Excellent work as always. They should make the vehicle designers do a year on the repairs, so they understand their responsibility to the poor bastards that have to fix it later. 👍🏴
Hi Kev (stig), ive just replaced the the flywheel and clutch on my citroen xsara picasso 1.6hdi, it wad probably the worst clutch job ive ever done and hopefully the last one i do🤞, I'm getting too old for it👴. Keep up the great work Kev and take care🚘🔧👍🏼
It's like meditation, watching you work, this looked like a pain in the butt, but you make it look so easy for you ( not me) love your professionalism; keep up the good work; I missed your introduction of retrieving your tools from your boxes and setting up, I always like that part of your videos, just saying😊
Thanks for saving me time when I come to do mine Kev. Would love to have seen the whole Jacking up process, the underside of these modern cars are so weak. What is the grease applicator you were using? couldn't find one like it on the net. cheers and keep the brilliant videos coming.
thank you for making this video. ive just done my clutch/DMF. the last time i did a clutch was over ten years ago. this video was able to tell me what bolts i had to remove and for where. it took two and a half days. i near cried , the subframe bolt near the gear box was well rust. took an hour to remove. only problem i have now, is car has its service light on and says - fault, engine repair needed. my mate plugged it in and it shows no codes. he tried to clear the message. does this happen to you?
Excellent work.👏 Help, I have a question... There is an electric plug next to the rear engine mount, is this the same for a 2014 3008 Allure 1.6 Hdi semi-automatic? I did a clutch change and now the engine cranks over, but the car won't start! I can't recall undoing or reinserting a plug near the rear engine hanger! Your help and advice would be much appreciated. 🤫🤞
Bonjour Kévin juste pour te dire à chaque vidéo que je regarde de tes travaux en suis à chaque Foix à en avoir pleins mes yeux car c'est juste grandiose le taf que tu fait et en connaissance de cause tu doit quand même en chier sur certaines voitures en tout les cas encore bravo et surtout pleins de courage pour la suite de tes aventures merci. Sinon à tout hasard à tu des belles remises sur les embrayages complet ??? Si oui je possède une Audi A3 TDI 130cv Quattro 8L de novembre 2001 j'arrive en fin de vie de mon embrayage c'est pour cela car en regardant sur certains sites je trouve que les prix sont beaucoup trop élever surtout des que je demande le kit complet avec le volant moteur, merci à toi par avance si tu pourrez me donnez un prix, bien entendu si tu a des belles remise merci et a bientôt.
I've been watching this, since I need a new clutch and flywheel on my 5008 2.0hdi.. Bet it is the same.. Now I know for sure this is out my ballpark. Cool to watch though!! Nice vid!
@@WMCS Well everyone of them I’ve done, it has one bolt less going back. Straight in the bin. 😄 no need for it. It and the “bastard bolt” at the side of the dpf makes for some fun.
![แฟนแนวใด๋ - ยูริ โตเกียวมิวสิค [OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/4_XVMuhhbsU/mqdefault.jpg)
www.williamsmobileclutch.co.uk 🇬🇧
Submit enquiry for a price and repair date availability.
Thanks for watching and supporting the channel.
This is amazing. The customer gets to see the work being done. You can't see this when your car is in the shop
Excellent work as always. They should make the vehicle designers do a year on the repairs, so they understand their responsibility to the poor bastards that have to fix it later. 👍🏴
They're designed to be difficult to fix
I just made my clutch on a C4 picasso 2011 112CH, to your video. Thank you so much
pretty tough job, fantastic work as always, great episode 😃👍
Big job on the Peugeot, all them bolts and nuts, bet it took less nuts and bolts to build the London eye 👍
That was funny 😆
Great videos I just followed your way of doing the clutch and I did it.. DS4 1.6hdi
Brilliant work as always Kevin, got to love the French way of design, constantly battling with this at work (psa rubbish) lol
That was a big job getting to the clutch
Your just unbelievable how do you remember where everything goes
Attention to detail 👏💪 nice one Kevin 🔧🥷
still cold but sunshine .. already getting better and summer to look forward to, 😊👍
Belta content kev lad, keep it coming 🚗🔧👊
Thanks for the feedback 🍻
Excellent work .
Hi William I just wanted to say you are doing amazing job I love your videos you are hero and just wish you and your family all god
Thanks for taking time to leave a feedback. Much appreciated
you are doing so many i can not keep up with watching the videos but thank you for them a bit dryer for you and it is going to get a bit warmer
them electric ratchets are a god send. saves strain on the hands and also speeds up a job.
Saves at least 2hrs on the job.
Hi Kev (stig), ive just replaced the the flywheel and clutch on my citroen xsara picasso 1.6hdi, it wad probably the worst clutch job ive ever done and hopefully the last one i do🤞, I'm getting too old for it👴. Keep up the great work Kev and take care🚘🔧👍🏼
Glad to hear it ended well. Not a lot of mechanics enjoy tackling the HDI engine.
Really appreciate the feedback. 🍻
It's like meditation, watching you work, this looked like a pain in the butt, but you make it look so easy for you ( not me) love your professionalism; keep up the good work; I missed your introduction of retrieving your tools from your boxes and setting up, I always like that part of your videos, just saying😊
Good work
A friend William, as always, his words for you
gracias siempre por los comentarios y el apoyo.
visitare tu pais algun dia
ok
Thanks for saving me time when I come to do mine Kev. Would love to have seen the whole Jacking up process, the underside of these modern cars are so weak. What is the grease applicator you were using? couldn't find one like it on the net. cheers and keep the brilliant videos coming.
GOOD JOB TANKS FOR DE VIDEO
Great work, the car is needlessly over engineered though. I counted at least 8 bolts holding the battery box.
Excellent video as usual,would you recommend Milwauke Impacts and what model's do you use ?
💪 Kevin
good next week to you my friend 💅
😂😂.. hand manicure
@@WMCS it's going to change clutches you'll see 😂
thank you for making this video. ive just done my clutch/DMF. the last time i did a clutch was over ten years ago. this video was able to tell me what bolts i had to remove and for where. it took two and a half days. i near cried , the subframe bolt near the gear box was well rust. took an hour to remove.
only problem i have now, is car has its service light on and says - fault, engine repair needed. my mate plugged it in and it shows no codes. he tried to clear the message. does this happen to you?
You got a new follower👌 top work. I now own one of these and after doing many clutches in the past I don't fancy this one. Where do you operate from?
Thank you 🤩
super
What a pig that was!
Great vid Kev, you have patience sir!
Excellent work.👏 Help, I have a question... There is an electric plug next to the rear engine mount, is this the same for a 2014 3008 Allure 1.6 Hdi semi-automatic? I did a clutch change and now the engine cranks over, but the car won't start! I can't recall undoing or reinserting a plug near the rear engine hanger! Your help and advice would be much appreciated. 🤫🤞
Lucky you can get that bolt next to the DPF out, on some of these 1.6 HDI's there's not enough space to take the bolt all the way out!
Very narrow and inaccessible on Peugeot. A lot of work indeed. You are a professional
Indeed a bit of a squeeze
Omg what a bloody awful job ,respect to you for just getting on with it
Thankyou
belle video il en a des truc a demonter !!
👏👏👏
What is the part number of central slave cylinder? Is it FTE 1200124? It doesn’t have an O-Ring and you used what type of seal?
👍👍👍
Good job . What grease for the clutch?
Red rubber grease.
Do you travel far in the coutry
What the Labour time on a peugeot 5008 1.6 diesel automated clutch please
Hello . You is genial . what solution do you use to clean the box of that black mess?
Thanks for the feedback. Clutch/ brake cleaner. But any solvent will work just as well.
Greetings from Russia, cool! Also, the radiator needs to be protected from dents.
Thank you .. 🇷🇺 🍻🍻🍻
HOW MANY KILOMETERS the car was ?
Bonjour Kévin juste pour te dire à chaque vidéo que je regarde de tes travaux en suis à chaque Foix à en avoir pleins mes yeux car c'est juste grandiose le taf que tu fait et en connaissance de cause tu doit quand même en chier sur certaines voitures en tout les cas encore bravo et surtout pleins de courage pour la suite de tes aventures merci.
Sinon à tout hasard à tu des belles remises sur les embrayages complet ??? Si oui je possède une Audi A3 TDI 130cv Quattro 8L de novembre 2001 j'arrive en fin de vie de mon embrayage c'est pour cela car en regardant sur certains sites je trouve que les prix sont beaucoup trop élever surtout des que je demande le kit complet avec le volant moteur, merci à toi par avance si tu pourrez me donnez un prix, bien entendu si tu a des belles remise merci et a bientôt.
Thankyou.
Email me your vehicle’s details and I’ll see what I can do.
I've been watching this, since I need a new clutch and flywheel on my 5008 2.0hdi.. Bet it is the same.. Now I know for sure this is out my ballpark. Cool to watch though!! Nice vid!
Very Nice Job!!!! How much for this repair??? Thks
www.williamsmobileclutch.co.uk
Est-ce qu’il faut dévisser tout le berceau?
Yes as per video
To my US eyes that was a strange looking flywheel?
Y el aceite
👍👍👍👍👍👍🦾🦾🦾🦾
That one bolt for the battery tray coming from the inside of the arch, it’s only purpose is to piss the mechanic off😄. Like why would they do that
Honestly 3 bolts 10mm would have been enough. But 5 x 13mm bolts with a torx bolt and one in the wheel arch. Now that is some French garlic bread 🧄 🥖
@@WMCS Well everyone of them I’ve done, it has one bolt less going back. Straight in the bin. 😄 no need for it. It and the “bastard bolt” at the side of the dpf makes for some fun.
@@WMCS
hello Kevin
garlic bread in french "frotte a l'ail" with olive oil 👍
@@kmcca08 that bolt is easy compared the one behind the starting motor worse.
Bravo