Hey Darren, you just saved my bacon with this video. Just set up a F411WTE in a Zohd Drift (what a squeeze that was) ... Original Zohd 30A esc lite kept beeping rapidly... was unable calibrate using the sticks... Was just about to rip everything out and install a different Esc.... Tried this method and hey presto now working a treat... Thanks Darren 👍
Hi Darren, great video. Really glad to have found it. Especially the instructions with the flight controller. Had the problem with the Hee Wing Ranger T1 with 2 motors. Thanks and regards Didi
I learned something interesting the other day. This is probably all well known. Using a quad ESC on blheli configurator. There where 3 different types main, tail and multi. Switching from multi to main it spools up slower and it's preconfigured for low voltage shutoff braking was different also.
Interesting. I've never seen that before. But I use the BLHeli Suite rather than the Configurator; so maybe it's just in there. Definitely something to watch out for. Thanks :)
Thanks Darren great Video. I am a long range guy and now that the Eagletree Vector is End Of Life I have switched to iNav. The one glaring difference for me is that unlike ANY other flight controller I have used you cannot just go into a menu and set the battery capacity in the field. I know there are 3 Profiles you can use but seriously as a long range guy I have many different battery configurations that I use and it would be nice just to change the battery capacity in the field WITHOUT having to have a computer with me. Unless I am missing something ?
To be honest, it’s not something I’ve ever checked. I’ve seen profiles in the OSD Menu. But not dove in to see what you can change. I’ll take a look and see if something like that exists. If not, I’m sure it can be added.
Hello Darren, Just want to say how helpful all your videos have been for me. Would this issue show up on a turnigy 60am esc attached to a matek 743 flight controller at s2 with a single motor, getting a beep every 2 seconds continually when battery is plugged in????? I'm currently dealing with this now everything in plane works great except motor. Ill try what you showed on this video later today and hope it works. Any suggestions would be helpful.
Hello Darren! I have a full setup in my Bushmaster. when trying to calibrate the ESC, I can't switch the safety button when armed. If I disarm, I can go through the procedure, but the ESC continue to beep and nothing happens with the calibration.
When I connect and power the ESC and connect PWM wires to my Matek, my "outputs" page fails to let me use the manual control sliders or slide the Motor Test Mode Notice switch, which is grayed out. Does that switch remain deactivated if you don't calibrate your ESC first?
Jeśli gdzieś nie mogę znaleźć porady dotyczącej jakiegoś problemu czy to na wiki czy to na innych kanałach TH-cam lub forach. U Ciebie wszystko jest, i pozwala mi pokonać napotkane problemy. Dziękuje Ci bardzo za filmy, porady i Twoją prace. SUPER ROBOTA 👍💪👍💪👍
Just want to add that turnigy trouble shooting manual says that the constant beep 2 seconds apart says check transmitter and receiver. Doesn't make sense to me. all that is working as designed. Hmm I wonder if i should try plugging esc into s1??
Hi Joe. To be honest, I'm not a quad guy. On mine, DSHOT syncs the motors. I don't believe it has anything to do with the flight controller firmware. Maybe this is done through bi-directional DSHOT, which INAV doesn't support?
You need to find out what is blocking arming. In the CLI, type STATUS and press enter. It will return the codes of anything blocking arming. You can check them here github.com/iNavFlight/inav/wiki/%22Something%22-is-disabled----Reasons
Hello Darren, I got the brand new EDF RC Jet and trying to convert it into Digital FPV plane. I soldered the ESC's power and signal wires to the flight controller. And flashed the flight controller with INAV 6. I calibrated the ESC but the problem is that the motor isn't spinning and keeps beeping every second. On the radio transmitter, throttle min is trimmed at 1000 and max is trimmed at 2000. Any suggestion on how to resolve this issue? Here is the video demonstration of the problem: th-cam.com/video/75uxwvwFWP0/w-d-xo.html
Hey Darren, you just saved my bacon with this video. Just set up a F411WTE in a Zohd Drift (what a squeeze that was) ... Original Zohd 30A esc lite kept beeping rapidly... was unable calibrate using the sticks... Was just about to rip everything out and install a different Esc.... Tried this method and hey presto now working a treat... Thanks Darren 👍
Great How to Mr D now instead of me Explaining I can just share this Video
Take Care
Thanks Robert 👍🏻
new to wings! this was just what i needed! thank you
Hi Darren, great video. Really glad to have found it. Especially the instructions with the flight controller. Had the problem with the Hee Wing Ranger T1 with 2 motors. Thanks and regards Didi
Super useful, Darren. Thanks
Thanks Silvio. Hope you're having a great week :)
This is so helpfull! Thanks Darren!
Thanks Ard. Glad it was helpful.
I learned something interesting the other day. This is probably all well known. Using a quad ESC on blheli configurator. There where 3 different types main, tail and multi. Switching from multi to main it spools up slower and it's preconfigured for low voltage shutoff braking was different also.
Interesting. I've never seen that before. But I use the BLHeli Suite rather than the Configurator; so maybe it's just in there. Definitely something to watch out for. Thanks :)
Thanks Darren great Video. I am a long range guy and now that the Eagletree Vector is End Of Life I have switched to iNav. The one glaring difference for me is that unlike ANY other flight controller I have used you cannot just go into a menu and set the battery capacity in the field. I know there are 3 Profiles you can use but seriously as a long range guy I have many different battery configurations that I use and it would be nice just to change the battery capacity in the field WITHOUT having to have a computer with me. Unless I am missing something ?
To be honest, it’s not something I’ve ever checked. I’ve seen profiles in the OSD Menu. But not dove in to see what you can change. I’ll take a look and see if something like that exists. If not, I’m sure it can be added.
Hello Darren, Just want to say how helpful all your videos have been for me. Would this issue show up on a turnigy 60am esc attached to a matek 743 flight controller at s2 with a single motor, getting a beep every 2 seconds continually when battery is plugged in????? I'm currently dealing with this now everything in plane works great except motor. Ill try what you showed on this video later today and hope it works. Any suggestions would be helpful.
perfect, thanks!!
Hello Darren! I have a full setup in my Bushmaster. when trying to calibrate the ESC, I can't switch the safety button when armed. If I disarm, I can go through the procedure, but the ESC continue to beep and nothing happens with the calibration.
thenks
When I connect and power the ESC and connect PWM wires to my Matek, my "outputs" page fails to let me use the manual control sliders or slide the Motor Test Mode Notice switch, which is grayed out. Does that switch remain deactivated if you don't calibrate your ESC first?
Have you enabled motor and servo outputs?
Any ideea on how to calibrate a reversible esc for a rover in inav? Thank you!🙏🏼
When I use a blheli_s /32 esc with dshot should I change the protocol to dshot, or can I keep it standard?
You should change the protocol to DSHOT. You should keep it DSHOT 300 or below.
Jeśli gdzieś nie mogę znaleźć porady dotyczącej jakiegoś problemu czy to na wiki czy to na innych kanałach TH-cam lub forach. U Ciebie wszystko jest, i pozwala mi pokonać napotkane problemy. Dziękuje Ci bardzo za filmy, porady i Twoją prace. SUPER ROBOTA 👍💪👍💪👍
Just want to add that turnigy trouble shooting manual says that the constant beep 2 seconds apart says check transmitter and receiver. Doesn't make sense to me. all that is working as designed. Hmm I wonder if i should try plugging esc into s1??
I have the Nighthawk quad running iNav 4.1 with a Matek F722 STD FC - how do I sync all the motors to start at the same time...joe
Hi Joe. To be honest, I'm not a quad guy. On mine, DSHOT syncs the motors. I don't believe it has anything to do with the flight controller firmware. Maybe this is done through bi-directional DSHOT, which INAV doesn't support?
I'm have one question ! Is that inav won't spin the motor when no GPS in a Plane ?? when i'm Arm the swicth ..
You need to find out what is blocking arming. In the CLI, type STATUS and press enter. It will return the codes of anything blocking arming. You can check them here github.com/iNavFlight/inav/wiki/%22Something%22-is-disabled----Reasons
Two motors and esc's would be the same procedure?
Yes, its the same.
@@MrD Thanks you
Bro i need your help I tried to connect dji naza v1 to mamba Dshot600 4in1 esc but its not working please help its works well with simok escs
Sorry, I don’t know much about that system. It’s pretty old, so does it support DSHOT?
Got a quick short of a problem I'm having & explanation in comments. My only vid.
please motor1 not output when i control transmitter
Только здесь я понял почему пищит непрерывно мой двигатель, спасибо.
Рад, что смог помочь
Hello Darren,
I got the brand new EDF RC Jet and trying to convert it into Digital FPV plane.
I soldered the ESC's power and signal wires to the flight controller. And flashed the flight controller with INAV 6. I calibrated the ESC but the problem is that the motor isn't spinning and keeps beeping every second. On the radio transmitter, throttle min is trimmed at 1000 and max is trimmed at 2000.
Any suggestion on how to resolve this issue? Here is the video demonstration of the problem: th-cam.com/video/75uxwvwFWP0/w-d-xo.html