ฝัง
- เผยแพร่เมื่อ 10 ก.ย. 2024
- #MrNams
Subscribe: goo.gl/mqbdai
Facebook: / mrnamsofficial
Twitter: / mrnams
Hello friends,
Hope you all doing well!
This video will demonstrate how to repair Popcorn Maker Machine which does not work at all .
A popcorn maker (also called a popcorn popper) is a machine used to pop popcorn. Since ancient times popcorn has been a popular snack food, produced through the explosive expansion of kernels of heated corn (maize). Commercial large-scale popcorn machines were invented by Charles Cretors in the late 19th century. Many types of small-scale home methods for popping corn also exist.
Commercial popcorn machines are commonly found in movie theaters and carnivals, producing popcorn in a pan of hot oil, which has approximately 45% of its calories derived from fat. Hot air popcorn poppers appeared for home use in the late 1970s, which produce popcorn with only 5% of its calories derived from fat.
In this video, I have repaired small Hot-air electric popcorn popper.
An electric popcorn popper is a small electric appliance designed for heating kernels of popcorn to the point where they pop into an edible form. Hot-air poppers have a fan-like impeller that agitates the kernels with a turbulent stream of hot air in the popping chamber.The heat is generated by a heating element in the base, activated by a simple on-off switch and controlled by a thermostat. It include a motor to rotate fan. The heating element is spring like resistance coil.
What Can Go Wrong with a Popcorn Popper?
A faulty thermostat or thermal cut-off is often the cause of common popcorn popper problems such as scorched or unpopped corn and excessive popping time.
In this video, I have shown,how I find out fault and fixed it.
Very common fault is "Blown Thermal Fuse"
What Do I Need for Popcorn Popper Repair?
1) Screwdriver
2) Needle Nose Plier
3) Multimeter
4) Solder Iron
5) Wire Stripper & Cutter
6) Solder Wire
Watch video for detail Steps to Repair it
Watching this video you might understand
1) How to disassemble a hot-air popcorn popper
2) How to assemble a hot-air popcorn popper
3) Ho to replace Thermal Fuse
4) How popcorn machine works
5) Hot-air popcorn popper repair
6) Hot-air popcorn popper sound
7) Understanding parts of Hot-air popcorn popper
8) How to use screw driver
9) How to unscrew
10) How to use Screwdriver
11) How to use Needle Nose Plier
12) How to use Multimeter
13) How to use Solder Iron
14) How to solder
THANKS FOR WATCHING.
If you enjoyed video, please do like, share and comment.
Please SUBSCRIBE to follow new Uploads goo.gl/mqbdai
WARNING:
Always be safe, everything you do is at YOUR OWN RISK!
I shall not be liable for any injuries, loss or damages claimed to be caused by watching the contents either.
#mrnamsofficial
#instagram
#reels
#instagood
#craft
*Click below link to subscribe,it's absolutely free.*
*goo.gl/mqbdai*
*सब्सक्राइब करण्यासाठी वरील लिंकवर क्लिक करा,ते पूर्णपणे मोफत आहे.*
*सब्सक्राइब करने के लिए ऊपर दिए गए लिंक पर क्लिक करें, यह बिल्कुल फ्री है|*
Thank you very much. Your video has allowed me to restore life to my 1980's popcorn pumper.
Great
Would solder not potentially melt at the temperature these things run at? Had the same issue with mine but chucked it out when I saw the fuse was rivetted rather than soldered.
Completely agree,but i did not have rivet gun and its really hard to remove existing rivet, till now it works fine
Thanks a lot. I have an old Hamilton Beach popcorn pumper pp01. It started overheating and not spinning. Does the fuse have anything to do with the fan's work? The machine is 220V, 1250W, 50Hz, what fuse should I look for?
No,in your case heating element is working, try to check if motor is working or not or if it working then check for propeller, some time due to heating motor spins but propeller slips
@@MrNams thanks a lot. Can I assume that if the motor made sound the last time I turned it on it works and the issue is with the fan? I assumed the sound is due to friction between the motor and shaft. Unfortunately I cannot seem to find anyone who has a video of my specific model disassembled.
If you able to disassemble your self then please do it, it very easy, ***but but remember to unplug before dissembling it**.
Very useful info, the internal circuitry is common to many chinese popcorn makers aesthetically very different from this, as the vintage looking Smart and Ariete.
thanks
what is the name of the paper that is rolled up inside the motor, I broke it somehow, and now need to look for a replacement.
temperature resistant mica paper
Hello, I have a Champion CHPCM110 Popcorn Maker. After a year and half in use, it stopped mid-popping and now it won't turn on any more. Perhaps the same applies here, it could be the fuse? I use it mainly to roast coffee, so my warranty is out the window. Thought I could follow your demo and try looking for a new fuse to replace with but I don't know what it uses. Haven't disassembled it yet.
On the bottom it says 230V~50/60Hz / 1200W. Anything else I should be able to know based on this? Much obliged if you happen to have an advice. Cheers.
Go ahead and disassemble it with proper safety.
I have a problem with a thermal fuse also.
But in addition, the fan is also doesn't spinning. When I connected it directly to DC supply it works.
What would you recommend to check ?
ohh, did you see any burn component?actually nothing complicated here, just convert 230ac to 12dc(i forget its 12 or 24)
@@MrNamsit's 24
This a Pigeon 1200W maybe? What fuse should I get? Which temperature and ampere? I have this same model popcorn maker, and thermal fuse burned. I'm not able to read the text on the fuse...
AUPO BF216 216C
@@MrNams Thank you very much! Btw, oops, just noticed mine machine says 1100W but I guess that BF216 216C do just fine it also? Not sure why it's 1100W... could it be that the wall outlet voltage in my country is 230V ?
I feel AUPO BF216 216C should work fine
My pop corn machine heating element is fried where can I get replacement
Try any local electronic market in your city.
I tried no luck
Try this
amzn.to/3pam28B
My popcorn machine runs okay for half a minute but then the inside gets heats up and become bright red as its going to catch fire… Can you tell what the issue its facing?
Hi. Thanks for sharing.
My popcorn popper seems to be heating but the motor is not spinning at its maximum.
I noticed that because the noise and air flow has decreased.
Any idea what is wrong?
Thanks
may be you need to clean holes of aluminum container
Hi, Thanks for the video. My fuse is blown and it is an AUPO BF216 216C . Can i use any 10amp 250v thermal fuse? will 142c suffice as advised by you?
cheers
I feel 142c is not sufficient, it will blow immediately, its better to have at-least 216c or higher,It has thermal cutt-off to protect over heating.
Aupobf216216c
The Fan (blades) of my team melted with an overheating ... Can I replace it with the Fan of an ATX Power Supply of a P? ... Thank you!
Same with me,I tried lot but could not get Fan. If Fan of an ATX Power Supply fits then why not? Please update once you do that, thanks in advance.
@@MrNams The idea is not to use the complete fan but the blade, only the blade of this one because the diameter allows it.
Another question: If the consumption (at startup is a little higher) is 10 amps (1200 Wats / 120 V = 10 A, in the case of my country) ... Why is a 10A thermal fuse used? ... Doesn't this one melt by that current to the limit only at startup? .. Thanks again ..!
1) Fan: Yes I am also on same page, we should use only fan blades
2) Fuse: I think this is fault, and applicable to all countries, initially I changed few fuses, and finally i did connect directly without fuse, and relied on "Thermal Switch" to cut power on over heating.
Hi, nice video. What about the thermal protector? Do you know if it is 150c?
AUPO BF216 216C
@@MrNams Tks!
Do you know if the thermal cutoff switch is 160c?
I think around 190oc
Tks!
can you provide a link for the type of fuse you used?
www.amazon.com/250V-Celsius-Circuit-Temperature-Thermal/dp/B00JR5ED7U/ref=br_lf_m_pz5u4gzn28wt7we_ttl?_encoding=UTF8&s=hi
@@MrNams Good evening and cordial greetings: If the power of my equipment (Popcorn Making Machine) is 1,200 Watts and its nominal voltage is 120 VAC and being 98% Resistive Load the working current is then 10 Amper .. How to protect it with a thermal fuse of 142 ºC / 10 A / 250 VAC? ..... That If = 10 A is which? Note that the work current or steady state is equal to that specified in the "screen printing" on the fuse body. I ask: Shouldn't it be greater ?, say 15 A because in that case with any variation to the increase in the line voltage will increase the current will be that the fuse blows? regardless of temperature. Could you clarify this reasonable doubt for others? Thank you!!
I've a vintage Presto hotair popper that has poor performance. Unpopped kernels are the norm. Extended run times have heat-warped the clear plastic top. Please share how I can solve these probs.
Don't it have thermal cutoff? Its dangerous if it don't have.
Presumably the popper has a cutoff switch. Obviously a heating device without one is a fire hazard. Do these switches often deteriorate?
can i know, how much voltage operate the motor and heating element?
18V the motor, 230V the heating element.
yes, thanks for answering
@@MrNams One thing you have to keep in mind: Most manufacturers use a bridge rectifier spanned on two points across the heating element which they use as a voltage divider in order to power the blower motor without using a transformer. You can see them on hair dryers on the hair dryer's pressure side located on the back of the fan motor.
@Bandicoot803 Thanks for valuable information.
ये पोपकोन मेकर मे थँमल फ्युज कीतने नंबर का लगाना चाहिए
AUPO BF216 216C
Hello sir. I would ask about my popcorn maker. I only replace capacitor and the fuse. But the heat that the coil produces is hotter than the normal. Hope you would help me about this problem. Thanks sir
Is capacitor of same capacitance? also check thermal fuse same, other wise it may not cut power even temperature is high.
I didnt check it out but i only give it to the electronics shopwner to replace it
May be they have replaced with higher temperature rated fuse.
The newly replace one is 240°C 10A 240V i think? Im not sure for the voltage cause its blurred
HELLP, I didn’t know, I couldn't use normal salt, and yes I used it and now my machine makes by g smoke and help me is it broken? My mom is gonna kill me.
there should not be any problem to machine unless you use liquid, that smoke may be because of salt,clean with cloth and it should work well
@@MrNams oh god, i used oil
😀
Yeah, I'm just gonna buy a new one instead.