Hey I just repaired my head gasket for $60 with Nulon Permanent head gasket and block repair. Fantastic. Just like a new one again! I had the dreaded water loss and vapor lock on staring, it was that bad.
@@macgyver2615 do you have to tighten them in a sequence? Or just do your best to tighten them all evenly, I got them in but a bunch ended up with no movement and I wasn't sure if that's normal
@@Sco33a101 any order but the valve has to be closed so then you know the exact gapping.. if there is no gap you will wear them out too quick / or valve wont fully shut, specially when they get hot as metal expands.
Hello sir I have question about 4.5L nissan patrol I have temperature issue car overrheat after 140 and 160 till 120 temperature fine I change the engine also loditer too many things but still same problem engine heat over 140 can you pls explain what's the reason 🙏
hello, I'm from Russia. I also have the Nissan Safari TB45E of 1998. Can you please tell me you are removing the nozzle connecting the throttle and the air filter branch to 0: 39-0: 42 seconds ... it's not your original where to buy it? my tore
Tighten cylinder head bolts in numerical order. I Tightening procedure (1) Tighten all bolts to 29 N×m (3.0 kg-m, 22 ft-lb). (2) Tighten all bolts from 57 to 67 N×m (5.8 to 6.8 kg-m, 42 to 49 ft-lb). (3) Loosen all bolts completely. (4) Tighten all bolts to 29 N×m (3.0 kg-m, 22 ft-lb). (5) Turn all bolts 69 to 74 degrees clockwise or if angle wrench is not available, tighten all bolts from 64 to 74 N×m (6.5 to 7.5 kg-m, 47 to 54 ft-lb).
Great vid and no fucking music, well done.
Hey I just repaired my head gasket for $60 with Nulon Permanent head gasket and block repair. Fantastic. Just like a new one again! I had the dreaded water loss and vapor lock on staring, it was that bad.
Where was the cam chain? Is this a push rod engine? If so, what an old reliable beast!
Rods
Great video. Thanks for posting.
Do you have to tighten the tappet bolts in a certain way to ensure correct installation?
Yes, make sure you have filler gauges and leave the exact clearance.
@@macgyver2615 do you have to tighten them in a sequence? Or just do your best to tighten them all evenly, I got them in but a bunch ended up with no movement and I wasn't sure if that's normal
@@Sco33a101 any order but the valve has to be closed so then you know the exact gapping.. if there is no gap you will wear them out too quick / or valve wont fully shut, specially when they get hot as metal expands.
Hello sir I have question about 4.5L nissan patrol I have temperature issue car overrheat after 140 and 160 till 120 temperature fine I change the engine also loditer too many things but still same problem engine heat over 140 can you pls explain what's the reason 🙏
I need timing of crankshaft and to distributor
hello, I'm from Russia. I also have the Nissan Safari TB45E of 1998. Can you please tell me you are removing the nozzle connecting the throttle and the air filter branch to 0: 39-0: 42 seconds ... it's not your original where to buy it? my tore
Thank you m8, that helped me a lot..
Where did you get the bolt pattern sheet and the torque specs from?
They normally come with the head gasket kit..
Tighten cylinder head bolts in numerical order.
I Tightening procedure
(1) Tighten all bolts to 29 N×m (3.0 kg-m, 22 ft-lb).
(2) Tighten all bolts from 57 to 67 N×m (5.8 to 6.8 kg-m, 42 to
49 ft-lb).
(3) Loosen all bolts completely.
(4) Tighten all bolts to 29 N×m (3.0 kg-m, 22 ft-lb).
(5) Turn all bolts 69 to 74 degrees clockwise or if angle wrench
is not available, tighten all bolts from 64 to 74 N×m (6.5 to
7.5 kg-m, 47 to 54 ft-lb).
you can get the service manual CD of ebay tells you everything... worth getting it.
How long did the whole job take?
About 3 months (no rushing it)
Y61.year?
1999
@@macgyver2615 👍my y61.2008.tb 45e
@@macgyver2615 how many km did you get out of the tb45? I've just hit a million
@@BiGsesk only about 400.000. Now it has a LS2 V8
@@macgyver2615only 400? Did it blow up or did you just decide to swap anyway?
ممتاز 😍👌