How to Replace Transfer Case Shift Motor 01-02 GMC Sierra 2500 HD
ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- 1A Auto shows you how to repair, install, fix, change or replace a transfer case shift motor that is not working, engaging or is defective. This video is applicable to Chevy Silverado and GMC Sierra models.
Get more tips & tricks when you subscribe to our channel!
1aau.to/m/Subsc...
Buy Now at 1AAuto! 1aau.to/ia/1AFW...
Connect with us on social media!
1aau.to/m/Facebook
1aau.to/m/Twitter
1aau.to/m/Insta...
Check out this playlist for more great tips and tricks! • Tips & Secrets only Me...
#1AAuto
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I have a 98 3/4 Chevy it goes into 4x4 high but does exactly what yours is doing into low, it tries then goes right back to high range. Would that be the same problem most likely?
It's not that bad of a job if you take your time. Thanks for watching. 1aauto.com 888-844-3393
Thanks for watching. Have a great day! 1aauto.com 888-844-3393
You may want to inspect the gears in the transfer case. Hope this helps you out. 1aauto.com 888-844-3393
You may want to inspect the gears on the transfer case to see if they are okay. 1aauto.com 888-844-3393
You may want to check the vacuum lines to see if any of them need to be replaced. You can also see if there's power going to the actuator with a test light or an ohm meter. Hope this helps you out. 1aauto.com 888-844-3393
You may want to see that when you do put it in 4WD that the front shaft locks into place, and the transfer case is engaging it correctly. 1aauto.com 888-844-3393
The issue could be with one of the forks inside the transfer case not engaging all the way and what you are hearing is gear on gear contact. You will definitely want to bring it in and have it checked out before you use the 4x4 anymore.
I thought for sure it was my switch in the dash, so I replaced it, but no, the 4wd still didnt work. So it must be the actuator, I replaced that and still no 4wd. I checked the wiring, cleaned the grounds, checked fuses and searched forums and decided to bring it in to get diagnosed ao they could pinpoint the problem. Well they weren't able to pinpoint it and that cost $127.00 , lol. So i decided to replace the transfer case motor and used this video. It was very helpful. I didn't have to remove u joint bearing, the electrical connections were kinda hard to unhook. I had to manually put transfer case in nuetral to line up with new motor. I'm just a you tube mechanic so this was a bit challenging. I have no impact wrenches or means to raise vehicle, so it was tight under there. Anyway, I did it and it worked! I'm very happy. Thanks!
+cash money Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
Thanks for the video. My local professional wanted $500 for the motor, your site has it
for ~$163. They also wanted 3 hours in labor costs and your video is 15 minutes, but with fast forwarding of the movie, you might have had the truck on the lift for 45 minutes. Unfortunately it is hard to find an honest mechanic these days.
Great that you show diagnostics. That way you can tell if it is the switch or the motor, nice video Mike
wow what a job ahead I have coming up. Now I know why my truck wont go into 2hi and 2low Thanks Mike for the videos I am learning a lot.
Great job! I like the fast forwarding through monotonous parts, we can still see what you do but it shortens the video which is better than cutting away and skipping the section.
+supperterofsanity Thanks for watching. We're glad you liked it. 1aauto.com 866-403-3393
Good for you, Mike, to include a few words about diagnostics.
Christian Helser
I have a 1990 Chevy 2500 and I went to turn my 4x4 on which is on the ground and the light never turned on and it still is 2 wheels drive. Any advice I should look for or do to fix it?
You may want to check the fuse on that circuit to see if it's blown and needs to be replaced. If that's okay, you may want to test the power going to the switch, with a test light or an ohm meter.
If there's power going to the switch and none coming out of the switch when it is pressed, you may have a bad switch. Hope this helps you out. 1aauto.com 888-844-3393
Since you're dropping the front drive shaft, it'd be a good time to switch out the u-joints if they haven't been done before. I've done my rear about 3 or 4 times in my 04 silverado but never the front. Maybe on a rainy day. Thanks for the video. I may replace my motor this summer or just pick up a spare just in case.
It could be, you may want to test the power to the switch with a test light or an ohm meter.
Thank you for the informative video but I would certainly clean the driveshaft yoke with a solvent after dropping it on the dirty, rusted crossmember. I would also solvent clean the U-joint stub. Depending on the mileage of the vehicle I would tend to want to solvent clean all of the grease out of both U-joint caps and repack the bearings. Not too much work since it's all apart already. My truck was giving erratic 4HI to LO shifts for about a year and now it's stuck in low so I think it's time.
It could be either the switch, transfer case shift motor or the physical transfer case is broken. You might want to bring it to someone to have them diagnose the issue for you.
Great video, thanks, helped me out a lot. When I pulled the shift motor out and opened it up to replace the sensor it was full of oil. Is that supposed to be there. Thanks again
Excellent instructional with clear views of each step.
+Every-Day Joe Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/1A/TransferCaseShiftMotor/Chevy/Silverado1500/1AFWM00014?TH-cam&CTA+Comment&PPf2Yzhjmw
Try to put the truck in reverse and back down the road a little ways. Sometimes this will disengauge the system for you.
Very good you guys should sell dvd's on this kind of stuff
Stfu its free dont tell them that
love your videos, thanks.
I have a 1999 silverado 2500 and the 4wd buttons are not lighting up and its not going in 4wd. It say "service 4wd" in the display in dash. i replaced a blown fuse. checked other fuses and replaced the 4 button auto 4x4 controller on the dash.
Do you have a guess on what it is or what i should replace next? Transfer case shift motor? any help would be great. Its snowing in Colorado and 4x4 is handy and fun.
Thank you.
Thanks for the past response! Guess I should have noted that there was and still isn't a check engine. Thanks again.
All I need to know is how lng it takes!!!!
If you had a donor truck to take all of the parts from that would probably be the cheapest and easiest way to do this. It may be quite a bit of work though.
just got a 2004 GMC Yukon the driveshaft hooked on the transfer case shift motor , the 4 button selector switch does not light up at all
the works fine in 2WD still no light showing - i assume the problem is the TC shift motor wires have a issue
i need to check all the fuses and clean frame & body grounds 1st - i bought the 5.3 Yukon in this condition , it has a very nice body & interior
It might be an issue with the transfer case motor.
Hey Guys, so I live in Calgary Alberta......With this said, our winters get frigidly cold -20C common......my 4wd service comes on/fuse blows/lights on selector switch goes out. Nothing works...found a write up - not sure if its from GM directly. But it states, if your 20amp ATC fuse keeps blowing, but Encoder @ T-case works......front diff actuator works. You're getting get grounds.....good voltage at connectors....( Bench test front actuator ) and it works.......and there is no code for TCCM ( Transfer Case Control Module ) ....it is the 1640 connection - they used 18 gauge wire from factory but during colder than normal ambient temps - it will spike in amps and blow the fuse....The easy fix is replace with 25amp fuse. OR replace the Orange wire - with 16Awg. DONT GO SPLURGE ON PARTS BEFORE YOU DO ALL YOUR CHECKS!!!!
+Sunny Rooprai Thanks for the tip! We'll pass this info along to our production team.
You make it look so easy
my shift motor is bad so i just watched the video now im going to try wish me luck lol
I was stuck in 4HI when mine stopped working. Had to replace 4x4 shift motor (mates with transfer case), 4x4 module (signaled by clicking sound under glove compartment in passenger wall) , and then the lights just blinked and I had to replace the 4x4 actuator (under the battery)
.
moral of the story... don't wait to fix it.
Nicely Done , How is your price on the part? 80.00 Dollars free shipping?
Nevermind about the 4-Lo issue. I should read my manual! I need to be in neutral to engage. Never had a 4x4 before! Still have the turning issue.
00 Z71 with auto 4x4.Lights say it is in 4x4 .I jacked all tires off ground 4x4 works but I can grab tire and front no longer spin .back still turns.Why would it not have the power to turn front wheels?love your videos
+Jerry Bowen Some 4WD systems are designed to send more power to the wheel with traction. This might be what's happening. Thanks for watching. If any of our viewers needs to make this repair we carry the part shown in this video on our website. Here's a link to them www.1aauto.com/1A/TransferCaseShiftMotor/Chevy/Silverado1500/1AFWM00014?TH-cam&CTA%20Comment&ATony
Great video! I just got my 02 Silverado. When I turn very sharp, I hear a rubbing/grinding noise, and sometimes the truck bounces a little. I can hear my shift motor working seemingly normal when I shift into 4-Hi. When I drive in 4-Hi I it feels a bit rough and like there's a rubbing/grinding noise. I cannot shift into 4-Lo. Everything else about the truck seems great! My uncle, who lives in a different city and used to be a mechanic, thinks like the turning issue may be 4x4 related. Thoughts?
Direct linkage is the best. No computer bs
Hi there you showed how to test the motor while its attached to the truck, I have a 2001 olds bravada that doesn't have any 4wd switches, it is stuck in 4wd and I'm thinking it's the encoder motor. There isn't any way to test this one is there? I've been told there isn't any way to test it when it's not attached to the transfer case either or it will cause permanent damage to the motor.Fluid is perfect no blown fuses and no lights illuminated on the dash.
Thanks for the video was really nice, i was wondering is it possible to remove the wire harness and disconnect the motor without removing it? Or its better to remove it ?
+Sohaib Kholosy You will be able to disconnect everything just fine, but you will not have the clearance to physically remove the motor. Any viewers that are interested in purchasing the part in the video please follow the link! www.1aauto.com/1A/TransferCaseShiftMotor/Chevy/Silverado1500/1AFWM00014?TH-cam&CTA+Comment&PPf2Yzhjmw
I have a 2001 GMC Yukon XL and I'm having trouble figuring out if I need an actuator or replace transmission. I put it in gear and it will not move in reverse or forward. The first time it did it, I let it sit for a few hours and it moved about 35 feet then it wouldn't accelerate no more. When in gear it just idles and will not go. Please give me a plan of action.
Thanks for video. Need to order replacement. 2 questions: when bolting new motor in place, do the gears or motor need to be 'indexed' to match position of motor with position of transfer case? also, which part number for '05 tahoe with the 'auto' sensing 4wd? Thx again.
You shouldn't have to. As long as you follow this video you should be fine. We carry the replacement actuator shown in this video on our website. Here's a link to them goo.gl/RZDU2U
how much would one cost for a 96 chevy 1500 z71?
Great Videos. I have a problem similar to this. 05 Sierra 215k miles. My buttons have been working off and on for a few months. Today, when working and going at highway speed the transfew case shifted into neutral on its on and I lost all power to wheels. Pressed Auto 4WD, power returned and got home. Tried again later and same thing happened. Transfer case shift motor? 4WD Axle Actuator? Software issues? Thanks for your time
Thank you so much for the kind words regarding our videos. Given what you're describing I would lean more towards the transfer case shift motor needing to be replaced, however it's impossible to be certain of that without a proper diagnosis. Have the vehicle looked at to see if this is the part that needs to be replaced as the last thing you want to do is buy unnecessary parts and in turn perform unnecessary repairs to the vehicle if not needed. Thank you again, and have a great day!
Hi, Mike! I was wondering about your take on turning a 2x4 Ford F150 to a 4x4 as it's sort of relevant to this. It seems like it wouldn't be impossible...
I rebuild my 2005 Tahoe z71 transfer case np246 np8 because it had a pump knock problem and create a hole in the rear housing. Now my problem is that it won’t shift in any of the 4wd modes like in the video and the electronic encoder is making the same noise. I also was thinking that maybe that tab on the main output shaft under the clutch pack was installed incorrectly by the shift fork, but this seems exactly what my truck is doing. Could that tab be an issue for why the tc won’t engage in any other gear besides 2wd. The truck runs it’s just when I try to put in any 4wd it blinks and goes back to 2high.
Hi mike mine stack on 4Low how do I line mine up? And my button has 4 button instead of 3 button
I like good how too vids ,, keep them up
At 9:24 that noise that the driveshaft makes when your putting it back in is the same noise mine makes when I try to move the driveshaft without removing any bolts or anything yet. Is that normal? is that end of the driveshaft supposed to be able to move in the transfer case at all?
I have a 1990 chevy 2500 and I went to turn my 4x4 on which is on the ground and the light never turned on and it still is 2 wheels drive. Any advice I should look for or do to fix it?
This is a stupid question but when not in 4wd is it front or rear wd ? Thanks
I could use some help here! I have a 2001 Chevy s-10 four wheel drive, and I started hearing a loud banging noise coming from my front end when I'm driving in 4x4, I changed the actuator and it still makes the noise and sometimes I noticed that the 4 hi light will go out while I'm driving at 65 to 70 mph! Any help is appreciated!
I have an 04 yukon that occasionally while driving down the road it will go into neutral and will only in gauge into any gear if you switch to 4hi. Do you think it could be the switch or motor?
Hey my 99 chevy Silverado doesn't like to disengage the four wheel drive, when it does though it make a loud clunk and is as if hit a speed bump. Any ideas?
I took apart the gear shif stick did I put it together wron.
I have a 06 1500 hd .... On a recent hunting trip it would not stay locked in 2 wheel drive only for a mile then jump out and make a grinding noise. Much like gears toggling. Made it home in auto 4 wheel drive, and 4 h worked but locked up hard. Truck has 49000. Would that still point towards the drive motor? BTW...... Great videos!
If there happens to be a check engine light on, you may want to pull the code to see what it points to.
Thank you!
I have a 2001 Chevy Blazer. Is the "shift" motor the same as the "encoder" motor?
My 4HI does not engage. I already changed the actuator diaphragm and the cable. Still nothing. When I press the 4HI, it just blinks. I don't hear anything. What should I check next?
Thanks Kindly, Helped out !
Ever seen a 2002 2500HD Silverado have problems with the transfer case shifting into neutral by itself while driving down the road?
Hi thank for video it helps me a lot if I order parts from you how many days it takes to get it
+Sergio Ramirez Most orders reach their destination within 2-5 business days
How do I know if the problem is the motor or the control module? My 2005 Chevy Suburban will shift from 4 HI to Auto4WD and back, but will not go to 2WD or 4 LO. The button just flashes for several seconds after pushing, but it doesn't shift and stay lit up.
Help replaced throw out bearing clutch plate pressure and fly wheel everything is put back together however nothing happens when I try to shift the truck just rolls as though it's in nuetriral however the drive train doesnd not move Arou
Hello there went ahead and bought the part but I cannot get the teeth to line up... Any tips on how to go about that ?
How can I tell if mine is in 2wd mine locked the 4wd in 4l count get it out had to remove the motor and put manually I just want to make sure before I put the other one
great video thanks for sharing it with others
Thanks for watching. We're glad to hear that this has helped you out. If any of our viewers needs to make this repair we carry the replacement part shown in this video on our website goo.gl/aa15Or
I have a 2004 1500 Chevy z71 5.3 l V8, when I try to put my truck into 4x4 absolutely nothing happens. No matter what button I push, (4hi, 4lo, or auto) no lights blink it doesn't shift into 4x4. I don't hear any sounds like you have showed here in the video. It doesn't try to shift, it will not make any attmept. I have a service 4x4 light on. Can you shed any light on this for me please and thank you.
I just did this to my 04 Sierra 1500 and when I plugged in new encoder motor and switched it to 2wd on the button select after a minute my 4wd lights just went out and now I can’t get them to turn on any ideas? The switch turns on for a few seconds and then off
Hi mike mine stack on 4Low how do I line mine up? And my button has 4 button instead of 3 button. This is my second time I'm replacing mine the first time is true mechanic now it when out again why is that? This time I'm doing it my self and I'm going to video it and show it to you tube I need some in put from you I don't want to mess this thing up. Thanks for your video on you tube
Hi Mike I don't hear anything could it be the switch? Thanks
I have pretty much the same truck, with a slight different problem. Everytime I click the buttons to swap to 4low or any other mode, nothing happens at all. No lights blink. No sounds are made. Any ideas whats wrong?
my 2005 tahoe makes a loud clang clang sound, it goes into 4 HI and AUTO 4WD fine, only makes this sound when i try to go to 4 LO and will not go into 4 LO, any ideas?????
@ Logan Stone
love your videos, thanks.
I have a 1999 silverado 2500 and the 4wd buttons are not lighting up and its not going in 4wd. It say "service 4wd" in the display in dash. i replaced a blown fuse. checked other fuses and replaced the 4 button auto 4x4 controller on the dash.
Do you have a guess on what it is or what i should replace next? Transfer case shift motor? any help would be great. Its snowing in Colorado and 4x4 is handy and fun.
Thank you.
You may want to pull the code from the computer. This should help to point you in the right direction as to what might be causing the problem. Hope this helps you out. 1aauto.com 888-844-3393
i have a 2003 chevy 2500hd and my actuator is good and it down shifts the gear ratio when put in 4lo and 4hi but i don't have power to the front wheels what could cause this.
I have a 98 chevy Z71. It has the push button selector, when i go to engage or disengage it will make a racket like it's hitting hard. Yes it goes into all selections. Also, what gear should the trans be in when switching in and out of 4X4? Can u give me a clue where to start to resolve this. Thanks!!!
It may be shift on the fly, meaning you may need to be moving at least 10 miles an hour for the 4WD to engage. You may want to also check the owners manual, as it should indicate the proper shifting procedure. Hope this helps you out. 1aauto.com 888-844-3393
Thanks!
My 2005 Silverado hasn't been able to go into 4wd low for a few months now. Today while driving in 2wd every time I went down a long hill where it was essentially coasting the transfer case was totally disengaging as if my transmission was in neutral. Stopping and cycling from 4wd back to 2wd fixed it each time with a super loud clunk. Is the encoder motor the likely culprit for both the new prob plus the old one of no 4wd low?
+wmkess Thank you for checking us out. This certainly could be the reason for your issue. 1aauto.com
Was this part the fix for your problem? My 2004 is doing the exact thing as you described in your comment.
I can't get the splines to line up between the new shift motor and the transfer case. It doesn't seem possible to turn either one of them.
I bought a truck they said the previous owner pulled the 4x4 out does that mean they prolly pulles the whole transfer case out
What if the transfer case will go into 4wd high no problem but fail to engage 4wd low? My 2005 Silverado 1500 does this now. I can hear a loud clunk, like it typically made in the past when it engages into low, but it doesn't engage and then it clunks again like it is giving it a second shot. It has been doing this even after multiple restarts and trying it at a stand still and a slow roll (1-3 mph like the manual states) and always in neutral.
wmkess when putting it in 4wd low make sure it's a nuetral and your stopped. 4wd high is a shift on the fly but low is different...
question I have a 96 silverado K1500 with the shiftier on the floor. when i try to put it into 4x4 it grinds and little and the drops into 4WL but its not really in 4WL the motor acts like it is but the front axle is not truly engaged. any ideas on what it could be?
HI Mark, You may want to take a look at the axle 4WD actuator to see if it's acting up. We carry new ones on our website. Here's a link to them if you would like to see what we carry. Hope this helps you out. www.1aauto.com/1A/four-wheel-drive-parts/Chevy/K1500-Truck/-/-/1996?VideoReply&TH-cam&ATony
hi, i have a 2006 chevrolet suburban 1500 and my problem is this, 4x4 switch lights turn on and then off, just the red light on neutral is on, and nothing works not even a sound, i have the switch changed and the 4x4 shift motor also, as you did on the video, first when i started the truck worked fine for the first five minutes and then it stopped working again, do you have any recomendation? please thanks for your time,
You may want to inspect the wiring going to the shift motor just to make sure that there's not a frayed wire or something which may be causing this to happen. Hope this helps you out. 1aauto.com 888-844-3393
i have an 05 silverado and having trouble with my 4wd. service 4wd comes up on cluster and stays there, no lights on the switch because the fuse blows. Thinking its the transfer case motor but not sure. Was having trouble earlier trying to get her in 4wd but after some time she would eventuallly go in, but now no dice. Think the motor is my probem? how much does one usually go for, theres a napa here in town that might have them, thanks.
We carry this part shown in the video on our website, here's a link to them www.1aauto.com/2001-02-transfer-case-shift-motor/i/1afwm00014?TH-cam&YoueTube&ATony You should pull the code to see what it's pointing to. Hope this helps you out. 1aauto.com 866-403-3393
i have a 1994 chevy 1500 i have it in 2 high but it wont let me drive it will only go in reverse and 2 and 1 gear but when im go out of 2 gear and kick it into drive it will let me drive but when i stop i have to put it back into 2 gear to go again
i need help on finding out what i need to fix it
So I replaced this and my truck still doesn’t recognize neutral, so I can’t get back to 2hi or 4 auto. Any suggestions?
+DragonNF We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
Good vid but you should mention eye protection. Every time I work under a car I get rust,dirt,fluid,etc etc in my eye and swear Ill never do it again lol
+Donald Steiner Eye protection should always be used no mater what job you are performing! Any other viewers interested in purchasing these parts please visit this link:
www.1aauto.com/1A/TransferCaseShiftMotor/Chevy/Silverado1500/1AFWM00014?TH-cam&PPf2Yzhjmw&%
I have a question. I have an 04 Silverado 1500. It's telling me to service 4WD and my ABS light is on along with my Parking brake light(even tho the brake is not on). Would that be the issue fixed in this video or is it something more? It won't go into 4WD either.
+haroaero You may want to try to see if there is a code stored in the computer. If there is it should help to point you in a direction. 1aauto.com
i just put new motor on my tahoe it still wont make a sound or shift lights work shows its in "N" yet no noise at all HELP!!
I just replaced the 4x4 actuator on mine and the front wheels still won't spin and it won't go into 4x4 low or netural
I recently had my transmission rebuilt on my 2001 S10 4×4, now my 4×4 does not work, I changed the motor switch thinking it was the issue, I can hear it changing but will not engage the trnsfer case, I added 1 addition quart of transmission fluid just to be on the safe side that it may need more, do I need to add more fluid. What could be the issue, the tensfer case is not damged..
You may want to check the dipstick on the transmission to make sure that it's not over filled. That system also runs off of vacuum, check all of the vacuum lines in the engine compartment to see if any of them are broke, or if there's a vacuum leak. There's an actuator that that tends to fail on that truck too. Here's a video that will show you what to look for. Hope this helps you out. How To Install Replace 4WD Front Axle Vacuum Actuator GMC S15 Sonoma Chevy Blazer 1AAuto.com
Thank u..I will check out dis wk...
My 2009 Silverado just went out recently. Manual shift to 4H, 4L, but nothing happens. The 4-wheel light doesn't come on either. I just used 4H 2 weeks ago. When shifting to 4H, I don't hear any noises..I'm leading toward the actuator but know nothing about vehicle maintenance. Any help in the right direction would be greatly appreciated.
+Lyman Tsinnie You may want to test the power going to the actuator to see if there's power going to it when the switch is activated
I have a Blazer LT 99 and i just changed the transfer case shift motor, but now my switches buttons wont light up?
i checked all the fuses and i did replace the switch it self, any ideas?
You may want to test the power going to the switch with a test light or an ohm meter, to see if there's power to the switch. Hope this helps you out. 1aauto.com 866-403-3393
I have a 2001 silverado and my 4wd only engages into the low 4wd, it goes into high and auto but it doesn't work on does modes it only works on the low mode. Do you think is the transfer case shift motor? @1Aautoparts
It's possible that it's the shift motor. Are you getting a 4WD light or anything similar on the dash? 1aauto.com?TH-cam&CTA%20Comment&ATony 866-403-3393
1A Auto Parts no nothing, it just doesn't engage into 4wd high or automatic mode. Just the low mode. But thanks amazing page. And you guys sell quality products keep it up.
I have a 2005 Chevy Colorado and can hear my transfer case shift motor whine when it tries to shift. I do get a "4WD Serv" error on the dashboard. I cannot find the term "Transfer Case Shift Motor" on your site for my vehicle. The front shift actuator does come up but I don't think that's what I need. Do you have one?
+fastrivers We currently do not carry one for the transfer case for this particular vehicle. Thanks for asking. 1aauto.com
frontt end whines all the time on my 04 yukon i changed the fluid and found no metal flakes but its sttill loud had it inspected no play found in the hub assemblies what is it
Thank you for watching! Unfortunately it could be one of many things. I would double check all of the front end including ball joints and the tie rods. Its possible the noise is also coming from inside the case. Hope this helps!
1aauto.com 888-844-3393
Great video!!!
So I'm having same problem with my 04 Silverado except mine goes into 4 lo and not 4 hi ,it blinks like this video and goes back to 2wd . I do have new transfer case motor here to be installed . Will this fix problem ?
Also I do get a service 4wd light
lonnie ruybal mine does the same thing only it goes into 4 hi but not lo. but it won't work. I can hear the actuator hum and then the light will indicate it's in 4 hi but only the 2 back wheels spin still. let me know if you find anything. 99 silverado
Is there any fluid that has to be drained first before I do this on a 98 Silverado z71
+Vanison Zore Nope, not on this repair. Good luck and let us know how it goes! For anyone else who might be doing this job, we carry the parts shown in the video on our website. Order from us and we'll cover the shipping. Here's a link: www.1aauto.com/1A/TransferCaseShiftMotor/Chevy/Silverado1500/1AFWM00014?TH-cam&CTA%20Comment&ATony
Thanks I fixed it
+Vanison Zore That's awesome! Congratulations on the successful repair. We're glad the video helped you out. 1aauto.com 866-403-3393
Awesome vid
the nub that sticks out of the transfer case doesnt want to line up with the female part on the shift motor for my 01 silverado, how do i line it up? Also if i just plug in the new shift motor without installing it to the transfer case, will the motor spin when I press the 4x4 buttons? I bought a new shift motor and pluged it in, didnt bolt it up, and the motor is just buzzing and not turning. its brand new...defective unit?
+glamisfanatic You will want to plug the encoder motor in first and set it to what the transfer case is set to. So if the vehicle is in 2WD then you need to set it to 2WD first. 1aauto.com
hi my name is lisa, I just bought a 2000 s-10 chevy blazer, it is a 4x4 4wd also, the problem that I have it, I never had an 4x4 vechicle/suv. all the lights were flashing and if I get it over 30mph it will run right, under 20 mph it will hesitate and I have to force it to make go over 30. I had a lot of different answers saying it was the transmission, computer brain, and now the catalac converter could be stopped up. I don't know what the real problem is, can you please help me to find a better solution to this problem. Thanks Lisa
2000 S-10 CHEVY BLAZER, 4 DR, 4WD, 6 CYCLEDER
There may be a vacuum leak in the 4WD system. If there's a check engine light on. you may want to have the code pulled, it may help to tell you what the issue is. 1aauto.com 888-844-3393
I'm having problems with mine shifting into four-wheel drive low could this be the problem
It's possible, we recommend that you take your vehicle to a local, reputable mechanic for an accurate diagnosis. +B I
It a rebuilt transfer case with about a thousand miles on it