Hey! Your videos are FANTASTIC! I recently followed your steps because my hot tub kept tripping the breaker. I unhooked the element, voila, it stayed on so I changed the element. I set my temperature like normal. However, now it’s heating EXTREMELY slowly. I’m talking 12 degree increase in about 48 hours. What steps would you recommend to diagnose that?
Change the sensors. Temp sensor is covered in calcium or about to go. Thats if the right element was installed. EG. 4kw or 5.5kw. Also. Whats the volts coming into the hot tub?
@@VIPPoolsandSpas apologies, i didn’t see the rest of your comment. It’s 240V. And it’s the same element type that came from the factory, so it should be correct
@@VIPPoolsandSpas update: got the sensors cleaned off and reinstalled! I have the tub running, it started at 75 degrees and hasn’t increased any in an hour. When I turned on the power, the heating light was blinking and then it turned solid. When that happened, I did hear something in the power pack click. The hot tub continues running normally from all I can tell. Any suggestions for anything else that might be going on?
Excellent video. Great info. Would like to understand more control board issues, trouble shooting and repair, solenoid testing and replacement along with temperature sensors and relationships to control boards and possible error codes being displayed on different types of control board displays. Thanks brother, keep up the good work. 🙂😎
A lot of times I know it's the board but can't pin point it where. Normally I get a computer repair guy to fix some of my stuff or test it. I should get a electronics guy to test things and record it. I don't have the skills to tackle the electronics repair.
The hot tub was heating fine before I drained all the water out to clean the hot tub after I fill the back up. All the pumps are working but not heating up now!
For some reason i get no red light on the dash light its not calling for heat and its only gettin 120v to the heating element ive tested everything besides the board ?? Think thats my issue no codes
Hi, I have a question. My tub recently stop heating. Everything look normal. No code and motor working fine on both speed it just not heating. I checked the filter and nothing else is broken. Where do I need to look?
Chasing my tail with my tub. I can turn the tub off at the breaker, turn it back on and it will heat up to a chosen temp of say 98. after this initial heat-up it will not heat again, until I shut the power off at the breaker and start the process again. The fact that it will heat leads me to believe the element is fine, but maybe a relay is bad or something else on the board not communicating to heat again..
@@walterstrikes it was a relay on my circuit board that would not close the loop to allow the heater to produce 240v. Unfortunately my boards are obsolete so I retrofitted the board and heater with a Balboa BP7 bundle.
On my Hot springs hot tub the code for the pressure switch came up. It stopped heating. I jumped the pressure switch the red light on the board came on but the hot tub still doesn't heat. What do I try next?
My hot tub isn't heating. On the display board if I hit the cool button to turn it down it automatically goes back up. And stays at 104. So it shouldn't do this?
plug and play dream maker spa heating up verrry slow 2 days and only at 80* filter flap door at the top of the skimmer should I blast the hose down the skimmer to clean it? .filter is fairly new. thx
@@VIPPoolsandSpas no, city I hear it turn off when I reduce the temp. I have at st .. not sure if it's stuck on ec cause when I check it starts at ec I've blasted the hose in each jet to eliminate air pockets... 🤔
@@cheromilli2681 normally if its on economy, the temp gets around 80-85. Could be on that. do you know how to change it? What spa pack (what everything plugs into) do you have? Balboa?
@@cheromilli2681 remove the door of the spa pack and there should be red and white dip switches. I think its #7 you can change it to just standard mode. SEE BACK OF DOOR FOR DETAILS.
i replaced heat element, checked for air locks, i have voltage at the element. and if you shut valves on the union to heater, it gets hot. At the filters their is no sucking . pressing jets 3 on immediately cuts the heating symbol off. no error codes. any advice greatly appreciated
![Removing a HOT TUB Heater Tube [ TIPS and TRICKS ]](http://i.ytimg.com/vi/JLcy2tJ6odI/mqdefault.jpg)
![Removing a HOT TUB Heater Tube [ TIPS and TRICKS ]](/img/tr.png)
Make sure to check out our other videos.
Hey! Your videos are FANTASTIC! I recently followed your steps because my hot tub kept tripping the breaker. I unhooked the element, voila, it stayed on so I changed the element. I set my temperature like normal. However, now it’s heating EXTREMELY slowly. I’m talking 12 degree increase in about 48 hours. What steps would you recommend to diagnose that?
Change the sensors. Temp sensor is covered in calcium or about to go. Thats if the right element was installed. EG. 4kw or 5.5kw. Also. Whats the volts coming into the hot tub?
@@VIPPoolsandSpas thank you so much! We do have extremely hard water and that makes perfect sense!
@@VIPPoolsandSpas apologies, i didn’t see the rest of your comment. It’s 240V. And it’s the same element type that came from the factory, so it should be correct
Take the sensor out and put in some cleaning vinegar.
@@VIPPoolsandSpas update: got the sensors cleaned off and reinstalled! I have the tub running, it started at 75 degrees and hasn’t increased any in an hour. When I turned on the power, the heating light was blinking and then it turned solid. When that happened, I did hear something in the power pack click. The hot tub continues running normally from all I can tell. Any suggestions for anything else that might be going on?
Excellent video. Great info.
Would like to understand more control board issues, trouble shooting and repair, solenoid testing and replacement along with temperature sensors and relationships to control boards and possible error codes being displayed on different types of control board displays.
Thanks brother, keep up the good work.
🙂😎
A lot of times I know it's the board but can't pin point it where. Normally I get a computer repair guy to fix some of my stuff or test it. I should get a electronics guy to test things and record it. I don't have the skills to tackle the electronics repair.
The hot tub was heating fine before I drained all the water out to clean the hot tub after I fill the back up. All the pumps are working but not heating up now!
This is very common. Test your heater element. AND. Make sure you don't have an air lock.
For some reason i get no red light on the dash light its not calling for heat and its only gettin 120v to the heating element ive tested everything besides the board ?? Think thats my issue no codes
120v at the element sure sounds like a heater relay.
Hi, I have a question. My tub recently stop heating. Everything look normal. No code and motor working fine on both speed it just not heating. I checked the filter and nothing else is broken. Where do I need to look?
Test the heater
Chasing my tail with my tub. I can turn the tub off at the breaker, turn it back on and it will heat up to a chosen temp of say 98. after this initial heat-up it will not heat again, until I shut the power off at the breaker and start the process again. The fact that it will heat leads me to believe the element is fine, but maybe a relay is bad or something else on the board not communicating to heat again..
Could be a sensor issue. Your heat sensor maybe.
i have the same issue. Any solution yet?
@@walterstrikes it was a relay on my circuit board that would not close the loop to allow the heater to produce 240v. Unfortunately my boards are obsolete so I retrofitted the board and heater with a Balboa BP7 bundle.
On my Hot springs hot tub the code for the pressure switch came up. It stopped heating. I jumped the pressure switch the red light on the board came on but the hot tub still doesn't heat. What do I try next?
is the circ. pump running? whats the problem? Is there an error code?
My hot tub isn't heating. On the display board if I hit the cool button to turn it down it automatically goes back up. And stays at 104. So it shouldn't do this?
It's the topside. Need a new one. Fix that first. Could be another issue besides that.
@@VIPPoolsandSpas I wanted to thank you. That fixed it. The tub has been sitting for a couple years and everything else works fortunately.
@@chelmjustice1226 glad it worked out.
plug and play dream maker spa
heating up verrry slow 2 days and only at 80* filter flap door at the top of the skimmer should I blast the hose down the skimmer to clean it? .filter is fairly new. thx
do you have well water?
@@VIPPoolsandSpas
no, city
I hear it turn off when I reduce the temp. I have at st .. not sure if it's stuck on ec cause when I check it starts at ec
I've blasted the hose in each jet to eliminate air pockets... 🤔
@@cheromilli2681 normally if its on economy, the temp gets around 80-85. Could be on that. do you know how to change it? What spa pack (what everything plugs into) do you have? Balboa?
@@VIPPoolsandSpas dreammaker ezspa
not sure why it stays on ec when I change it
🔺️ st
@@cheromilli2681 remove the door of the spa pack and there should be red and white dip switches. I think its #7 you can change it to just standard mode. SEE BACK OF DOOR FOR DETAILS.
Do some tubs not have a pressure switch?
Yes
i replaced heat element, checked for air locks, i have voltage at the element. and if you shut valves on the union to heater, it gets hot.
At the filters their is no sucking . pressing jets 3 on immediately cuts the heating symbol off.
no error codes. any advice greatly appreciated