I have to say I was skeptical as to whether this fix would work. I had the necessary tools from when I fixed a stick drift issue and so decided to give it a go on the RB button which wasn’t registering lighter taps, where LB would work with the same force. In my case, the plastic that contacts the button didn’t appear worn at all. I used a small piece of adhesive address label just to decrease the gap between plastic and button slightly and it has worked perfectly as a fix so far. The button still even has that satisfying click feel when pressed. Thanks for sharing this solution!
Can I do the same process but instead of decreasing the gap between the plastic and the button, you are increasing the gap between the plastic and the button?
@@BobRoss-wm3lc it did work for quite a while but I don’t use that controller anymore. It developed an issue with stick drift and I discarded it entirely. A few times I had to open it up again and reapply some sticky label or whatever for the RB button issue. To be honest, it’s only ever going to be a temporary solution.
@@bonk4225 No they're not it's a grab for money 😭😭 they literally designed their own screws that don't have common screwdrivers so you can't DIY fix your controller. you deadass have to order a special screwdriver from Microsoft at extra cost if you even want a chance at fixing broken controllers. And my controllers go bad every 2-3 months. Different things every time. Controller drift is something most people live with, buttons stick/break/stop working, headphone jack just straight up breaks, etc. I have like 4 different unusable (for gaming) controllers because I can't fix them DIY. If they're so short term they shouldn't be like 60-90 dollars 💀💀
@@bonk4225 They are bad. Bumpers go bad all the time. I have 3 with messed up USB ports. One the b button stopped working. The d-pad uses a plastic bubbled sticker for spring action and electrical contact and that starts making noise and has poor activation. I don't know why everyone doesn't use SEGA Saturn D-pad, the patent expired years ago.
Same WTF😂🤯🤯 ive been avoiding playing with this controller just because of the bumper and now it works perfectly fine im pissed because i bought it back in October because the one i had was badly wrecked from raging and now it finally works lmao
I've got this issue right now and I've performed some pretty serious surgeries on my controllers in the past, so I'm not shy about opening the housing, but I should say that this problem can properly be fixed with electrical contact cleaner. The switch is only registering intermittently, and most often with deep presses, it's because there's dirt in the switch interrupting the connection. Get compressed electrical contact cleaner, or standard isopropyl alcohol should work in a pinch, and spray directly into the switch. Rapidly press the switch repeatedly for a minute or so. Allow to dry. No mod necessary.
@@TafaraMolife I believe it's mostly isopropyl alcohol, or at least smells indistinguishable from it, but it comes in a pressurized can that can spray it into hard to reach places, like into the thumbstick switch mechanism found inside controllers. And this should work in practically every instance of joystick drift as long as no physical damage had been done to the switch mechanism, patient care of your controllers and you're getting drift then this will almost always take care of it. You can try like dripping isopropyl alcohol into the mechanism you might have to do it repeatedly a few times actually get it in there and working and allow it more time to dry. If you go that route you'll want to use the highest purity you can find, the lower the purity the more water there will be in the water will linger much longer than the alcohol inside the switch which could cause electrical shorts which could damage the circuit board
Glad I found this so quickly in the comments. Just dumped some alchohol-ish cleaning solution over the switch a few times, blew inside it and did the rapid tapping. Fixed it. Thanks
Another tip that can help. Sometimes the switch the plastic presses on can sack down a little. Fold a strip of cardboard and use a size that barely fits in the gap so the cardboard pushes up the switch closer to the plastic that is supposed to press it.
definitely putting this in a playlist for later, right now the blowing method works, but f that stops then i’ll for sure use this method, as my controller is a bundle exclusive and i want to do everything to protect it
Thank you so much! I just had to put 5-7 layers of thin tape on it, and it started working. It was my right bumper. The switch initially only registered when it was pressed on its sweet spot, but after I added the tape it works in every single part of the bumper!
My issue was a little different so I'll leave it here: I was having a similar issue and upon opening it up I discovered that little spike that registers the bumper press was broken, so it would bend instead of registering a press. I removed it, and super glued it back on to fix my issue! Thanks for the guide on opening up the controller!
Mate I just blew into the controller and now it all of a sudden just works? I thought this was the stuff of legend where in elementary school Timmy repaired his 90’s game cartridges with a straw! I’ve entered a new level of evolution, my marksmanship of repair is outstanding! Oh and nice video, you earned a like.
You rock! This video needs more views! Your trick worked for me!!! I used painters tape instead of electrical tape though, easier to work with. Thanks so much!
I’ve been having problems with my lb button too and when you talked about the blowing method I was like I’m not taking apart my controller so I got nothing to lose and I did the blowing method and it freaking worked!!! Thx browski!!!
a big tip, If blowing doesnt work, try a can of compressed air, i was blowing, i was putting rubbing alcohol, everything, I was about to take it apart but decided to try canned air and it worked perfectly
Thanks for the video! It's nice to finally find a guide that suggests an actually permanent and cheap solution in comparison to the 10,000 "blow under the bumper bro, instant fix" videos
This control is quite expensive and they dare make it so defective. The number of views here demonstrate this is a common issue. Thank you for the instructions.
Bro... You legit saved me from a crisis of returning my Xbox controller, to get a refund. So I bought this used Xbox one controller, just like yours except black. And the art button would only work when pressed really really hard, and after seeing your method and your way of putting that sticker. I did the exact same thing, and all I have to say is, you saved me a lot of trouble. Why? Controllers nowadays are super duper expensive, 50 to $60 for a controller, or for an Xbox elite controller would lead up to $100 or more. I bought this controller for $20, luckily it came in its original box, with the cable, and the back cover. Overall man, after seeing this video, you saved me man, you saved me. Thank you man, I'm glad I came across this video before actually returning it. I was able to successfully open the controller to do exactly just that, and was able to test it out later on. Everything now works perfectly.
This is a possible solution to the problem however the issue (in this video) is actually a dirty switch. You prove it by showing that one of the switched only seem to work with deep pressing it even without the plastic part. If you spray some contact cleaner (or Isopropyl Alcohol) to the top of that switch and press it a bunch of times (to help it get inside the switch) then the issue could be fixed without the tape. I have just fixed mine yesterday :) Thanks for the video, it helped alot on how to diagnose the problem!
i did the solution from this video and it only worked for about 30 minutes but after trying your solution it seems to work completely and without any tape
@@aRandomDuck. the goal is to get the contact cleaner inside the microswitch. If you spray it from the side which pushes in, the contact cleaner will eventually make it inside the switch if you keep pressing it.
Brilliant! I've got a set of security screwdrivers showing up tomorrow, but I love your makeshift approach, especially with the tape. Very resourceful. &, the way you showcased everything was clear too PS: I needed to replace the pin of my Series X controller, the 1 that pushed LB's button/sensor... it was skinnier than the controller's 1 in this vid, & was fully snapped off, + wouldn't even superglue well. So, I cut a piece of slim plastic (from a yogurt container), wrapped it in electrician's tape, then filled the slot, & it's works great. Can't tell there's been a repair 🙏🏼
First comment I have ever made on a video, bought a second hand controller online and was gutted when my RB didn't work, your blowing trick worked first time! Thank you so much!
I got my 1st xbox one controller along with the console a few years ago when i was young ish when all of a sudden the RB button wasn't working and ive had it since but never used it and when u said to blow on it all of a sudden it was like brand new holy cow thank you for making this godly video truely u are a legend
LOL, the blowing into the space between RB and RT actually worked, i did not know you could do this and i laughed pretty hard when it worked and i am glad i know now, thank you my guy.
Thank you! I've gone through 3 Xbox controllers in the last 6 months because I use the right bumper to shoot in FPS games instead of the right trigger, and the right bumper doesn't last more than a couple months. This seems to have fixed the issue for now! Hopefully Microsoft can make a higher quality controller next time around...
Thank you!!! I got the tool set. It was 10 bucks. I have cracked open five 'dead' controllers and brought them all back to life except for one! One was your tape fix, two needed crazy glue for broken bumper posts that had cracked off, and one just needed a good cleaning, parts were sticking. The tool set is great!! And as a bonus, as I sat at a table with eviscerated controllers to and fro, my kid gave me my Christmas present. Two Overwatch thumbstick caps. Great timing. Thanks again and Happy New Year!!
Thank YOU DUDE. The Tape took a few attempts before actually getting used to, but with the right positioning, the tape method works about 98% of the time!
lmfao, I just realized that I fixed my controller already years ago the exact same way. I had in my mind "wait, didn't you already fix this problem in the past?" but I wasn't sure. Now my bumper on new controller is not working again and I searched for a solution. And bam there it is, you bring me my memory back 😂 Thanks a lot! Edit: And yes, the fix worked for years and even longer than the controller itself. On my old controller the fix is still working but the controller itself had to be replaced after such a long time of usage.
Thank you for saving me having to buy another controller. I broke one of the clips on the top-back of the left grip but that was my fault and a common occurance with anything clip based. Can barely tell its broken but I'd rather have that minor issue then have to buy a whole new controller. Thanks again, loved the screwdriver lmao
Thank you soooo much. This worked for me. The only thing i did differently was i added more layers of tape. You added 2 but i added 5 because my tape was really thin. Thank you again. You just saved me from buying another controller
This video will give thousands of people the confidence to do this. Well done, Sir. Like Geralt of Rivia, you are a true friend of Hugh Manatee (whoever that is)
Here's a small tip: If you don't want to permanently break a flat head screw driver, use a 5/64 bit. It works like a charm if you wedge it in there properly. EDIT: You can also break off that stupid little center post and use a regular torx bit.
A very informative video in a short format! Thanks to you I was able to repair my controller (it is a custom one so it really means something to me) keep it up!
the little lb poker on the plastic bit you detach somehow separated from everything.. This guide plus a bit of super glue fixed everything. You are the best!
What's crazy is the first fix he said that didn't work for him (Blowing into the controller with the trigger pushed down) worked for me first try! Couldn't be happier with this vid!
Thanks man! You are AMAZING! I play FIFA too so the defender switching was a nightmare! The only downside it that the clicking sound is considerably muted, but that's fine for me.
I really wish xbox would just come up with a good controller we shouldn't have to be fixing our own controllers just to have them in a workable state however thank you for the fix you are brilliant
Oh man! I'v got a new controller recently and even didn't think that it would be so unexpected problem. I guess after nier automata this broke due to pressing too much hard this button. I couldn't imagine that I can break this controller that way. So thank you for solving this problem. Now I know what to do.
The lever on my RB that depresses the button was broken, so each press didn’t actually press the button. Some super glue on the cracked arm and an added piece of tape like you said to the end that presses the button and it now works better and smoother than before. Many thanks, many many thanks!! Side note: my LB, RB and Xbox button cover were attached slightly different. They come off independent of one another. Same method if you come across this, always use EXTREME CARE when handling this level of plastic, breaks easy. Good luck!!
This worked, thanks. 2 strips of electrical tape exactly. I already owned a security torx screwdriver from when I changed my analog sticks to metal ones 😁.
imma be 100% honest here, ive been having issues with destiny not registering my melee but this helped completely, this will forever be saved to my playlist, rock on
I opened up mine and found that the piece that you put tape over had completely broken, all I did was open up my old controller that had working bumpers and switched them and I was ready to go
Soooo how are you supposed to take out the battery pack of the xbox elite s2 😂😂 I'm on my 2nd one the 1st one had a bad lb now my rb on my 2nd one is broken and I never slam my controller or nothing
THANK U SOOOO MUCH! It works for my controller, I was so scared to repair it cause it's an special edition from Gear of War but I saw your vid & did it, thank u again, you're awesome!
I had the opposite problem. The switch was registering as always being pressed. It appears to have been that black plastic bar right above the switch holding it in. Wedging a thin plastic tool very VERY gently between the bar and the body of the switch seemed to relieve the pressure on the button. This video however still gave me a good look at how to open the controller and get at the shoulder buttons. Good vid.
I have the same issue, my LB button triggers on release or when I touch it VERY gently. It's impossible to play games with. I hoped there would be a software fix that could configure the sensitivity ...
This helped alot! The little prong that you extended in the video? It was broken on my controller! I've used two part glue to repair it so hopefully that'll give it an extension on its life! Thanks for taking the time to make this video!
Hey guys! So this actually works. And no I’m not a robot or a fake account but this seriously works. I fixed mine today by firstly purchasing a T8 Screwdriver to get the screws out, then bought some black thick tape idk the name but it’s the black one that thick one and erm I put three layers on the thing this guy put the tape on and then put the controller back together and it works like a charm! I’ll make a video later on. Anyways THIS WORKS!
Thank you EVER so much. I have bought controllers 1 or 2 times a year because of this and now I have 6 that I can repair and should never have to buy another.....except when I get the Series X....if ever. Thanks again!!!
Thank you SO much! I JUST used this video to fix my RB on my controller. I had to take apart other, older controllers to use their bumper strip. Tip for other people! if the USB inputs are different, (micro vs USB-c) then the connectors/inserts are different! You'll need to match USB inputs if you are taking parts from other controllers. Active reload here I come! :D
this is literally the most helpful and basic videos I have ever seen on youtube thank you so much!
This was way better than any of the "high value" videos. Simple, good angles and lighting, and a much cheaper fix than a replacement bumper.
good angles=?? did we watch same video???
@@tpkkr clearly you watched something else if you disagree
I have to say I was skeptical as to whether this fix would work. I had the necessary tools from when I fixed a stick drift issue and so decided to give it a go on the RB button which wasn’t registering lighter taps, where LB would work with the same force. In my case, the plastic that contacts the button didn’t appear worn at all. I used a small piece of adhesive address label just to decrease the gap between plastic and button slightly and it has worked perfectly as a fix so far. The button still even has that satisfying click feel when pressed. Thanks for sharing this solution!
Can I do the same process but instead of decreasing the gap between the plastic and the button, you are increasing the gap between the plastic and the button?
Still working for you?
@@BobRoss-wm3lc it did work for quite a while but I don’t use that controller anymore. It developed an issue with stick drift and I discarded it entirely. A few times I had to open it up again and reapply some sticky label or whatever for the RB button issue. To be honest, it’s only ever going to be a temporary solution.
This works wonderfully even with a regular tape, saved me from the cost of repair or even the cost of getting a new controller. Thanks homie!
The one thing i hate is that when one button dosent work and the others do it feels like you just wasted all the good buttons.
smh
Dude screw this. Shouldnt have to worry about the controller. But its xbox
@@bonk4225 No they're not it's a grab for money 😭😭 they literally designed their own screws that don't have common screwdrivers so you can't DIY fix your controller. you deadass have to order a special screwdriver from Microsoft at extra cost if you even want a chance at fixing broken controllers.
And my controllers go bad every 2-3 months. Different things every time. Controller drift is something most people live with, buttons stick/break/stop working, headphone jack just straight up breaks, etc.
I have like 4 different unusable (for gaming) controllers because I can't fix them DIY. If they're so short term they shouldn't be like 60-90 dollars 💀💀
@@bonk4225 Quite frustrating lol
@@bonk4225 They are bad. Bumpers go bad all the time. I have 3 with messed up USB ports. One the b button stopped working. The d-pad uses a plastic bubbled sticker for spring action and electrical contact and that starts making noise and has poor activation. I don't know why everyone doesn't use SEGA Saturn D-pad, the patent expired years ago.
This method worked wonderfully. Even though the process of controller deconstruction was different for me, I still have to thank you for this guide.
When you mentioned the blowing part, i tried and it just works perfectly fine tnx for the video lol
Same
Same WTF😂🤯🤯 ive been avoiding playing with this controller just because of the bumper and now it works perfectly fine im pissed because i bought it back in October because the one i had was badly wrecked from raging and now it finally works lmao
Same
Same
@@nathannoble4537 how did it works ? Did you repair it or it just happens to suddenly working again for no reason ?
I've got this issue right now and I've performed some pretty serious surgeries on my controllers in the past, so I'm not shy about opening the housing, but I should say that this problem can properly be fixed with electrical contact cleaner. The switch is only registering intermittently, and most often with deep presses, it's because there's dirt in the switch interrupting the connection. Get compressed electrical contact cleaner, or standard isopropyl alcohol should work in a pinch, and spray directly into the switch. Rapidly press the switch repeatedly for a minute or so. Allow to dry. No mod necessary.
Can I use methylated spirit
?
@@TafaraMolife I believe it's mostly isopropyl alcohol, or at least smells indistinguishable from it, but it comes in a pressurized can that can spray it into hard to reach places, like into the thumbstick switch mechanism found inside controllers. And this should work in practically every instance of joystick drift as long as no physical damage had been done to the switch mechanism, patient care of your controllers and you're getting drift then this will almost always take care of it. You can try like dripping isopropyl alcohol into the mechanism you might have to do it repeatedly a few times actually get it in there and working and allow it more time to dry. If you go that route you'll want to use the highest purity you can find, the lower the purity the more water there will be in the water will linger much longer than the alcohol inside the switch which could cause electrical shorts which could damage the circuit board
Glad I found this so quickly in the comments. Just dumped some alchohol-ish cleaning solution over the switch a few times, blew inside it and did the rapid tapping. Fixed it. Thanks
yes, this i was looking for. something wrong with the switch. the thing is so hard to replace not as easy as ps4 switches
How do I use the alcohol without damaging the controller?
i should’ve watched this video before smashing my controller on my desk..
Lol
Lol
Lol
same
Lol
Another tip that can help. Sometimes the switch the plastic presses on can sack down a little. Fold a strip of cardboard and use a size that barely fits in the gap so the cardboard pushes up the switch closer to the plastic that is supposed to press it.
definitely putting this in a playlist for later, right now the blowing method works, but f that stops then i’ll for sure use this method, as my controller is a bundle exclusive and i want to do everything to protect it
Thank you so much! I just had to put 5-7 layers of thin tape on it, and it started working. It was my right bumper. The switch initially only registered when it was pressed on its sweet spot, but after I added the tape it works in every single part of the bumper!
My issue was a little different so I'll leave it here: I was having a similar issue and upon opening it up I discovered that little spike that registers the bumper press was broken, so it would bend instead of registering a press. I removed it, and super glued it back on to fix my issue! Thanks for the guide on opening up the controller!
Same
Same
Mine was snapped on 1 side and can’t find the snapped part now🤣..
Mate I just blew into the controller and now it all of a sudden just works? I thought this was the stuff of legend where in elementary school Timmy repaired his 90’s game cartridges with a straw! I’ve entered a new level of evolution, my marksmanship of repair is outstanding!
Oh and nice video, you earned a like.
You rock! This video needs more views! Your trick worked for me!!!
I used painters tape instead of electrical tape though, easier to work with.
Thanks so much!
Gald it worked for you!
Amphax A h is very gald for you!
Wtf I actually just blue is like hard and now it working like new 🤣
JustAYoungPR0 oh shit must have been in a hurry when typing my bad 🤣🤷🏻♂️
JustAYoungPR0 r/justtofunnyforearthandsincethisisalreadyareallylongsubredditwhynotmakeitlongerbysayingallthisrandomcrap
I’ve been having problems with my lb button too and when you talked about the blowing method I was like I’m not taking apart my controller so I got nothing to lose and I did the blowing method and it freaking worked!!! Thx browski!!!
a big tip, If blowing doesnt work, try a can of compressed air, i was blowing, i was putting rubbing alcohol, everything, I was about to take it apart but decided to try canned air and it worked perfectly
I tried compressed air and it didn't make a difference and then it just eventually got worse
@Myxtiqz He means computer duster, the compressed air with the thin plastic straw that you use to blow dust out of electronics like keyboards
@Plat II no WD-40 is a liquid
Canned air? Like that air in a bottle thing from the lorax movie?
My dude! A lifesaver. It took a few attempts to get the tape in the perfect spot lol, but fixed the issue of a dodgy softpress.
Thanks for the video! It's nice to finally find a guide that suggests an actually permanent and cheap solution in comparison to the 10,000 "blow under the bumper bro, instant fix" videos
This control is quite expensive and they dare make it so defective. The number of views here demonstrate this is a common issue.
Thank you for the instructions.
Clear, concise, straight to the point. Worked like a charm. Also the security bit is a Torx, size TR9.
Where can I get one?
It’s TR8
@@MusicMan4u any tool shop. It is TR8 not TR9
@@narutothethebigdaddy3378 good to know thanks. Game stop doesn't want anyone to know this
@@MusicMan4u its actually the t9h I have it
Bro... You legit saved me from a crisis of returning my Xbox controller, to get a refund. So I bought this used Xbox one controller, just like yours except black. And the art button would only work when pressed really really hard, and after seeing your method and your way of putting that sticker. I did the exact same thing, and all I have to say is, you saved me a lot of trouble. Why? Controllers nowadays are super duper expensive, 50 to $60 for a controller, or for an Xbox elite controller would lead up to $100 or more. I bought this controller for $20, luckily it came in its original box, with the cable, and the back cover. Overall man, after seeing this video, you saved me man, you saved me. Thank you man, I'm glad I came across this video before actually returning it. I was able to successfully open the controller to do exactly just that, and was able to test it out later on. Everything now works perfectly.
I didn’t even know blowing into the bumpers was a method so I tried it and now it works! Thank you
I did the same now it's broken again
@@davematulessy1208lmao
NO WAY, the "blowing method" actually worked... i'd never heard anyone else talk about it before. thanks so much!
This is a possible solution to the problem however the issue (in this video) is actually a dirty switch. You prove it by showing that one of the switched only seem to work with deep pressing it even without the plastic part. If you spray some contact cleaner (or Isopropyl Alcohol) to the top of that switch and press it a bunch of times (to help it get inside the switch) then the issue could be fixed without the tape. I have just fixed mine yesterday :) Thanks for the video, it helped alot on how to diagnose the problem!
BROOOO THANKS SO MUCH
i did the solution from this video and it only worked for about 30 minutes but after trying your solution it seems to work completely and without any tape
Top of the switch, in what way?
@@aRandomDuck. the goal is to get the contact cleaner inside the microswitch. If you spray it from the side which pushes in, the contact cleaner will eventually make it inside the switch if you keep pressing it.
@@Norrecito is it OK if I pull down lt and put it in through that gap?
Brilliant! I've got a set of security screwdrivers showing up tomorrow, but I love your makeshift approach, especially with the tape. Very resourceful. &, the way you showcased everything was clear too PS: I needed to replace the pin of my Series X controller, the 1 that pushed LB's button/sensor... it was skinnier than the controller's 1 in this vid, & was fully snapped off, + wouldn't even superglue well. So, I cut a piece of slim plastic (from a yogurt container), wrapped it in electrician's tape, then filled the slot, & it's works great. Can't tell there's been a repair 🙏🏼
Wow what an easy fix, blew into my RB button and it started working. Feel so stupid for not thinking of that LOL. Thanks!
First comment I have ever made on a video, bought a second hand controller online and was gutted when my RB didn't work, your blowing trick worked first time!
Thank you so much!
I got my 1st xbox one controller along with the console a few years ago when i was young ish when all of a sudden the RB button wasn't working and ive had it since but never used it and when u said to blow on it all of a sudden it was like brand new holy cow thank you for making this godly video truely u are a legend
LOL, the blowing into the space between RB and RT actually worked, i did not know you could do this and i laughed pretty hard when it worked and i am glad i know now, thank you my guy.
It worked, and i even made a custom clntroller out of it. And thank you sooooo mutch, legend
Edit: it stopped working
How did you do a custom?
The black Plague he broke it
You misssd the joke
@@Xaenok it wasnt broken
ScaryMøst you find a solution at least 😂
Mr Beast thought he like replaced some parts with his own to design it to his likings
2 years later and this is still applicale thank you so much bro
Thank you! I've gone through 3 Xbox controllers in the last 6 months because I use the right bumper to shoot in FPS games instead of the right trigger, and the right bumper doesn't last more than a couple months. This seems to have fixed the issue for now! Hopefully Microsoft can make a higher quality controller next time around...
I know the feeling it pisses me off! My 360 controllers bumpers still work to this day but Xbox one, NOOOOOOOOO
Thank you!!!
I got the tool set. It was 10 bucks. I have cracked open five 'dead' controllers and brought them all back to life except for one! One was your tape fix, two needed crazy glue for broken bumper posts that had cracked off, and one just needed a good cleaning, parts were sticking.
The tool set is great!! And as a bonus, as I sat at a table with eviscerated controllers to and fro, my kid gave me my Christmas present.
Two Overwatch thumbstick caps. Great timing.
Thanks again and Happy New Year!!
God bless you, my dude. The thing that bugs me is why Microsoft decided to go with such a cheap materials for the bumpers, its unacceptable.
Yeah man but the controllers are cheap just get an elite for high quality pay more you get more.
Theres a controller with rgb Lights with high quality bumpers called spectra
It's truly a joke. I have probably had fifteen different controllers. I will just fix them from now on.
Bought a button kit with an included t8 security screwdriver from Amazon and fixed my Xbox controller thanks to this video. Amazing. Thanks so much.
Protect this man at all costs
Thank YOU DUDE. The Tape took a few attempts before actually getting used to, but with the right positioning, the tape method works about 98% of the time!
3 layers later and i am back in business! I was actualy surprised at how well it worked, thank you!
lmfao, I just realized that I fixed my controller already years ago the exact same way. I had in my mind "wait, didn't you already fix this problem in the past?" but I wasn't sure. Now my bumper on new controller is not working again and I searched for a solution. And bam there it is, you bring me my memory back 😂
Thanks a lot!
Edit: And yes, the fix worked for years and even longer than the controller itself. On my old controller the fix is still working but the controller itself had to be replaced after such a long time of usage.
Thank you for saving me having to buy another controller. I broke one of the clips on the top-back of the left grip but that was my fault and a common occurance with anything clip based. Can barely tell its broken but I'd rather have that minor issue then have to buy a whole new controller. Thanks again, loved the screwdriver lmao
You’re a genius. It’s logical thinking and i was able to fix my controller. Saved me $50 bucks to buy a new one!
Thank you soooo much. This worked for me. The only thing i did differently was i added more layers of tape. You added 2 but i added 5 because my tape was really thin. Thank you again. You just saved me from buying another controller
Great and straight to the point. Ended up having to replace the bumper as it was broken.
Thx for this video, I can’t tell you how many times I’ve died in modern warfare because I couldn’t Stim myself😂
Mines jump. But just as essential lol. I play bumper jumper tactical. Game changer
@@alienman2540 dude same it works so much better
my rb is shoot, i’ve lost so many fights cause of this
I bought my XBOX back in 2019, as a BD present, but after finding this controller issue, I couldn't continue playing in my XBOX, until now! Thank you!
Blowing in between....what an easy fix I´ve been struggling with it for months. Thanks pal. I didn´t have to take it appart
Same here lol, can’t believe it worked
This video will give thousands of people the confidence to do this. Well done, Sir.
Like Geralt of Rivia, you are a true friend of Hugh Manatee (whoever that is)
Actually i dont know anything about this should i try this my rb is not registering properly.
Same did u figure it out
Karl what I did is pull back the LT/RT and then blow into the RB/LB. Somehow then both of this worked
@@marcot4395 did work for me
MarcoT43 blow ?
Try to blow into it. It help actually blow real hard hold down RT cause my RB wasn’t working either but if u blow real hard into it it should work
Bruh I blew air into it and it worked 🤣but I’ll still give you the watch time you deserve my good man 👏🏼👏🏼👏🏼
Here's a small tip:
If you don't want to permanently break a flat head screw driver, use a 5/64 bit. It works like a charm if you wedge it in there properly.
EDIT: You can also break off that stupid little center post and use a regular torx bit.
Ur an absolute icon, the bit about the bumpers and the plastic pieces that press the keys was where you got me, absolute legend
I did this and found out that my left back button was broken. I did order the button on amazon. Thank you.
A very informative video in a short format! Thanks to you I was able to repair my controller (it is a custom one so it really means something to me) keep it up!
Woohoo!
I'll definitely do this when i get the screwdriver. Thank you!
RedLine you so not need a screwdriver all you need is the floor and a good Throwing arm boom open
@@patrickbateman9897 lol
What type of screwdriver is that?
@@alinluca3436 Torx T8H
the little lb poker on the plastic bit you detach somehow separated from everything.. This guide plus a bit of super glue fixed everything. You are the best!
Because the quarantine I play MHW a lot and my rb started to be like this, and thanks for this video so I can mod it!!
I came back to mhw also, such a great game
This is the first time I have watched a youtube video on how to fix something and it actually works
You’re a blessing I was about to buy a new controller. I couldn’t find any other videos which didn’t involve buying new parts thank you :P
:))
What's crazy is the first fix he said that didn't work for him (Blowing into the controller with the trigger pushed down) worked for me first try! Couldn't be happier with this vid!
oh man ,thanks! Blowing the controller hard worked for me. Damn. I was one second to open all the shit up. haha
I can’t thank you enough, my left bumber wasn’t working. I blew into the gaps and it works now
Bro I was about to buy my third controller but u safe my day.
Same man. Problem was so annoying. At least now I don't have to waste more money on a new 1.
Ikr
you have saved me, my life, and my beloved blue controller. I will be forever grateful.
Thank you, I was thinking about buying a new button and soldering it in, but this is going to save me a lot of time and effort :)
When you said to blow I tried that. It actually worked. I think my controller is turned on in a different way now.
Thanks man! You are AMAZING! I play FIFA too so the defender switching was a nightmare! The only downside it that the clicking sound is considerably muted, but that's fine for me.
When I open my controller up the pin on the lb was snapped so I super glued it back on and it worked a treat! Great video btw
Absolutely worked on my right bumper. Really did wonders. Thanks a lot
PHEW! Thank god, I blew into it and now it works again, just what I was looking for, thank you so much mate 👍😊😊
I really wish xbox would just come up with a good controller we shouldn't have to be fixing our own controllers just to have them in a workable state however thank you for the fix you are brilliant
Oh man! I'v got a new controller recently and even didn't think that it would be so unexpected problem. I guess after nier automata this broke due to pressing too much hard this button. I couldn't imagine that I can break this controller that way. So thank you for solving this problem. Now I know what to do.
Blowing worked for a lol but the it stopped working again
Same
Where did he talk about blowing
@@kleinmorettifan Start of the video
@@dq8262 thanks
The lever on my RB that depresses the button was broken, so each press didn’t actually press the button. Some super glue on the cracked arm and an added piece of tape like you said to the end that presses the button and it now works better and smoother than before.
Many thanks, many many thanks!!
Side note: my LB, RB and Xbox button cover were attached slightly different. They come off independent of one another. Same method if you come across this, always use EXTREME CARE when handling this level of plastic, breaks easy. Good luck!!
This worked, thanks. 2 strips of electrical tape exactly. I already owned a security torx screwdriver from when I changed my analog sticks to metal ones 😁.
You controlldr still working with the tape?
@@JoseSanchez-wr7xh Fix gave out maybe about a month ago.
@@ubermesch4456 so it lasted a good 6 months?
imma be 100% honest here, ive been having issues with destiny not registering my melee but this helped completely, this will forever be saved to my playlist, rock on
THANKS SO MUCH, you just gained a sub and made my day! :)
My dude, you just saved us $50-65, maybe a few times over. Blessings to you!
I opened up mine and found that the piece that you put tape over had completely broken, all I did was open up my old controller that had working bumpers and switched them and I was ready to go
That blowing technique at the beginning actually worked, wow cheers!
Soooo how are you supposed to take out the battery pack of the xbox elite s2 😂😂 I'm on my 2nd one the 1st one had a bad lb now my rb on my 2nd one is broken and I never slam my controller or nothing
fr this is annoying
Oh my god, i was suffering with my controller for months, and when i tried the blowing solution, it work again like new. Thanks man
I'm scared to try this
THANK U SOOOO MUCH! It works for my controller, I was so scared to repair it cause it's an special edition from Gear of War but I saw your vid & did it, thank u again, you're awesome!
I blew it worked lol 😂
Hahaaa yes thats the first thing one should try
my right toggle was not working. I did the blow method and it worked. Thank you. You save me from getting another controller!
I was so sad my new control wasn’t working. You mentioned the blowing method and I gave it a try. Immediately worked. THANK YOU!!!🎉
I had the opposite problem. The switch was registering as always being pressed. It appears to have been that black plastic bar right above the switch holding it in. Wedging a thin plastic tool very VERY gently between the bar and the body of the switch seemed to relieve the pressure on the button. This video however still gave me a good look at how to open the controller and get at the shoulder buttons. Good vid.
I have the same issue, my LB button triggers on release or when I touch it VERY gently. It's impossible to play games with. I hoped there would be a software fix that could configure the sensitivity ...
Thank you so much I blowed into the little cavity thing and now it works your a legend and just earned a sub 🐐
This is a great example of an awesome tutorial. Bravo dude
Thanks for the video, we just saved a lot of money, didn't need the tape, just some isopropanol inside the button did the trick!
Wait how did you do that
PLs respond
The blowing actually worked, it didn’t at first then like 2 mins later it’s completely fine, idk what kinda wizardry that is but I’m impressed
This helped alot! The little prong that you extended in the video? It was broken on my controller! I've used two part glue to repair it so hopefully that'll give it an extension on its life! Thanks for taking the time to make this video!
Thank you so much!! 00:54 this blowing part is works for me.
Same
Hey guys! So this actually works. And no I’m not a robot or a fake account but this seriously works. I fixed mine today by firstly purchasing a T8 Screwdriver to get the screws out, then bought some black thick tape idk the name but it’s the black one that thick one and erm I put three layers on the thing this guy put the tape on and then put the controller back together and it works like a charm! I’ll make a video later on. Anyways THIS WORKS!
When you said you don’t recommend pulling the sticker off what else can we do? 1:22
Thank you EVER so much. I have bought controllers 1 or 2 times a year because of this and now I have 6 that I can repair and should never have to buy another.....except when I get the Series X....if ever. Thanks again!!!
I’ve never heard of the blowing method but somehow that did the trick😂 appreciate the video!
Thank you SO much! I JUST used this video to fix my RB on my controller. I had to take apart other, older controllers to use their bumper strip.
Tip for other people! if the USB inputs are different, (micro vs USB-c) then the connectors/inserts are different! You'll need to match USB inputs if you are taking parts from other controllers.
Active reload here I come! :D
i dint need to to open the controller i just blow the dust off and it works,
you just saved me 50 bucks.
THANKS!