From someone who is a painter, don’t get so hung up on not sanding through your primer. Your first primer coat should be viewed as sacrificial, you actually want to sand through most of it because that allows your scratches and everything that you were trying to fill to then build up to the level of everything else. If you just lightly sand everything and rely on your sense of touch, you’ll miss a lot of scratches and things won’t get filled in as efficiently. You will end up having to fill/sand/fill more often than if you just more aggressively sanded down the primer coat, revealing all of your areas that still need more work. There is no need to “polish“ the primer, because you’ll be painting over it anyway. 220 scratches will get filled up by spray paint, especially filler/primer so for buildable paint/film finishes, no need to really sand past 220. Great result! Looks amazing!
I was coming to the comments section just to say about the first sacrificial primer coat. It's meant to show where your high spots are. Edit: Removed an unnecessary duplicate "where".
I sand with 160 grit, and naked PLA feels like matte polished ivory. It's an AMAZING look/feel: it makes a "cheap" feeling 3D printed part feel very luxurious.. It's amazing.
I find that wet sanding saves you a LOT of sandpaper, you can use it for much longer than if you sand it dry. I usually add a couple of drops of dish soap to the water as well so when I'm done sanding I can just rinse it in water and it's nice and clean and ready for paint.
Couple quick swipes with a sandpaper eraser will probably extend the sandpaper life too. I doubt the abrasive is deteriorating sanding plastic the same way it does on wood or metal, so it's probably just gumming up.
Depends also a lot on the type and brand of paper used. I switched from regular DIY store paper to Mirka Gold and that stuff tends to stay "open" much longer and also does not dull as fast. I only use wet sanding on the lacquer.
Update, That last step when you water down the wood filler, chef kiss, I needed that to perfect my technique. These last minutes worth the whole video. Much appreciated my friend.
Resin printers are a pain, I know. But I'd way rather deal with it than sanding and filling and sanding. I'd lose all the detail, and it would be *way* more work!
after 12 years of 3d printing i just use floor varnish, works just like wet sanding , it takes a long long time but much better on my wrists at 55 and its cherry smooth
Earned a sub. I've picked up most of the components of this from people (Use sandable primer, try wood paste, ect) but no one actually goes into how to use them all in a standard workflow. Appreciated, definitely going to be improving results
Great video! Awesome tricks that will help anyone looking to make their 3D prints look smooth, thanks for sharing this! There's one more step I do in the beginning before sanding that you might like to try as it's a big time saver. Get some fiberglass resin (bondo brand, or whatever is on the shelf at the store) and mix it up and pour it over your print and let it cure overnight before sanding. The resin will "self-level" and do a lot of smoothing for you. Most importantly, the resin sands SO MUCH EASIER and your initial sanding time will be slashed to seconds or minutes and no dremel needed. Trying to sand plastic is just generally difficult, so i recommend the resin route. There's a product made specifically for this that I forget the name of, but in my experience the fiberglass resin off the shelf at your local department store is cheaper and more effective. As an added bonus it gives some strength, too, while also being a better surface for the primer to bind to. Give it a try, I think you'll like it!
The product you're looking for is probably XTC-3D or 3D-Gloop. I have the first one and it is a two component mixture (resin + hardener). After applying it to my prints the gaps were filled and it got the glossy finish. It's also much easier to sand.
One suggested change to your process, use primer/filler first. That builds up the surface so you’re sanding away less PLA and more filler. You get less melt and it’s quicker to sand. I go back and forth with primer/filler and sanding. Very little putty filler is need
@@V3lv3n sticks plenty fine for me honestly.. if im superglueing parts down i already sand them to almost bare pla best i can then apply glue. otherwise sticks perfectly fine for non structural parts
These are great tips. I'm lucky in that while I'm only new to 3d printing I was into radio control cars, boats and planes for close to 40 years. I used to build model cars as a kid as well and then in HS I started in auto-body. Filling and smoothing is second nature to me. lol One of the tricks my auto shop teacher taught me (something like 35 years ago) is to use a mix of 2 part epoxy and methanol to thin it out and add in corn starch as a filler. You can use baking soda but it is coarser than then starch is. I use this to paint on a layer and let it cure for a few days to fully allow the methanol to evaporate. It sands well and I can get all of it at my local dollar store. It takes paint very well too. I like to mix the part A (the resin) with the methanol to thin it down and then add in the starch until it's like pancake batter then add in part B (the hardener). If it's too thin add more starch. If too thick more methanol. It also has that side benefit of leaving a very "plastic" looking surface.
@@ItsMeaDMaDe My pleasure. As an add-on you can play with it a bit by using various cure time epoxies. The longer the cure can really let the epoxy smooth out. I personally prefer a 20 minute set.
Very great guide! Would've been extremely helpful back when i still did FDM printing. One thing i would recommend to avoid primer build up: if you have an airbrush, use it! I used to hate the priming phase because i would always get splotchy awful coats on my model until i switched to using airbrush primer. not only do you have way more control on how the primer is applied, you also have significantly shorter wait times which means you can prime, evaluate the model and then get right back to sanding/scraping without having to wait 2-4 hours, or in my case, until the next morning because of my climate (cold af) Another thing I'd recommend is to get yourself a scraper card or a burning tool to take away the first layer lines. I suggest getting the one that looks like a hobby knife. it's been a total game changer for me and what took me 4 hours of sanding I can get done in like 30 minutes. Anyway thanks for the video! I wouldn't say i learned anything new, but having 1 video that tells you all the tricks instead of having to watch several dozens to get the same information will be a huge boon to beginners.
Thanks for the tips. I actually do have an airbrush I use it a ton. But a lot of people don’t have airbrush’s so for this video I used rattle cans. I’ll have to look into that scraper. Thanks again!
Do you happen to have a tip for preventing the tacky texture on primer? I may just be using too much paint, but it's a pain that it's tacky until it's been handled all over even after drying
The result is amazing! thanks for sharing the process with so much detail. I have ZERO experience painting 3D prints (unless just going with acrylics on top of the PLA....I know), but in the comments there seem to be people giving good ideas mostly related to get something similar with less effort and steps (so faster lets say). SO....IF you ever run out of ideas for videos, let me do a suggestion: a video post processing the same model (a new print of course), but using some of the advice to see how good it really works. Either the end result is fast and good or not, the experiment would be beneficial for everyone (including you, mostly if you discover a faster/easier workflow, and if not, you can say "told you guys" lol). Cheers and thanks for the incredible hard work you are putting with this channel, I already learnt a lot from you.
Came out great! I usually do a light sanding of the print at first followed up by two coats of primer that has filler in it. After that I do one more round of light sanding followed up by one final coat of primer with filler and the end result is ultra smooth like resin. I just bough a heat knife and might try that out to remove the support marks from the prints also. I also use a small container of automotive putty to do any patchwork if needed but most of the time I do not need to.
Hey, really informative video. I've watched a lot of how to videos on finishing 3d prints and one thing that I have never seen anyone highlight is the use of diamond nail files as an abrasive. I use them all the time, they are thin and come in multiple grits and never wear out. they have saved me money on abrasives for sure.
Great vid and info, thanks. i have a nail drill (used for doing manicures/pedicures). It's a lot more delicate than a rotary tool like a Dremel and i suspect a lot of the attachments might be useful (and interchangeable with a rotary tool if one does not have a nail drill) because the attachments are made for doing things like acrylic nails and nail polishes.
Sanding tip if you enjoy keeping soft hands. Put blue painters tap on sand paper to hold it to the block and on the sponge. This smooths out the sand paperwork so you dont sand your finger pads too
Yup - that's (just) the classic process of model-making/finishing: all design prototypes, be it from wood, cast resin, laminated fiberglass or renshape are finished this way. Investing in a good (automotive) filler pays off. 2K Polyester putty is usually a better way than air-drying wood filler.
Here goes a tip of something that I do and works perfectly. When you need to fill cracks or something else of your print, use a brush and water to mix the putty, and apply that wet mix in your print as if you were painting it, it's way more easy and fast.
Give card scrapers or using utility knife to scrape smooth sections a try. It's a definite improvement over just sanding. I use it in nearly all my post-processing, along with 2k high build primers over plain rattle-can primers. They aren't for everyone, but when I want a really smooth and durable surface as my paint base, it's what I go to these days.
@@Feibie yeah you take flat metal and create a microburr that you can use to plane the rough parts down. It works incredibly well, but not in *every* situation :)
Hi Chris, great work. I'm hoping to print this out and I'm going to follow all your steps to paint it cartoon style. I do have an unrelated question though. Where did you get that Fantastic Four Thing bust on your shelf over your left hand shoulder? It looks really cool and I'd love to make one of those too
@@DUSKtillDAN666 few weeks ago I did that as a project. I got it from inspy3d. Great guys here is the link to their site. They also have a patreon where you can get all their models. inspyr3d.com/
Instead of a deburring tool, I've had really good results using the grinding stone bits on a dremel. You have to be careful about melting the PLA if it digs in at all, but that isn't _that_ hard to avoid after only a bit of practice. But while it's faster on really rough stuff than most normal sanding, it's not quite aggressive as the deburring bits.
great video! you can sand more finely before the first coat of primer. I generally go down to 120 180 before. I can even go up to 220 if the object has a lot of flat surface. I waste less primer like that. To fill the holes, I use wood putty, it dries quickly, but it gets hollow when it dries (so you have to be generous)
I thought I was going to learn some special technique aimed at FDM printing in particular.Got a long vid on sanding 101. But I'm not mad about it, this vid is very well done. So many good techniques for good sanding. And a lot of ppl need this very well done breakdown.
I have wondered at how well 3D prints worked up. This is some very useful and instructive information, Thank You for sharing with Us here on the tube! I had considered such a machine, but, having recently retired I haven't much fun money to play with. (I spent it all on model kits and createx paint.) I look forward to Your videos and again, Thank You for Your time and consideration with the videos. Oh and Your mustache is kicking it!! I have one like it as well!! Later
To lessen sanding, what I do is spray primer, sand, second primer, sand, and a third final primer, and a final sanding. The first primer fills up the layer lines. The second primer fills up anything I missed or gets exposed on the first sanding. The third fills everything up. You don't even need to sand hard. Just buy one of those sandpaper sponge and just sand away while you're watching something. Sounds like a hassle but its fairly easy. You could be done with it in 30 minutes for even for minis.
This is the technique I use for my prints, NOW I love printing Anime Figures and other stuff with lots of texture So you can always do a mix and print the large parts on PLA and the face or parts with more texture with resin, it will save you tons of time and money in the long run.
Watched several of your videos and thanks they are great. I had a question though. I have carpal tunnel and have a hard time sanding for long periods. I have been looking into using resin to lessen the amount i need to sand but do you have any tips on reducing sanding or making it a bit easier. Mainly its about having to grip for long periods of time.
ever tried smoothing prints with a soldering iron i have been doing it with amazing results even use it to fill in gaps melting plastc back into place and you now get irons with differnet shaped top so form in detail of prints
Your patience got rewarded with the quality look of the finished product. Well done! However, what is the point of printing the object in their intended colors if they will be sanded down for clean-up and then repainted?
really nice video. It is nice to see the whole and long process. Often this is just mentioned as doing a lot of sanding and priming, but I better understand the efford after watching this. You got yourself a new subscriber :)
This is a great step by step demonstration. My only suggestion is that on a really roughly printed area it might be worth double-checking the original model. I think you filled and sanded away the thin bottom edge of the cap. Don't listen to the haters. Not everybody has a resin printer. I rarely even use mine because I don't have dedicated space to set up a stinky chem lab. Besides, at this scale I'd say the PLA print was cheaper and considerably more sturdy. There's nothing wrong with putting in the work to make it look nice.
Thanks so much for the comment. I did check the model there wasn’t much of an edge to it. I tried to make it more defined. As for the haters. Yeah… this is a video on pla and good finishes. There are way more people with fdm and not resin printer for so many reasons like they have little kids in the house or afraid of the safety issues. If found the people that switch to resin rarely go back to fdm. But this video isn’t for them which doesn’t hurt my feelings when most people just say use resin without thinking of reasons people don’t use it. Oh well the world we live In. I appreciate your comment. Thanks again!
Ignore the haters, I think most of them lack the patience to do what you've done. I was going to ask if you'd considered using acetone? If you brush it over PLA models, it will smooth out a lot of the layer lines. Should save a lot of time.
@@stewburt5089 thanks! So acetone works on abs prints but not pla at least the times I’ve tried it. It might depending on the brand or type if you have gotten it to work. The one thing I should of said in the video is this is for people that don’t have or can’t have resin printers. Most of the comments are just telling me to print in resin and that wasn’t the point of this… oh well.
I'll start off by saying, I enjoyed this video. I'm only just getting into 3D printing, so still researching and I only found out about resin printers today and, like I'm sure it is with most people, I thought it was magic, especially compared to PLA printing! So it got me thinking "do people stick with the lines of PLA printing, or do they work on making it look better" and I came across your video and it answered my question, yes you can work on it to make it look better.... But the amount of time it takes makes me think people probably don't lol. I still have some unanswered questions though, do people usually not paint their 3D printings? I wonder this because there's so many different colors of filament, but it'd look so much better painted right? Oh and also does the quality of the printer make the lines less obvious? Or is it just a thing that'll always happen with that type of printing.
So some people are just getting into 3d printing and don't know how to smooth their prints! Wow, I can't believe you didn't know this. It changes my whole attitude about you. Idiot
@cecilepuckhaber1067 are some people using their hands for the first time? Sanding is not a new concept and is practically used on most metals and woods you see when you walk around, this is like learning your drainage leads to the city sewer, you should already know this you dunce.
Like a lot of people, I'm choosing whether print accuracy or print aesthetics takes priority. On parts that have a high mechanical tolerance, that generally means that the support areas are going to be what everyone sees and and may need considerable clean up. For tight spaces consider looking into mini diamond files. That helps a bit but still not a perfect solution. I really want to give sandblasting a try but don't really have the space for one. Resin printing is not suitable for mechanical function in most cases. It's far too brittle. I've researched buying an SLS printer but a small format machine that would fit into a small residential workspace is still near $30k. Maybe someday.
Wow this was a great video, I just had to subscribe. And a thumbs up as well. I am really new to this hobby of 3D printing so any tid bit of knowledge shared is greatly appreciated. Thank you so much and great stache !
i just use thicker (not to thick but not water like) primer based on acetone without sanding then sand it , its waaaay easier because you already have filled layers just need to make it smooth and then aply thin primer 10times faster than any other method
How many hours of post print work for the final finished painted product? Just curious what the reality is on how long it takes after the printing is done, to get this kind of result?
Just some advice for those who want to start sanding their projects, you may want to increase your number of permitters if you have a rough or bigger part that will require more sanding. It is not normally necessary but if you have a part that requires a lot of sanding, you can wear all the way through if you are not careful (assuming you are running default print settings with 2 shells). I think most people can get by by focusing on the primer (if youre sanding for aesthetics- most of my sanding is for dimensional accuracy so take this with a grain of salt) but you might want to give yourself some buffer on your first print or two.
I was wondering about that. I had a part I printed and only sanding a small amount I went through the wall enough to weaken the part and broke it. With sanding 80 grit, I would expect that the walls have to be much thicker than most normal parts. I don't get the point of 3d printing things though if you're going to have to spend hours sanding and finishing. Seems like it just completely defeats the point of 3d printing.
It seems you prime all the respective mortise and tenon faces for each piece and seem to avoid those areas when painting (and sometimes use silly putty for holes). It seems to me that plastic to plastic gluing would be better than paint-glue-paint. Or doesn't that matter?
Coming from other finishing FDM prints videos, they diulute bondo with acetone and uses it as a filler primer, but its thicker. Maybe the plastic wood and water could be shoot with an airbrush in order to keep the thickness to a minimum and speed a bit the process ?! Just an idea. Also, how long would you say it takes to sand and prep ready for paint a model this size ?
That’s an interesting idea to try to spray it. The whole process of sanding and priming took about 5 hours. That includes all the dry times I had. Which could of been half of the actual time.
As someone that also have a resin printer, I just put thin layer of resin over the PLA model, cure it, rinse and repeat until most of the layer lines are gone.
Are there any good products to fill in gaps on functional parts that will handle a lot of shock and abuse? Have been looking for something that will truly fuse to the plastic and become part of it and not something that will just crack, chip, flake, scratch, etc...
I’m amazed that every video on YT I have watched regarding sanding, not one mentioned the most important step of sanding which is done post sanding, and that’s cleaning the dust and ensuring the surface is clean before adding any paint or putty.
would you get better results, or maybe faster, if you use acetone vapor to smooth it out? I don't know if it would make it easier to get to those places that you were having trouble reaching.
Hi I saw your video with my son and we loved it, he's a big Mario Fan, so ofc he wanted to print this model. But the link doesn't exist and more. I also used Yeggi to search for it but i couldn't find it. Would you mind pointing me in the right direction. Thanks in advance
Inspector Clouseau I presume? Just a tip, your Goatie is a bit wind swept to the left from where I sit but your right, it should be 100% semetrical, i.e, 50% left and 50% right, it helps if you could count the hair exactly to get a perfect look! LOL!
Got any tips videos for printing multiple models on the same plate? Getting excessive stringing between the models and they are at last 30mm apart. Maybe turn off coasting?
@@jesseburson stringing: filament is pouring out of the nozzle when you don’t want it to. Increasing the gap will only make it worse if you don’t solve the problem.
I slice it normally I typically do this process on certain models especially if the supported areas aren’t as clean as I need them to be. Sometimes I might just do a light sanding and primer with no putty. I have a Cura series where I go over the settings I check for every print.
switch to UV putty, it dries in like 10~30 sec with UV light. u can get those thin sanding sponges instead of the big blocks, those work better for rounded surface. tho the grids ar higher, i think they ar around 400 800 1000/1200. You can also get scriber for modeling to carve those hard lines so you can ink later.
Sanding is definitely the most common that I still use, thanks for the techniques and tools! Im aware of other methods like flex/hard resin dipping, latex dipping, XTC epoxy, Acetone fume polishing (this one's interesting), Chinese ultra fast PLA polisher (very interesting unknown material), oven baking (risky), and a few others
I got a battery powered Hyper tough "dremel" 8 volt version with variable speed...Single best thing I ever got for3D printing and was only 25 bucks. Actually very well built too! Ordered a bunch of various bit of amazon and I'm set. I HIGHLY recommend that thing! Awesome video too BTW...I ordered a set of those sponges too now. Im now a new sub also...Thank you
From someone who is a painter, don’t get so hung up on not sanding through your primer. Your first primer coat should be viewed as sacrificial, you actually want to sand through most of it because that allows your scratches and everything that you were trying to fill to then build up to the level of everything else. If you just lightly sand everything and rely on your sense of touch, you’ll miss a lot of scratches and things won’t get filled in as efficiently. You will end up having to fill/sand/fill more often than if you just more aggressively sanded down the primer coat, revealing all of your areas that still need more work. There is no need to “polish“ the primer, because you’ll be painting over it anyway. 220 scratches will get filled up by spray paint, especially filler/primer so for buildable paint/film finishes, no need to really sand past 220. Great result! Looks amazing!
Great tips! Thanks for sharing!
I was coming to the comments section just to say about the first sacrificial primer coat. It's meant to show where your high spots are. Edit: Removed an unnecessary duplicate "where".
For bodywork we use a guide coat on top of the primer and it settles into low spots and very easy to see.
@@LearnEverythingAboutDesign So that would be something like a white primer, then a thinned topcoat?
Good advice!
I sand with 160 grit, and naked PLA feels like matte polished ivory. It's an AMAZING look/feel: it makes a "cheap" feeling 3D printed part feel very luxurious.. It's amazing.
The determination and GRIT required to smoothen these parts are commendable
So nothing new just a lot of sanding, what a surprise 😅
40 minutes saved
Thanks - your comment was top - saved wasting my time 😂
What are you sending?
Wow just commented also its not right the image title of the video PLA LOOKS LIKE RESIN
Ty sir..... Saved me 40 min of this guy's ridiculous mustache. Ty ty ty
I find that wet sanding saves you a LOT of sandpaper, you can use it for much longer than if you sand it dry. I usually add a couple of drops of dish soap to the water as well so when I'm done sanding I can just rinse it in water and it's nice and clean and ready for paint.
Couple quick swipes with a sandpaper eraser will probably extend the sandpaper life too. I doubt the abrasive is deteriorating sanding plastic the same way it does on wood or metal, so it's probably just gumming up.
Depends also a lot on the type and brand of paper used. I switched from regular DIY store paper to Mirka Gold and that stuff tends to stay "open" much longer and also does not dull as fast. I only use wet sanding on the lacquer.
Update, That last step when you water down the wood filler, chef kiss, I needed that to perfect my technique.
These last minutes worth the whole video. Much appreciated my friend.
Yeah! That is one of my secrets. Glad I could share.
Step 1: sand
Step 2: sand
Step 3: sand
Step 4: buy a resin printer for resin looking prints
Probably the size of the sculpture can be a problem. But a idont know.
but then skip the get it really wet step
step 5: deal with messy resin printing process.
@@tinobabbage1350 Not really, as he printed it in small parts anyway
Resin printers are a pain, I know. But I'd way rather deal with it than sanding and filling and sanding. I'd lose all the detail, and it would be *way* more work!
after 12 years of 3d printing i just use floor varnish, works just like wet sanding , it takes a long long time but much better on my wrists at 55 and its cherry smooth
Earned a sub. I've picked up most of the components of this from people (Use sandable primer, try wood paste, ect) but no one actually goes into how to use them all in a standard workflow. Appreciated, definitely going to be improving results
I liked the nick in the shoe. It gives a nice detail.
7.5 minutes until he actually starts sanding, and that’s it. Sand your prints.
Thanks. I was 1.5 mins in and done lol. 😂😂😂
Modelling sanding files and sticks is your best bet for precise sanding and into difficult areas.
Great video! Awesome tricks that will help anyone looking to make their 3D prints look smooth, thanks for sharing this! There's one more step I do in the beginning before sanding that you might like to try as it's a big time saver. Get some fiberglass resin (bondo brand, or whatever is on the shelf at the store) and mix it up and pour it over your print and let it cure overnight before sanding. The resin will "self-level" and do a lot of smoothing for you. Most importantly, the resin sands SO MUCH EASIER and your initial sanding time will be slashed to seconds or minutes and no dremel needed. Trying to sand plastic is just generally difficult, so i recommend the resin route. There's a product made specifically for this that I forget the name of, but in my experience the fiberglass resin off the shelf at your local department store is cheaper and more effective. As an added bonus it gives some strength, too, while also being a better surface for the primer to bind to. Give it a try, I think you'll like it!
This is a great tip I’ll have to give it a try. Thanks for sharing.
The product you're looking for is probably XTC-3D or 3D-Gloop. I have the first one and it is a two component mixture (resin + hardener). After applying it to my prints the gaps were filled and it got the glossy finish. It's also much easier to sand.
One suggested change to your process, use primer/filler first. That builds up the surface so you’re sanding away less PLA and more filler. You get less melt and it’s quicker to sand. I go back and forth with primer/filler and sanding. Very little putty filler is need
Good point.
Dont you need to lightly sand the surface to have the primer stick anyways?
@@V3lv3n sticks plenty fine for me honestly.. if im superglueing parts down i already sand them to almost bare pla best i can then apply glue. otherwise sticks perfectly fine for non structural parts
I love Chris he’s right on the mark covers everything
Thanks so much. Glad I’m not disappointing.
These are great tips. I'm lucky in that while I'm only new to 3d printing I was into radio control cars, boats and planes for close to 40 years. I used to build model cars as a kid as well and then in HS I started in auto-body. Filling and smoothing is second nature to me. lol One of the tricks my auto shop teacher taught me (something like 35 years ago) is to use a mix of 2 part epoxy and methanol to thin it out and add in corn starch as a filler. You can use baking soda but it is coarser than then starch is. I use this to paint on a layer and let it cure for a few days to fully allow the methanol to evaporate. It sands well and I can get all of it at my local dollar store. It takes paint very well too. I like to mix the part A (the resin) with the methanol to thin it down and then add in the starch until it's like pancake batter then add in part B (the hardener). If it's too thin add more starch. If too thick more methanol. It also has that side benefit of leaving a very "plastic" looking surface.
That’s a great tip I’ll have to give that a try on some prints. Thanks!
@@ItsMeaDMaDe My pleasure. As an add-on you can play with it a bit by using various cure time epoxies. The longer the cure can really let the epoxy smooth out. I personally prefer a 20 minute set.
I'd prime first. It will fill all the little valleys. That way, you need to sand only half as much. Then spray primer again.
thanks for teaching me how to sand for 30 minutes.... in all seriousness this looks awesome you just have a lot of time on your hands
Very great guide! Would've been extremely helpful back when i still did FDM printing.
One thing i would recommend to avoid primer build up: if you have an airbrush, use it! I used to hate the priming phase because i would always get splotchy awful coats on my model until i switched to using airbrush primer. not only do you have way more control on how the primer is applied, you also have significantly shorter wait times which means you can prime, evaluate the model and then get right back to sanding/scraping without having to wait 2-4 hours, or in my case, until the next morning because of my climate (cold af)
Another thing I'd recommend is to get yourself a scraper card or a burning tool to take away the first layer lines. I suggest getting the one that looks like a hobby knife. it's been a total game changer for me and what took me 4 hours of sanding I can get done in like 30 minutes.
Anyway thanks for the video! I wouldn't say i learned anything new, but having 1 video that tells you all the tricks instead of having to watch several dozens to get the same information will be a huge boon to beginners.
Thanks for the tips. I actually do have an airbrush I use it a ton. But a lot of people don’t have airbrush’s so for this video I used rattle cans.
I’ll have to look into that scraper.
Thanks again!
Do you happen to have a tip for preventing the tacky texture on primer? I may just be using too much paint, but it's a pain that it's tacky until it's been handled all over even after drying
I actually use files for my initially sanding…makes life very easy, and with micro files you can get into those small areas
WOW sanding. What a new and fascinating concept
I got here by accident and algorithms. But is nice you share this to the new makers. I also get some tips here and there. Thank you pal.
No problem glad I could share it
The result is amazing! thanks for sharing the process with so much detail. I have ZERO experience painting 3D prints (unless just going with acrylics on top of the PLA....I know), but in the comments there seem to be people giving good ideas mostly related to get something similar with less effort and steps (so faster lets say). SO....IF you ever run out of ideas for videos, let me do a suggestion: a video post processing the same model (a new print of course), but using some of the advice to see how good it really works. Either the end result is fast and good or not, the experiment would be beneficial for everyone (including you, mostly if you discover a faster/easier workflow, and if not, you can say "told you guys" lol). Cheers and thanks for the incredible hard work you are putting with this channel, I already learnt a lot from you.
Came out great! I usually do a light sanding of the print at first followed up by two coats of primer that has filler in it. After that I do one more round of light sanding followed up by one final coat of primer with filler and the end result is ultra smooth like resin. I just bough a heat knife and might try that out to remove the support marks from the prints also. I also use a small container of automotive putty to do any patchwork if needed but most of the time I do not need to.
I think that’s the great thing about this hobby there are so many different ways to do everything. Thanks for sharing your process!
Hey, really informative video. I've watched a lot of how to videos on finishing 3d prints and one thing that I have never seen anyone highlight is the use of diamond nail files as an abrasive. I use them all the time, they are thin and come in multiple grits and never wear out. they have saved me money on abrasives for sure.
Great vid and info, thanks. i have a nail drill (used for doing manicures/pedicures). It's a lot more delicate than a rotary tool like a Dremel and i suspect a lot of the attachments might be useful (and interchangeable with a rotary tool if one does not have a nail drill) because the attachments are made for doing things like acrylic nails and nail polishes.
amazing result! It's crazy what surface finishing can do
I finally subed. Took me long enough. You are a legend
Sanding tip if you enjoy keeping soft hands. Put blue painters tap on sand paper to hold it to the block and on the sponge. This smooths out the sand paperwork so you dont sand your finger pads too
i have to admit that mario looks smooth af...
Yup - that's (just) the classic process of model-making/finishing: all design prototypes, be it from wood, cast resin, laminated fiberglass or renshape are finished this way. Investing in a good (automotive) filler pays off. 2K Polyester putty is usually a better way than air-drying wood filler.
Here goes a tip of something that I do and works perfectly. When you need to fill cracks or something else of your print, use a brush and water to mix the putty, and apply that wet mix in your print as if you were painting it, it's way more easy and fast.
That tip is in the video! 😅
@@ItsMeaDMaDe I didn't see a brush 🤔
Give card scrapers or using utility knife to scrape smooth sections a try. It's a definite improvement over just sanding. I use it in nearly all my post-processing, along with 2k high build primers over plain rattle-can primers. They aren't for everyone, but when I want a really smooth and durable surface as my paint base, it's what I go to these days.
That’s awesome I’ll try it out. Thanks for the tip!
Are they the ones with a bur?
@@Feibie yeah you take flat metal and create a microburr that you can use to plane the rough parts down. It works incredibly well, but not in *every* situation :)
Hi Chris, great work. I'm hoping to print this out and I'm going to follow all your steps to paint it cartoon style. I do have an unrelated question though. Where did you get that Fantastic Four Thing bust on your shelf over your left hand shoulder? It looks really cool and I'd love to make one of those too
@@DUSKtillDAN666 few weeks ago I did that as a project. I got it from inspy3d. Great guys here is the link to their site. They also have a patreon where you can get all their models.
inspyr3d.com/
Instead of a deburring tool, I've had really good results using the grinding stone bits on a dremel. You have to be careful about melting the PLA if it digs in at all, but that isn't _that_ hard to avoid after only a bit of practice. But while it's faster on really rough stuff than most normal sanding, it's not quite aggressive as the deburring bits.
Very good work, but I would never have all that patience!
Ha ha. Yeah it takes a lot of patience. It’s relaxing to me though.
great video! you can sand more finely before the first coat of primer. I generally go down to 120 180 before. I can even go up to 220 if the object has a lot of flat surface. I waste less primer like that. To fill the holes, I use wood putty, it dries quickly, but it gets hollow when it dries (so you have to be generous)
I thought I was going to learn some special technique aimed at FDM printing in particular.Got a long vid on sanding 101. But I'm not mad about it, this vid is very well done. So many good techniques for good sanding. And a lot of ppl need this very well done breakdown.
Finishing parts is....... 1:50 - Setup/Settings:SandingSandingSanding
I have wondered at how well 3D prints worked up. This is some very useful and instructive information, Thank You for sharing with Us here on the tube! I had considered such a machine, but, having recently retired I haven't much fun money to play with. (I spent it all on model kits and createx paint.) I look forward to Your videos and again, Thank You for Your time and consideration with the videos.
Oh and Your mustache is kicking it!! I have one like it as well!! Later
They are fun to have but they do cost money to run for sure. Thanks for the comment. As for the stash glad I’m not the only 😂
To lessen sanding, what I do is spray primer, sand, second primer, sand, and a third final primer, and a final sanding. The first primer fills up the layer lines. The second primer fills up anything I missed or gets exposed on the first sanding. The third fills everything up. You don't even need to sand hard. Just buy one of those sandpaper sponge and just sand away while you're watching something.
Sounds like a hassle but its fairly easy. You could be done with it in 30 minutes for even for minis.
Thank you for the video!
May I ask what Printer and Nozzle size you used? Can you also go with a smaller nozzle size to reduce the layer line look?
This is the technique I use for my prints, NOW I love printing Anime Figures and other stuff with lots of texture So you can always do a mix and print the large parts on PLA and the face or parts with more texture with resin, it will save you tons of time and money in the long run.
Watched several of your videos and thanks they are great. I had a question though. I have carpal tunnel and have a hard time sanding for long periods. I have been looking into using resin to lessen the amount i need to sand but do you have any tips on reducing sanding or making it a bit easier. Mainly its about having to grip for long periods of time.
I remember watching that a short time in a box with nail varnish remover fumes does this easily without the need for sanding
That looks really good ❤. Standing and bit much but it still came out awesome.
ever tried smoothing prints with a soldering iron i have been doing it with amazing results even use it to fill in gaps melting plastc back into place and you now get irons with differnet shaped top so form in detail of prints
I subscribed immediately after seeing that mustache good work my guy good work
Your patience got rewarded with the quality look of the finished product. Well done! However, what is the point of printing the object in their intended colors if they will be sanded down for clean-up and then repainted?
Great video, quick tip if you use a dry box with a heater it will help reduce the amount of sanding.
awesome job.. . makes me want to get a resin printer...
Yo this is so cool. Cant wait to see how you paint it
Amazing video friend, thank you. Just got our ender 3, and this is going to be our first full print once things are all setup. Very inspiring !!
really nice video. It is nice to see the whole and long process. Often this is just mentioned as doing a lot of sanding and priming, but I better understand the efford after watching this.
You got yourself a new subscriber :)
This is a great step by step demonstration. My only suggestion is that on a really roughly printed area it might be worth double-checking the original model. I think you filled and sanded away the thin bottom edge of the cap.
Don't listen to the haters. Not everybody has a resin printer. I rarely even use mine because I don't have dedicated space to set up a stinky chem lab. Besides, at this scale I'd say the PLA print was cheaper and considerably more sturdy. There's nothing wrong with putting in the work to make it look nice.
Thanks so much for the comment. I did check the model there wasn’t much of an edge to it. I tried to make it more defined.
As for the haters. Yeah… this is a video on pla and good finishes. There are way more people with fdm and not resin printer for so many reasons like they have little kids in the house or afraid of the safety issues. If found the people that switch to resin rarely go back to fdm. But this video isn’t for them which doesn’t hurt my feelings when most people just say use resin without thinking of reasons people don’t use it.
Oh well the world we live In. I appreciate your comment. Thanks again!
Ignore the haters, I think most of them lack the patience to do what you've done.
I was going to ask if you'd considered using acetone? If you brush it over PLA models, it will smooth out a lot of the layer lines. Should save a lot of time.
@@stewburt5089 thanks!
So acetone works on abs prints but not pla at least the times I’ve tried it. It might depending on the brand or type if you have gotten it to work. The one thing I should of said in the video is this is for people that don’t have or can’t have resin printers. Most of the comments are just telling me to print in resin and that wasn’t the point of this… oh well.
I'll start off by saying, I enjoyed this video. I'm only just getting into 3D printing, so still researching and I only found out about resin printers today and, like I'm sure it is with most people, I thought it was magic, especially compared to PLA printing! So it got me thinking "do people stick with the lines of PLA printing, or do they work on making it look better" and I came across your video and it answered my question, yes you can work on it to make it look better.... But the amount of time it takes makes me think people probably don't lol.
I still have some unanswered questions though, do people usually not paint their 3D printings? I wonder this because there's so many different colors of filament, but it'd look so much better painted right? Oh and also does the quality of the printer make the lines less obvious? Or is it just a thing that'll always happen with that type of printing.
I never would have even considered thinning down plastic wood into a slurry. Thanks!
Oh yeah! It’s one of my secrets. Glad I could share.
So the secret to smoothing out fdm layer lines is....sanding them away! Wow. I'm blown away! This changes everything!....Jeez!
So some people are just getting into 3d printing and don't know how to smooth their prints! Wow, I can't believe you didn't know this. It changes my whole attitude about you. Idiot
@cecilepuckhaber1067 are some people using their hands for the first time? Sanding is not a new concept and is practically used on most metals and woods you see when you walk around, this is like learning your drainage leads to the city sewer, you should already know this you dunce.
I brush a lose mixture of wall plaster filler over the print then sand. Wall plaster filler fills all the layer lines and sands away in seconds.
That’s cool I’ll have to give that a try I bet it works great.
Have you ever tried a spritz of acetone from a spray bottle. It works pretty well depending on material
Great job. Instead of pink putty it would have been equal to use the resin 3D Finish? Do you agree?
use snug settings as support and you will solve the issue of sticking support parts
Like a lot of people, I'm choosing whether print accuracy or print aesthetics takes priority. On parts that have a high mechanical tolerance, that generally means that the support areas are going to be what everyone sees and and may need considerable clean up. For tight spaces consider looking into mini diamond files. That helps a bit but still not a perfect solution. I really want to give sandblasting a try but don't really have the space for one. Resin printing is not suitable for mechanical function in most cases. It's far too brittle. I've researched buying an SLS printer but a small format machine that would fit into a small residential workspace is still near $30k. Maybe someday.
W000t been waiting for this!😊
Awesome hope it helps you mark.
Wow this was a great video, I just had to subscribe. And a thumbs up as well. I am really new to this hobby of 3D printing so any tid bit of knowledge shared is greatly appreciated. Thank you so much and great stache !
Awesome, thank you!
Ive been waiting for this
Curious what a buffing pad for dremel would do for like a final once over after the high grit sandpaper? Curious if it would even do anything at all.
Such Beautiful Work ! ❤
Thank you so much!
i just use thicker (not to thick but not water like) primer based on acetone without sanding
then sand it , its waaaay easier because you already have filled layers just need to make it smooth and then aply thin primer
10times faster than any other method
You can use food filler thinned with water and use an old brush to make the layer lines invisible.
Looks cool. It’s a big help. Thanks.
i learned a lot from this video thank you so much. btw the watch is out of battery or broken, I couldn't keep from noticing the leg not moving much.
How many hours of post print work for the final finished painted product? Just curious what the reality is on how long it takes after the printing is done, to get this kind of result?
Just some advice for those who want to start sanding their projects, you may want to increase your number of permitters if you have a rough or bigger part that will require more sanding. It is not normally necessary but if you have a part that requires a lot of sanding, you can wear all the way through if you are not careful (assuming you are running default print settings with 2 shells). I think most people can get by by focusing on the primer (if youre sanding for aesthetics- most of my sanding is for dimensional accuracy so take this with a grain of salt) but you might want to give yourself some buffer on your first print or two.
I was wondering about that. I had a part I printed and only sanding a small amount I went through the wall enough to weaken the part and broke it. With sanding 80 grit, I would expect that the walls have to be much thicker than most normal parts. I don't get the point of 3d printing things though if you're going to have to spend hours sanding and finishing. Seems like it just completely defeats the point of 3d printing.
The Mini Plier Set link in your video description points to a concrete and brick drills set.
are these steps the same regardless of type of plastic? Do you treat PLA different than PETG or other types?
What a work of art! 👏👏👏😍😍😍
Thank you so much 😀
love your mustashe mate
Smooth PLA, great video. But seriously, the Pencil Handlebar Mustache is blinding....had to cover my eyes after 1 sec :-)
It seems you prime all the respective mortise and tenon faces for each piece and seem to avoid those areas when painting (and sometimes use silly putty for holes). It seems to me that plastic to plastic gluing would be better than paint-glue-paint. Or doesn't that matter?
Coming from other finishing FDM prints videos, they diulute bondo with acetone and uses it as a filler primer, but its thicker. Maybe the plastic wood and water could be shoot with an airbrush in order to keep the thickness to a minimum and speed a bit the process ?! Just an idea.
Also, how long would you say it takes to sand and prep ready for paint a model this size ?
That’s an interesting idea to try to spray it. The whole process of sanding and priming took about 5 hours. That includes all the dry times I had. Which could of been half of the actual time.
Really nice infomercial 🎉
As someone that also have a resin printer, I just put thin layer of resin over the PLA model, cure it, rinse and repeat until most of the layer lines are gone.
just noticed you sprayed that little bug on the left. 36:09
curious bug got sprayed, lol
Are there any good products to fill in gaps on functional parts that will handle a lot of shock and abuse? Have been looking for something that will truly fuse to the plastic and become part of it and not something that will just crack, chip, flake, scratch, etc...
you can also tape the sandpaper to a table and rub the part on it that way
Is there a difference use regular wood filler vs the plastic wood filler
I’m amazed that every video on YT I have watched regarding sanding, not one mentioned the most important step of sanding which is done post sanding, and that’s cleaning the dust and ensuring the surface is clean before adding any paint or putty.
would you get better results, or maybe faster, if you use acetone vapor to smooth it out? I don't know if it would make it easier to get to those places that you were having trouble reaching.
Hi I saw your video with my son and we loved it, he's a big Mario Fan, so ofc he wanted to print this model. But the link doesn't exist and more. I also used Yeggi to search for it but i couldn't find it. Would you mind pointing me in the right direction. Thanks in advance
Inspector Clouseau I presume? Just a tip, your Goatie is a bit wind swept to the left from where I sit but your right, it should be 100% semetrical, i.e, 50% left and 50% right, it helps if you could count the hair exactly to get a perfect look! LOL!
Got any tips videos for printing multiple models on the same plate? Getting excessive stringing between the models and they are at last 30mm apart. Maybe turn off coasting?
Retractions settings and dry your filaments.
@@MrLelopes Does just fine with one model. But multi is bad.
@@jesseburson stringing: filament is pouring out of the nozzle when you don’t want it to. Increasing the gap will only make it worse if you don’t solve the problem.
@@echo-hotel reduce flow?
Looks good. I'm just wondering why you printed it 3 different colors.
I love the cup
Ha ha. Yeah that was a gift from my wife. 😅
tk for the info sooooo helpful, Q: how long toke to sand the pice full ?
Longer than it's worth
did you try with 3d pen to fill and smoth the surface ?
Thanks for the tips. How many perimeters do you use when slicing a model you expect to process this way?
I slice it normally I typically do this process on certain models especially if the supported areas aren’t as clean as I need them to be. Sometimes I might just do a light sanding and primer with no putty. I have a Cura series where I go over the settings I check for every print.
@@ItsMeaDMaDe Thanks, I'll check that out
switch to UV putty, it dries in like 10~30 sec with UV light. u can get those thin sanding sponges instead of the big blocks, those work better for rounded surface. tho the grids ar higher, i think they ar around 400 800 1000/1200. You can also get scriber for modeling to carve those hard lines so you can ink later.
Sanding is definitely the most common that I still use, thanks for the techniques and tools!
Im aware of other methods like flex/hard resin dipping, latex dipping, XTC epoxy, Acetone fume polishing (this one's interesting), Chinese ultra fast PLA polisher (very interesting unknown material), oven baking (risky), and a few others
Sanding is key to getting that resin finish! Remember to use primer/filler for easier sanding process. 💪🎨
Looking amazing. Though if you have in mind a larger production, is this process viable? Or resin is the way to go?
very good bro,thanks
I got a battery powered Hyper tough "dremel" 8 volt version with variable speed...Single best thing I ever got for3D printing and was only 25 bucks. Actually very well built too! Ordered a bunch of various bit of amazon and I'm set. I HIGHLY recommend that thing! Awesome video too BTW...I ordered a set of those sponges too now.
Im now a new sub also...Thank you