ic change......
iPhone 7/7Plus error 4013 may be related to CPU, Baseband and NAND Flash. This video is just one of the repair cases.
First haha