Make DIY Boost converter 3.7v to 12v, Step up voltage adjustable converter
ฝัง
- เผยแพร่เมื่อ 10 ต.ค. 2023
- Make DIY Boost converter 3.7v to 12v, Step up voltage adjustable converter.
( 3.7v to 12v inverter )
This is a very good simple Boost converter circuit and you can apply an LED tester circuit. Good luck to you. Simple Electronics projects.
Inductor: 2.5 cm Diameter ferrite rod
Components used in this project:-
1. Irfz44n or Irf305 MOSFET
2. 220 Ohm / 2w Resistor
3. 2200uf/35V Capacitor
4. Inductor
5. 2A Diode
6. 10K Potentiometer
#makebuckconverter
#boost_converter
#dcstepupconverter
#homemade101
#buckconverter
#3.7vto12v
Thank you very much bro❤
Its working very well🎉
I made a super bright emergency light with this💖💖👍👍
welcome bro thank you.
Good job 💥🤟🤟 ...thanks for shearing 🙏💛
welcome
1 st good video and experiment
welcome and enjoy
Good but amp.kaise badhaye.please reply.
5A
Hi again, I have 0.6mm of wire. How many turns i can use for the inductor?? Thanks for allí. Great proyect
40 runs all 20T 0 20T
Very nice video ! Can you please show how to make 12v to 48v to make work inverter from battery. Thanks.
ok i will try
works great! BTW, i was wondering, if I use a lower trigger voltage MOSFET, would it be capable of stepping FROM lower voltages? say, 1-2.5V?
Yes you can!
Ye circuit kitna der Tak chal sakta hai
If dc input 0.5 volt - 2 Volt DC, what is component can i use for booster converter?
2v ok yes
HI, I could use other transistors like H22 13866 or P133009 or LT5250 or SB3040PT or RC3009 or MOSFET S20C45C instead of irf3205 ??, thanks so much in advance.. best regards!
can't. MOSFET only.
OK, only mosfet, but I can use MOSFET S20C45C? thanks again.
Can I use 4700uF 16v capacitor ,IRF3205 mosfet and 1N4007 diode for this?
yes. but not recommend Diode and capacitor voltage
Hi, what Is the section in mm of the wire to create the inductor?? And the diammeter of the toroidal ?? Thank you
Can you tell me the diammeter of the wire and the toroidal to create the inductor??
1mm, 2cm
@@homemade_101 Ok, if i use for example 0.6mm i need to reduce the number of turns or not??
can I use a 10A10 or MUR1540G for the diode?
ok
could you pls tell me why is there background noise when the boost is working, where is the sound from and how to decrease the noise ?
it is normal. induction sound
What Is the value in Henry of the inductor?? Thanks
0.11mH 0.3 Ohm
Thank
Can I use 10 k trimpot instead of variable resistor
ok
Hola lo hize exactamente igual pero mi transistor se calienta y qué será lo que esta mal?
G-S connect 10K resistor and use heat sink
@@homemade_101 gracias ya funcionó perfecto 👌 un chingon eres hermano✌️👍
Where is that hissing sound coming from. From Capacitor or Inductor?
it is inductor
@@homemade_101 Can I supply this circuit with 5vdc if i don't have the 3.7vdc?
yes 5V ok @@century_centure
The guy who had 68v on the 35v capacitor was lucky that the capacitor didn't explode, put a higher voltage on the capacitor and if the coil squeaks, it means that it is very loaded and the coil probably has too low a maximum current, if the coil gets hot, change the coil
Nicely done 👍 how do I make one to convert from 5v to 12v thanks in advance ❤
Please wait
@@homemade_101 ok thanks
And can it work with 5v direct from 5.5v Solar panel? Kindly reply to this please.
yes
@@homemade_101 I can see you have already answered my question. Thank s alot Bro.
Chào bạn.video rất hay.ban cho tôi hỏi đầu vào dung điện đc 12v được không? Xin cảm ơn!
dùng tụ điện 35V
its not working bro 😢 me banaya ye nahi aa raha output bass 3.30V input deta hu to 3.40V Output hi milta hai potentio ko gumata hu fir bhi not work
This is working well. change inductors and mosfet
@@homemade_101 kitne size ka inductor use karu
Nice video 👍, can you give the circuit diagram? And I want to ask, how many winding the inductor? Thank you
Please wait
drive.google.com/file/d/16eFvt-oyOp4ul343Uy-lTJ4bbMdWeu8l/view?usp=sharing
Hello bro can you make h bridge circuit that convert 310dc to 220v Ac plz
I haven't idea it. I will try
can i use z24n or 2x z24n ????
yes you can use
@@homemade_101 1x z24n ??? ... BUt thank you so much
its boos the amp ?
5A
Use more than one capacitor bcz when the load is higher the voltage drop at 3.7 again
THANK YOUR ADVICE
@@homemade_101 Welcome 😊
is me 12V 1.5AMP input to 12V 5 AMP output circuitdiagram milega sir
No no. 3.7v to 5v input
@@homemade_101 sir ye work hi nahi kar raha kya karu 3.7 V input deta hu to bass 3.4 hi output aata hai ic bhi sahi hai fir bhi sir
Ok ❤
enjoy
Good video, you can share the diagram
OK i will send tomorow
Circuit diagram 👉 drive.google.com/file/d/16eFvt-oyOp4ul343Uy-lTJ4bbMdWeu8l/view?usp=sharing
@@homemade_101 thanks bro
Ok cuon cam khu nhieu tot......!
thank you
Diode ka name kya hai
1N5401
How many amps output
5A
How many henery inductor brother
30uH
@@homemade_101 will a 5millihenery work i salvaged it from old cfl driver circuit
Max current?
5A
@@homemade_101 thanks.
Маленькая сила тока. Мне больше вот эта схема нравится: th-cam.com/video/S_WAZnX_v94/w-d-xo.html
I will just buy 2 more batteries 😁
it is no problem 😉
Inductor value
0.12 mH
How many amp
5A
Working volt 2200uf 35V step up 60V DC danger❗ of kapasitor
no, this circuit is safe. use a switch
60v cannot give full illumination to the 12v car lamp...😁😁😁
yep
Y it make noise... ?????????😮😮😮😮😮😮😮😮
it is norml
Kepala sangat sakit lihat vidio ini karena terlalu cepat bagi saya pemula.
😮💨
Bo loc thanh........?
🤔
генерация срывается , не показал как мотать в какую сторону и каким проводом . нет стабилизации на выходе . схема отстой! ! ! !
what bro
Adjustable power Supply: th-cam.com/video/1tJxmAp36Cg/w-d-xo.html
Can it give constantly output 12volt 5a in small load
@@howtomakemoneyonfacebookpa2747 yes try
No Good, Where is schematic
this is a very simple circuit.