Thanks for this video. Helped me decide on slapping in the intake valves myself or dropping it off at a shop. 2011 Tiguan 73,000 miles. Failed tensioner
I honestly am shocked at the price to press out the guides and press in new ones. I figured that was a heavy labor job that would cost a lot more. I can attest to the things you've said, as I've been one of those who overlooks the guides and my problems were not fixed. I will say one thing though and I cannot stress this enough, Naptown is spot on as to why he tells us and educates us to buy original Audi parts. You WILL end up paying more by being frugal and buying China. The work will have to be done twice, gaskets, o rings, bolts, etc will have to be bought twice, and your downtime will more than double. Take the extra time to save up a little more and buy original. I've done it and it sucks
Hello. Love your videos. I have an 2011 A4 2.0T with bent valves because it went out of time. Is it possible to remove the head without removing the intake first? Was hoping I could pull the head, exhaust manifold and intake all together then remove them on the bench. Thanks for your entertaining and informative videos
Nice video. Just pulled apart my BHZ ebgine today. Pulled the cam craddle off and found the head and camshafts badly scored. Any idea what would cause this? Faulty oil pump?
Where are you located? I got a 2014 Q5 CPM engine with bad bad misfire on 4. While carbon cleaning, I noticed one of the intake valves seeped cleaner down the cylinder. All the others held well. How much to replace the one bad valve?
Gearing up to go through a 2.0t vw that jumped time. I cannot get motor to complete one rotation. Crank Will only rotate from 1oclock to 11oclock. If ya follow me. Ill be using the crap outta your library. Any thoughts?
Speaking of boost, from your knowledge how much boost does a k03 push on stage 1 or 2? I know it can be different from tuner to tuner but usually what is the safe spot?
i have a k03 on the ea888 1.8t fsi gen 1, with the racechip, my boostguage exceeds 10psi before the diverter valve kicks in , this is supposed to represent stage 1, i had it configured to output more because i have a upgraded intercooler, cold air intake, and a throttle body spacer
@@aminkhan1292 Racechip is worse than a actual remap, an 1.8 tfsi stock is 120hp or 160hp(same engine, marketing strategy) with an actual remap makes 200hp and it should push 1 bar(14.5 psi) at stage 1, my k03 on stage 2 makes 1.2 bar(17.4 psi) until around 4k rpm then less as you go further in the rpm. I was curious what is his answer because i heard people that can make 1.4-1.5 bar with k03 on the 2.0 tfsi but i could not manage to push the turbo on my 1.8tfsi to do that even though my wastegate is ok and i changed the standard dv with an dv+ from gfb. At the moment i make 230hp on a 1.8 tfsi stage 2 with 1.2 bar.
@@noitrex im trying to change my dv but i have a rounded off bolt, im going to cut it out and do the dv+ kit, i got the racechip as i have trade discounts and wanted to manage my hard foot while im on the motorway. the xlr and racechip work well for economy for me. i plan on skipping stage 1 and going straight to stage 2, just waiting on the sports cat
Hey , I watch a lot of your video and am a subscriber , question, if the exhaust valve burn out (crack off) can it fall somewhere it really shouldn’t. One of My exhaust valve broke , should I just replace it ? It’s $20 at fcp euro
Great informative video. Once I heard you mention something about flat earth in your video about feasting and the benefits of it. I would be glad if you will make a video where you would give us your thoughts about flat earth and other touchy subjects. Of course only if you are ok to talk about this on youtube.
I don’t believe I actually mentioned that on my channel, I said “plain of earth” one time. I’ve been learning about all the stuff for about 5 years now and Eventually I’ll start another TH-cam channel or some other platform of some kind so I don’t lose everything. I’ve got such thick skin I’m immune to ridicule so that’s not why I don’t talk about that kind of stuff on here, eventually my entire channel could get wiped away like many others have on the first strike for nothing so I can’t afford for that to happen as I have been putting my life’s savings into trying to make the channel profitable so I don’t have to go to work for someone else again. People can find my Facebook posts, you should be able to find me if you search in “posts” for NaptownTuner I don’t care as much about my Facebook profile being blocked but most everything has moved over to marketplace so that’s the main reason I use Facebook because Craigslist is nothing like it used to be. Google and Facebook taking over.
@@NaptownTuner And I'm just curious. If you are comfortable with it, could you tell me if you belive in the theory of flat earth or not. Sorry for asking questions like that but I just realy wan't to know what your point of view is.
Check you hpfp for wear then make sure your timing belt water pump is done, it’s also a good idea to replace your rear cam adjuster but not as important. I’ll have a few videos on that engine coming up in about a week
Well, my engine failed on me because of the original oil pump ceaced up, if a freewheel is not the solution, then what is? : S Im not gonna buy a new original one, that cost more then what I paid for the car.
These engines are junk. Had a chunk of my exhaust cam gear break off during driving the other day. Took out the upper chain guide mount as well. Im gonna weld that guide mount back on, replace the valves and find a used exhaust cam. Car is up for sale as soon as it gets running again. Shit cars.
Man you’re the BEST Audi/VW guy I’ve ever known!! No kiddin!!
Thanks for this video. Helped me decide on slapping in the intake valves myself or dropping it off at a shop. 2011 Tiguan 73,000 miles. Failed tensioner
Great comparison and why you shouldn't penny pinch on a head overhaul.
Thanks for your wisdom! We’re right at the decision point, this helps.
I honestly am shocked at the price to press out the guides and press in new ones. I figured that was a heavy labor job that would cost a lot more. I can attest to the things you've said, as I've been one of those who overlooks the guides and my problems were not fixed. I will say one thing though and I cannot stress this enough, Naptown is spot on as to why he tells us and educates us to buy original Audi parts. You WILL end up paying more by being frugal and buying China. The work will have to be done twice, gaskets, o rings, bolts, etc will have to be bought twice, and your downtime will more than double. Take the extra time to save up a little more and buy original. I've done it and it sucks
These 2.0TFSI get some serious increase in power from tuning. Would you say that with new chains and pistons it is "safe" or "ok" to tune them?
poured water in my engine, right to the top, nothing came out, should be good to go ?.
hey @NaptownTuner, can you use a gen3 head gasket on a gen2 (2014)? I noticed gen 3 head gaskets lose the oval in the coolant for each cylinder...
Hello. Love your videos. I have an 2011 A4 2.0T with bent valves because it went out of time. Is it possible to remove the head without removing the intake first? Was hoping I could pull the head, exhaust manifold and intake all together then remove them on the bench. Thanks for your entertaining and informative videos
where did you get the valve kit
Nice video. Just pulled apart my BHZ ebgine today. Pulled the cam craddle off and found the head and camshafts badly scored. Any idea what would cause this? Faulty oil pump?
Ran my A5 hot no compression now stg 1 tuned should I just put new heads and replace timing chain ??
I know you can't swap cam trays but can you swap the cams over to different heads
Do you get your valves, gaskets etc. from Rock Auto or someplace similar? Is there a whole head overhaul kit around? Thanks, man, you are the best!
Do you currently have any refurbished heads forsale for a 2.0L CCTA 2012 with new valves/ guides and springs
Where are you located? I got a 2014 Q5 CPM engine with bad bad misfire on 4. While carbon cleaning, I noticed one of the intake valves seeped cleaner down the cylinder. All the others held well. How much to replace the one bad valve?
Gearing up to go through a 2.0t vw that jumped time. I cannot get motor to complete one rotation. Crank Will only rotate from 1oclock to 11oclock. If ya follow me. Ill be using the crap outta your library. Any thoughts?
Who's your valve guy?
Speaking of boost, from your knowledge how much boost does a k03 push on stage 1 or 2? I know it can be different from tuner to tuner but usually what is the safe spot?
i have a k03 on the ea888 1.8t fsi gen 1, with the racechip, my boostguage exceeds 10psi before the diverter valve kicks in , this is supposed to represent stage 1, i had it configured to output more because i have a upgraded intercooler, cold air intake, and a throttle body spacer
@@aminkhan1292 Racechip is worse than a actual remap, an 1.8 tfsi stock is 120hp or 160hp(same engine, marketing strategy) with an actual remap makes 200hp and it should push 1 bar(14.5 psi) at stage 1, my k03 on stage 2 makes 1.2 bar(17.4 psi) until around 4k rpm then less as you go further in the rpm.
I was curious what is his answer because i heard people that can make 1.4-1.5 bar with k03 on the 2.0 tfsi but i could not manage to push the turbo on my 1.8tfsi to do that even though my wastegate is ok and i changed the standard dv with an dv+ from gfb.
At the moment i make 230hp on a 1.8 tfsi stage 2 with 1.2 bar.
I am stage 2 apr with ihi and push 21 psi hold at 18
@@yabbadabba3994 ihi is on a different ball game
@@noitrex im trying to change my dv but i have a rounded off bolt, im going to cut it out and do the dv+ kit, i got the racechip as i have trade discounts and wanted to manage my hard foot while im on the motorway. the xlr and racechip work well for economy for me. i plan on skipping stage 1 and going straight to stage 2, just waiting on the sports cat
Hey , I watch a lot of your video and am a subscriber , question, if the exhaust valve burn out (crack off) can it fall somewhere it really shouldn’t. One of My exhaust valve broke , should I just replace it ? It’s $20 at fcp euro
Valve seat that was.
Where did you get vale seat ?
dude you are an A4 savant. I doubt theres anybody that knows more about these things lol
Great informative video. Once I heard you mention something about flat earth in your video about feasting and the benefits of it. I would be glad if you will make a video where you would give us your thoughts about flat earth and other touchy subjects. Of course only if you are ok to talk about this on youtube.
I don’t believe I actually mentioned that on my channel, I said “plain of earth” one time. I’ve been learning about all the stuff for about 5 years now and Eventually I’ll start another TH-cam channel or some other platform of some kind so I don’t lose everything. I’ve got such thick skin I’m immune to ridicule so that’s not why I don’t talk about that kind of stuff on here, eventually my entire channel could get wiped away like many others have on the first strike for nothing so I can’t afford for that to happen as I have been putting my life’s savings into trying to make the channel profitable so I don’t have to go to work for someone else again.
People can find my Facebook posts, you should be able to find me if you search in “posts” for NaptownTuner I don’t care as much about my Facebook profile being blocked but most everything has moved over to marketplace so that’s the main reason I use Facebook because Craigslist is nothing like it used to be. Google and Facebook taking over.
@@NaptownTuner Thanks a lot. Keep it going.
@@NaptownTuner And I'm just curious. If you are comfortable with it, could you tell me if you belive in the theory of flat earth or not. Sorry for asking questions like that but I just realy wan't to know what your point of view is.
What brand of valves do you buy?
Are tsi and tfsi heads same?
i recently bought a audi a4 2008 cabriolet as my first car. it was really cheap. I was wanting to ask what would you suggestion be for starting mods?
Check you hpfp for wear then make sure your timing belt water pump is done, it’s also a good idea to replace your rear cam adjuster but not as important. I’ll have a few videos on that engine coming up in about a week
ok, i will make sure to check it out
Well, my engine failed on me because of the original oil pump ceaced up, if a freewheel is not the solution, then what is? : S Im not gonna buy a new original one, that cost more then what I paid for the car.
Wait, so can you buy a OE camtray and fit it on a refurb cyl head? Or can you only use the camtray that came with the car originally.
camtray and cylinder head must come as one unit
👍
These engines are junk. Had a chunk of my exhaust cam gear break off during driving the other day. Took out the upper chain guide mount as well. Im gonna weld that guide mount back on, replace the valves and find a used exhaust cam. Car is up for sale as soon as it gets running again. Shit cars.
Whats a good 2.0 turbo car then ?