Great, did you make the video especially for me? In my wife's Micra, the starter still turns a little when the engine is already running. Thank you for the video, it helps me a lot. 👍👍
Brilliant video. Having only very basic car DIY skills I managed to do this job in 3.5 hours taking my time and a couple of tea breaks using just a basic socket set with long&short extensions, plus a pair of pliers to loosen a couple of hose clips. Could probably do it again in under 2 hours now I know where all the nuts&bolts are. I've got quite long skinny arms and smallish hands which definitely helped in doing this particular job as it's still a bit tight under there despite removing the manifold and air cleaner gubbins out the way. Found it necessary to remove the O/S headlight too for better access which was straight forward enough. Also did this job with the front of the car up on ramps to help my bad back but if you're less than 6'2" this might not be possible. A decent branded no-exchange brand new starter motor cost me 120 quid but likely saved myself well over a ton, probably nearer 2, in fitting charges at the local garage so was well worth doing. Thanks ScrewsNutsAndBolts, subscibed👍
I spend a day on removal wiper motor and underbody work. Turnout in this two ways , you won’t see the starter and if screw is very tight, you still have to do the remove intake from engine because you can’t see and can’t use too much force due to limited space
@screwsnutsandbolts Please I need some advice, I have a a Micra K12, every morning I have to continuously try to start the engine for almost 10 minutes or more before it eventually starts. It cranks but it just never starts up one time even I have driven around a bit that day, I still have the same issue. There is no check engine light on and when the car eventually starts it runs smoothly, engine sounds smooth and very quiet too. Had spark plugs changed but still got the same issue Any idea what could be causing the car not to start at one time and have to keep trying for minutes before the car starts? Thanks in advance for your help.🙏🏽
Bravo ma non serve rimuovere i collettori di aspirazione, il motorino passa a destra, tra i collettori e i tubi di gomma del riscaldamento, scostandoli di poco. Fatto ieri.
Do you know what I wound Have never in a million years though about going in from the top ....Thanks... I have a very very bad issue caused by my mental health. Where I find myself turning the key when the car is running obv this engages & pushes out the rod to which the pinion is attached.. Madness I know ...BUT .the overpowering thought is so strong . I'm a recovering Alcoholic its even more powerful than my cravings for Alcohol where ....sorry for rambling.....
Thank you very much for your NIssan Micra tutorials, they helped me alot!
You're very welcome, thank you very much for the support, I really appreciate it ! 👍👍
Air Cleaner Assembly and Inlet Manifold Removal: th-cam.com/video/49MDOCHRi40/w-d-xo.html
Amazingly good instruction video. I'm not a skilled mechanic, but this video gave me enough confidence to take on this job. Thanks!👍
Thanks for watching !
I'm now now looking at installing an aftermarket cruise control from CANM8
Did you (by any chance) make such a video as well? 😁
@@screwsnutsandbolts
Great, did you make the video especially for me? In my wife's Micra, the starter still turns a little when the engine is already running.
Thank you for the video, it helps me a lot. 👍👍
You're very welcome :)
Does cleaning the starter fix the noise after cranking the engine?
the videos this man dose i have seen many he is verygood and well done fantastic .
Thank you very much!
Brilliant video. Having only very basic car DIY skills I managed to do this job in 3.5 hours taking my time and a couple of tea breaks using just a basic socket set with long&short extensions, plus a pair of pliers to loosen a couple of hose clips. Could probably do it again in under 2 hours now I know where all the nuts&bolts are. I've got quite long skinny arms and smallish hands which definitely helped in doing this particular job as it's still a bit tight under there despite removing the manifold and air cleaner gubbins out the way. Found it necessary to remove the O/S headlight too for better access which was straight forward enough. Also did this job with the front of the car up on ramps to help my bad back but if you're less than 6'2" this might not be possible. A decent branded no-exchange brand new starter motor cost me 120 quid but likely saved myself well over a ton, probably nearer 2, in fitting charges at the local garage so was well worth doing. Thanks ScrewsNutsAndBolts, subscibed👍
You're very welcome, thanks for watching !
Brilliant done my intake gaskets starter motor and clutch at the same time super easy after watching your video’s so thank you. What’s next 👌🏻
Thank you !
Very good camera work thanks
Thanks for watching !
For who worry open the engine, you can take underbody work or wiper motor removal to access the starter
I spend a day on removal wiper motor and underbody work. Turnout in this two ways , you won’t see the starter and if screw is very tight, you still have to do the remove intake from engine because you can’t see and can’t use too much force due to limited space
Is there any easier way to go it than have to take the inlet off ?
It's easier from underneath the car, if you can do that safely.
Top 👍🏾
Thanks !
Super thanks .
@screwsnutsandbolts
Please I need some advice, I have a a Micra K12, every morning I have to continuously try to start the engine for almost 10 minutes or more before it eventually starts. It cranks but it just never starts up one time even I have driven around a bit that day, I still have the same issue. There is no check engine light on and when the car eventually starts it runs smoothly, engine sounds smooth and very quiet too. Had spark plugs changed but still got the same issue
Any idea what could be causing the car not to start at one time and have to keep trying for minutes before the car starts?
Thanks in advance for your help.🙏🏽
There could be a few different issues causing that. Check this link: www.wikihow.com/Car-Struggles-to-Start-but-Runs-Fine
@@screwsnutsandbolts Thank you so much. Reading through now.
Please upload the video for how to replace the glove box for k13. really appreciated.
I don't have access to a K13, sorry
How to replace the starter motor and how mechanical vids should be done
Thank you !
Bravo ma non serve rimuovere i collettori di aspirazione, il motorino passa a destra, tra i collettori e i tubi di gomma del riscaldamento, scostandoli di poco. Fatto ieri.
Yes but it's very difficult to demonstrate the process on video with the manifold in place
ok era solo per aiutare le persone che dovranno farlo ed evitare loro quel passaggio che forse è il più difficoltoso. ciao !@@screwsnutsandbolts
I understand, thank you ! 👍
Do you know what I wound Have never in a million years though about going in from the top ....Thanks...
I have a very very bad issue caused by my mental health.
Where I find myself turning the key when the car is running obv this
engages & pushes out the rod to which the pinion is attached..
Madness I know ...BUT .the overpowering thought is so strong .
I'm a recovering Alcoholic its even more powerful than my cravings for Alcohol where ....sorry for rambling.....
Where is srater motor in Nissan Micra k13
This video should help you: th-cam.com/video/AMTXA-HraGo/w-d-xo.html
🫡🫡🫡