Chainsaw milling is a lot of fun and I do it as a side job. Next time set up your ladder hang it off the starting end of you log a bit more so you can start your cut easier. It's also a good idea to always use a ladder each cut to help keep each cut as even as possible. Make sure you hold the mill down to the ladder or trees surface to get a consistent thickness of board as well. Get the knowledge needed of how to sharpen your chain properly to give you cleaner faster cuts. Happy milling 👍👍👍👍
Nice One Josh good advice letting the saw cool down me mate had a go at milling some logs after that his new saw needed a engine rebuild🤔 Look forward to see what you make Thanks again
Use the on/off bar on the mill for starting and ending your cuts. It is the bar between the front and rear bar on the mill. You want to have it parallel to your cut not pointing up or down when starting. Also do not twist the mill from side to side, slow steady even pressure makes a smooth cut. Practice and pay attention to what you are doing. Very good for your first try though. Good on you to recognize the need to cool the saw down.
Leave your straight edge on for every cut, otherwise you compound any errors with every slab, get a straight edge with enough overhang for the width of your mill at either end of the log you're cutting to keep it flush at the start and end of the slab. Make sure your rails on the mill are hard down to your straight edge front and back and both sides otherwise you'll get a twisted, uneven slab. Happy cutting, you'll learn heaps just by looking at your process in review and the boards you finish with.
caipira chitãozinho & xororó composição: joel marques/maracai o que eu visto não é linho ando até de pé no chão e o cantar de um passarinho é pra mim uma canção vivo com a poeira da enxada entranhada no nariz trago a roça bem plantada pra servir o meu país sou sou desse jeito e não mudo aqui eu tenho de tudo e a vida não é mentira sou sou livre feito um regato eu sou um bicho do mato me orgulho de ser caipira doutor eu não tive estudo só sei mesmo é trabalhar nesta casa de matuto é bem-vindo quem chegar se tenho as mãos calejadas é do arado rasgando o chão se a minha pele é queimada é o sol forte do sertão sou sou desse jeito e não mudo aqui eu tenho de tudo e a vida não é mentira sou sou livre feito um regato eu sou um bicho do mato me orgulho de ser caipira enquanto alguns fazem guerra trazendo o fome e tristeza minha luta é com a terra pra não faltar pão mesa às vezes vou a cidade mais não sei falar direito pois caipira de verdade nasce e morre desse jeito sou sou desse jeito e não mudo aqui eu tenho de tudo e a vida não é mentira sou sou livre feito um regato eu sou um bicho do mato me orgulho de ser caipira sou sou livre feito um regato eu sou um bicho do mato me orgulho de ser caipira
Chainsaw milling is a lot of fun and I do it as a side job. Next time set up your ladder hang it off the starting end of you log a bit more so you can start your cut easier. It's also a good idea to always use a ladder each cut to help keep each cut as even as possible. Make sure you hold the mill down to the ladder or trees surface to get a consistent thickness of board as well. Get the knowledge needed of how to sharpen your chain properly to give you cleaner faster cuts. Happy milling 👍👍👍👍
That’s great advice, thank you 👍🏼
A friend has a mill but this is the first time I’ve seen one in operation. Nice job Josh
Thank you Al, Josh done a cracking job 👍🏼
I am curious on the FIRST log, how many times did you need to sharpen the chain?
Thank you for the comment Steve. Didn’t sharpen it all the way through, kept its edge all the way through 👍🏼
@@MachineryNation WOW! That is awesome...
Nice One Josh good advice letting the saw cool down me mate had a go at milling some logs after that his new saw needed a engine rebuild🤔 Look forward to see what you make Thanks again
Thank you Darren. Oh sugar, that was not good then ☹️
Excellent video - as always! Well done!
Looking sharp with the PPE get-up!
Thank you Chris 🤩🤩
A great video Josh. Hope to see a part 2! Great reminder to always wear PPE. Cheers!
Thank you Garrett. Part two will be awesome 😎
I plan on giving this a shot with my 80V kobalt chainsaw. Wasn't sure if I should try one of the Amazon mills, but I think it's worth a shot now
time to learn epoy table tops to use the rot to your advantage.
Great set up Josh done a great job for your first time👏👍, i see they sent you a tshirt same as mine got the beer belly affect on the front 😂😂
That’s Nev, it turned out well 👍🏼
Use the on/off bar on the mill for starting and ending your cuts. It is the bar between the front and rear bar on the mill. You want to have it parallel to your cut not pointing up or down when starting. Also do not twist the mill from side to side, slow steady even pressure makes a smooth cut. Practice and pay attention to what you are doing. Very good for your first try though. Good on you to recognize the need to cool the saw down.
Super.👍
Michael Turner
Bucket of water or garden hose will help you inspect the boards
I have seen that, wish we had done it 🤩
Does anyone know if the Husqvarna 455 rancher is good enough for milling?
Sure . Probably only for 12 wide stuff though.
Leave your straight edge on for every cut, otherwise you compound any errors with every slab, get a straight edge with enough overhang for the width of your mill at either end of the log you're cutting to keep it flush at the start and end of the slab. Make sure your rails on the mill are hard down to your straight edge front and back and both sides otherwise you'll get a twisted, uneven slab. Happy cutting, you'll learn heaps just by looking at your process in review and the boards you finish with.
James knock your rakers down. I know it's harder on the saw. But just go slow. 👍
Thanks Dirt Rider 👍🏼
caipira
chitãozinho & xororó
composição: joel marques/maracai
o que eu visto não é linho ando até de pé no chão
e o cantar de um passarinho é pra mim uma canção
vivo com a poeira da enxada entranhada no nariz
trago a roça bem plantada pra servir o meu país
sou sou desse jeito e não mudo
aqui eu tenho de tudo e a vida não é mentira
sou sou livre feito um regato
eu sou um bicho do mato me orgulho de ser caipira
doutor eu não tive estudo só sei mesmo é trabalhar
nesta casa de matuto é bem-vindo quem chegar
se tenho as mãos calejadas é do arado rasgando o chão
se a minha pele é queimada é o sol forte do sertão
sou sou desse jeito e não mudo
aqui eu tenho de tudo e a vida não é mentira
sou sou livre feito um regato
eu sou um bicho do mato me orgulho de ser caipira
enquanto alguns fazem guerra trazendo o fome e tristeza
minha luta é com a terra pra não faltar pão mesa
às vezes vou a cidade mais não sei falar direito
pois caipira de verdade nasce e morre desse jeito
sou sou desse jeito e não mudo
aqui eu tenho de tudo e a vida não é mentira
sou sou livre feito um regato
eu sou um bicho do mato me orgulho de ser caipira
sou sou livre feito um regato
eu sou um bicho do mato me orgulho de ser caipira