@@chinmoy1955 the voltage ⚡ will definitely go down, from 60v to probably 8 or 10 volts once the circuit is loaded with a bulb, so no worries about feeding 60volts to a 12 volt lamp
Nice converter it's a pity about the frequency admits because I want to run my transistor amplifier from it I've got some i r f mosfet transistors I must give it a go
If this is a 3.7 volt to 12 volt DC-DC Boost Converter why isn't the Output voltage fixed at 12 V. I need to make an exact replica of this for my Power Electronics Course project. Also, what is the rational behind using a potentiometer? Please answer the questions. Thanks a lot!
Simple boost Converter : th-cam.com/video/ynJ_Pf5rRnk/w-d-xo.htmlsi=tzBZ9gn_hfGLNdXZ
Well done. Thanks. I suggest that a smaller value MOSFET might be used to drive an NPN transistor that is capable of conducting more current.
.33 5watt. no need 1ohm or 4.7ohms 1/4 watt resistor enough for gate drive...
Very nice project
thank you bro
Please connect the loads and measure the voltage. Is it advisable to feed 60V DC to a 12V lamp or 12V LED?
I did it
@@chinmoy1955 the voltage ⚡ will definitely go down, from 60v to probably 8 or 10 volts once the circuit is loaded with a bulb, so no worries about feeding 60volts to a 12 volt lamp
I have 5-19v 3A input I need 22v constant output. How can I achieve it?
What material is used to build that inductor ?
Can I get 5v 4A by feeding 5v 1amps through this
I think can't
bro, Why is the noise from the circuit?
Will it give a constant 12 volt output, when I connect load? please reply
It is induction sound in inductor.
@@homemade_101 thanks
My input is not fixed it may be 3v or less than 3v so,is this circuit work ? Which value of components i have to used ?
try it
Can you please tell me how is the MOSFET switching in this case without a PWM signal ?? Thank you !!
no pwm
@@homemade_101 so how does the MOSFET change it's switching state ?
Thise MOSFET are switching at high frequency,I think it's 300khz
Marvelous video of boost converter. But how to make that inductor. How many tiens are there and which gauge wire is used?
0.12 mH. 6T 0 6T . 0.5mm copper wire
Nice converter it's a pity about the frequency admits because I want to run my transistor amplifier from it I've got some i r f mosfet transistors I must give it a go
does the potentiometer lower the voltage output? i only need 24v for a pneumatic solenoid valve. thank you
no it was use frequency control
Can it be used with a 6v solar panel to charge the 12v battery?
I think can't bro, but try
If this is a 3.7 volt to 12 volt DC-DC Boost Converter why isn't the Output voltage fixed at 12 V. I need to make an exact replica of this for my Power Electronics Course project. Also, what is the rational behind using a potentiometer? Please answer the questions. Thanks a lot!
frequency adjusting in mosfet
Use zener diode to get fix voltage
6:58 electro boom is proud
yeop
wow nice video bro
Welcome bro
que funcion tiene el segundo transistor ?. al final no conectaste el pin central
🤔
Can i use this to run a 6volt 15 watts fan?
yes bro. try
@@homemade_101 ok, thanks
Hi. What is a good resistor to use if im not using any pot?
5K, 10K, 50K
It would work with 3,2V 280 Ah lifepo4 battery?
yes
Nekem is működik ..😊😊😊
👍👍👍👍
good luck thank you
Nice 😍😍😍 highly appreciate this ❤😊
Enjoy
Can this work without the pot?
can't but try it
Can it spot weld lithium battery?
yes try it
Very nice
thanks bro l
How to change this circuit to buckboost
this is boost
@@homemade_101 how change to buck-boost? I need this ! :D
No voltage measurements?
🤔🤔
Please, i need simple buck converter from 12 to 5v like this circuit.
this is good; th-cam.com/video/PFQj7pmjCM0/w-d-xo.htmlsi=LY30hB7f5e7f2vUY
thank you bro
You're welcome!
Super proyecto profesor
thank you
Inductor value ?
0.12 mH
Will 12V,100w filament bulb glow brightly??
Reply must
mm try
can i run 20watt speakers using this boosted voltaage ?
yes. but not recomnded
@@homemade_101why and what’s the solution?
@@suvamkumarnayak you have 12 volts but not the current
That Good and Number one for you ❤❤❤
thank you bro, enjoy
I will make it today
good luck
how many volt without pot
i don't know it is 🤔
Can I use this to make 3.2 V to 5v using 5v zener and use in pam8403 amplifier board...?
not recommended
How to increase its current
it is depend mosfet and inductor
Nice One Boss👍👌 But@6:59.......Oops, careful🙆😮😅
Thank you bro. It had to mistake 😁
Can use for 12 volts 30a li ion battery’s charging sir?
No. this is not a charger
Sir kitna watt max hai or phone charge hoga❤❤
50W
@@homemade_101 mobile charge ho jayga
@@dconstars not recomnded
How long will this battery 🔋 last? Mean 1 minute, 10 minutes?
5mi
👍👍👍😊
☺
👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼
❤
Does the bulb glow with full brightness??
Reply must❤
yep
😂👍👍👍
😌😌
Sir koi aisa boost converter batao jisse 12 amplifier aram se chal sake and nice Video Sir 👌
I think it is dangerous. because noice genarate
this is generating high frequency audio noise i can hear it
yes bro
What is making that sound
induction sound in inductor
Okay
Does it generate any heat? I am tryna work it out for a circuit
Kya ye sach me kaam karega
w
😂❤🎉
Hello
yep