7000W LOL. The so called power supply polarity changed between 8.47 and 8.58 and back again during the "demo". Capton tape does nothing as the transistors are screwed directly to the heatsink. Capton tape around the battery casing. My suspicion is there is a bluetooth module, small amp and battery inside the larger battery housing. the audio is fed virtually direct to the speakers via those heavy copper wires. The FET's do nothing. Love these vids. So much fun working out how it doesn't work.
Just a few concerns: First off, even though you used Kapton tape to insulate the low side transistors, the transistor drains are still connected to the heat sink, via the screw heads and threads. Second, both the input and output capacitors are reverse polarized. (both hooked up backward) Third, I don't see any pull up current to turn on the high side MOSFET's. The 270 Ohm resistor connected to the base of the D718 transistor is going to pull the gates of the high side MOSFET's down hard, regardless of input signal. The collector of the D718, will just pull the low side transistor gates to ground, turning them off as well. The emitter-base junction voltage drop is only ~.6 volts. It's just like a diode, with the cathode connected to ground, the anode connected to the 270 Ohm resistor. These are enhancement mode N-channel MOSFET's, so, to fully turn on the high side transistors, you need some kind of bootstrap circuit, to drive the gates at least 5 volts(a bootstrap circuit would give you 6 volts, if you are using a 12 volt battery) above the positive rail. I'm not seeing any kind of auxiliary supply, or, capacitors to shuttle the voltage from the output to the high side gates, to turn on those high side transistors.
i agree, also if he saying that ha having 7000Watts, and he he having one 1ohm speaker and one 2ohm speaker, he having 0.67ohm load. so if we calculate performance with ohm law, we would need: 69V and 103A on output (0.67ohm load.) 84V and 84A on output (1 ohm load.) 119V and 59A on output (2 ohm load.) Ofcourse we would get a little bit of resistance on the wires and components, so it would need a little bit more voltage. The whole amplifier doesn't make any sense. He having 12V input from battery, 1-2 Mosfet would be enough. if its a class A amplifier, the efficiency is arround 25% and the output voltage is 3V. on 0.67Ohm load, it is 13Watts. if its a class AB amplifier (unlikely), the efficiency is arround 50% and the output voltage is 6V. on 0.67Ohm load, it is 53Watts. if we having 90% efficiency which is imposible, only class D amplifiers can do that efficiency, it is 10.8V. on 0.67Ohm load, it is 174Watts. I think its a class A amplifier, The speakers dont have a loot of move, and these speakers are only 200 and 300Watts. The 2000 and 3000Watt car audio subwoofers are brutal, their weight are up to 20kg each, box not included.
This is low-fi. You need a high pressure vacuum tube push-push stage to drive your output stage. Think bipolar speakers, Mirage, Eclipse BP etc. Also, no transistors from broken ebikes and personal massage units Get some lateral FETs, Black Gates, Serpentis Oleum for smooth moving coil coupling. Just use a normal MMC thats tuned to the exact eigen takt of your room or house. This way its self exited and this provides very high ritalin effect in the standing WAveguide for Negative Koeffisient Erroneous Refractivity. If mmWave = active, goto "RattleLube". What cable did you use to transfer music or power? This must be audiophile quality or bit-perfect is no longer 1s and 0s, but maybe 0.98s and 0.3s. Its common knowledge that a computer must have 0 and 1 for binary refinement state. Integers and floating point is different, and the difference is called delta. For temp is deltaT and for bits in binary code its delta-integerale. This is the push-push with no compression loss. Force instead of lossy compression. Übermacht immer gewinnt. The most important factor is the wifi and the ethernet its connected to. Only 10/100baseT with solid aggregate state and Alligator Arresters. NO UPS. Uninterruptable PSU needs to be 50% interruptible to allow proper function of interrupt requests (IRQ) in the asynchronous audio transmission. Rifa, ROE, Elna etc does not work in PSU. Only reverse biased tantalum stacks. Hundreds of uF with reversed bias stacked tantalums not only sounds great, but all those orange caps soldered nicely together looks awesome. Better than High-End is Sky-End.
Kelebihan MOSFET mampu menghasilkan power daya Watt yg besar,seperti mana banyak kita lihat pada power amplifier kereta dengan Suply 12 vol mampu mengeluarkan bunyi yg menggerunkan .. mungkin jadi kajian dan sebagai inspirasi kita semua untuk mencoba sendiri di rumah .. selamat mencoba dan semoga sukses 🙏🙏🙏
A lo mucho 5w, todos los transistores en paralelo jajaja, no tendrás potencia con esa configuración, si fueran 7000w el altavoz se estaría moviendo con más fuerza y se ve que apenas apenas le da para mover sos altavoces
E un incluso dándole más voltaje tampoco dara más potencia por la confirmación de transistores que uso ya que usar transistores en paralelo provoca la disminución de la potencia en lugar de elevar la
E Ainda Tem Um Capacitor Eltrolitico de 16v 1800uf Na Saída Positiva Do Alto Falante , Se Esse Amplificador Tivesse Bastante Potência o Capacitor Não Suportaria a Alta Potência
wait a moment! why you use this yellow tape? as an isolator? really? do not think so, the Drains go to touch the heatsink anyway! just because the screws have no isolation and connect both surfaces! nice try! hehehe and almost forget it...finally you decided where to connect the battery red cable!
Did you by chance notice, both capacitors connected backward? or, the fact, that there is no pull up to bias the high side MOSFET's? This just can't work as shown.
Muy creativo pero le pregunto cual es la corriente adecuada para el funcionamiento correcto del mismo gracias si no eres egoista epero tu repuesta felicitaciobes
2к и 3к динамики нельзя запитать от 12v акума бо не хватит мощности им как минимум нужно 220v плюс наушники так нельзя подключить не будет работать и да эти динамики один на 200w другой 150w это примерно
@@specialistka1 Я с тобой согласен . Там где конечный каскад усилителя там надо ставить резистор а не конденсатор это позволит раскатать еще два каскада на один самбуффер
good job, but if you could put the loudspeaker in the box, I would like to hear the bass because this is how you can only hear the music is going and the bass is 0, it will be completely different in the boxes
You can put thousands of transistor but if you didn't increase the dc input you can't go anywhere. I'm just learning but watts or ohm means or is almost equivalent to input voltage
Kkkkk,48 MOSFETs R$> cada um custa 20 a 30 reais se tá louco. , Fica mais caro do que comprar um amplificador completo. Kkkkk , só tem louco nesse TH-cam. É cada uma
There are so much problems, for mosfets the tape is okay but the screws dont have voltage protective plastic on it, its gonna make instant short circuit you not gonna run an amplifier on 12volts while there are 48transistors, waste of material and time.
Never ever connect left and right channel straight together. Frequencies could cancel each other and in worst case, you could blow the output stage of youre soind source
Si no colocó los aislantes en los tornillos, creo que nos está tomando de bobos, porque al colocarle la alimentacion se juntan el negativo con el positivo y todo se arde. No creo que sirva de algo esto.
@@jeanpierre3193 yeah it might be. also its no more than 13Watts at total power, also the Drain of the mosfets and the Bjt transistor collector pads are shorted with the screws, he did capton tape it, but still the screws lets the current go. The creator just under 2digit number of IQ, and his Amplifier idea dont make any sense at all. This is sad.
Well ok that's one part of an amp now you do no that all amp work off ac so now you need to build the power supply for what you have there and then you can wake it up
7000 watts woth 12V ? , It means that the cables Can support like 550 Amps of current , its too huge for your battery. At the maximum the current is around 20Amps ... 240W ...LOL
да блин,он же включил на полную мощность.и где 7000вт?что то дины больно хлипкие для такой мощи,,,,да и где видано однополярка выдаст вам хоть 1000вт в такой то схеме?🤔
Aunque lo alimente con más voltaje y ampe no dará más potencia, son de estos amplificadores clase A qué a lo mucho te da 5w todo esto, solo conecta transistores en paralelo y eso no te aumenta la potencia solo aumenta la resistencia del voltaje del transistor, el video es falso en pocas palabras, esos 7000w son a los mucho 5/10w
12v in 7000watt 🤣😂🤣 much more super³ crazy..all must be build this amp... add mosfet 99999999x time cant up your amp more watt..must be same with supply...
you are just dumb if you do that, dont do it. It's not recomended. He made nonsense, and he did waste 48mosfets, for short circuit and one Bipolar Junction Transistor.
*DIY Powerful Ultra Bass Amplifier TDA7388 BTL 12 Transistor D718 , No IC , Simple Circuit **th-cam.com/video/-W1c80Cuo1c/w-d-xo.html*
7000W LOL. The so called power supply polarity changed between 8.47 and 8.58 and back again during the "demo". Capton tape does nothing as the transistors are screwed directly to the heatsink. Capton tape around the battery casing. My suspicion is there is a bluetooth module, small amp and battery inside the larger battery housing. the audio is fed virtually direct to the speakers via those heavy copper wires. The FET's do nothing. Love these vids. So much fun working out how it doesn't work.
Just a few concerns: First off, even though you used Kapton tape to insulate the low side transistors, the transistor drains are still connected to the heat sink, via the screw heads and threads. Second, both the input and output capacitors are reverse polarized. (both hooked up backward) Third, I don't see any pull up current to turn on the high side MOSFET's. The 270 Ohm resistor connected to the base of the D718 transistor is going to pull the gates of the high side MOSFET's down hard, regardless of input signal. The collector of the D718, will just pull the low side transistor gates to ground, turning them off as well. The emitter-base junction voltage drop is only ~.6 volts. It's just like a diode, with the cathode connected to ground, the anode connected to the 270 Ohm resistor.
These are enhancement mode N-channel MOSFET's, so, to fully turn on the high side transistors, you need some kind of bootstrap circuit, to drive the gates at least 5 volts(a bootstrap circuit would give you 6 volts, if you are using a 12 volt battery) above the positive rail. I'm not seeing any kind of auxiliary supply, or, capacitors to shuttle the voltage from the output to the high side gates, to turn on those high side transistors.
I agree ☝️
i agree, also if he saying that ha having 7000Watts, and he he having one 1ohm speaker and one 2ohm speaker, he having 0.67ohm load. so if we calculate performance with ohm law, we would need:
69V and 103A on output (0.67ohm load.)
84V and 84A on output (1 ohm load.)
119V and 59A on output (2 ohm load.)
Ofcourse we would get a little bit of resistance on the wires and components, so it would need a little bit more voltage.
The whole amplifier doesn't make any sense.
He having 12V input from battery, 1-2 Mosfet would be enough.
if its a class A amplifier, the efficiency is arround 25% and the output voltage is 3V. on 0.67Ohm load, it is 13Watts.
if its a class AB amplifier (unlikely), the efficiency is arround 50% and the output voltage is 6V. on 0.67Ohm load, it is 53Watts.
if we having 90% efficiency which is imposible, only class D amplifiers can do that efficiency, it is 10.8V. on 0.67Ohm load, it is 174Watts.
I think its a class A amplifier, The speakers dont have a loot of move, and these speakers are only 200 and 300Watts.
The 2000 and 3000Watt car audio subwoofers are brutal, their weight are up to 20kg each, box not included.
I agree with you
And the speaker power ratings are also on the magic side.
@@wurgervomlichtenmoor5073 yeah
Пойду на своём сабе напишу 2000ват, и тоже видео сниму xD
не забудь тоже короб выкинуть и динамик должен строго играть попсу , питаясь от 12 вольт
12V 12Ah battery?? max 10watt amplifier
Le falta Power
12v can go 10 to 15watt i think...
@@ourchannel8215with class d amplifier lol
This is low-fi. You need a high pressure vacuum tube push-push stage to drive your output stage. Think bipolar speakers, Mirage, Eclipse BP etc. Also, no transistors from broken ebikes and personal massage units Get some lateral FETs, Black Gates, Serpentis Oleum for smooth moving coil coupling. Just use a normal MMC thats tuned to the exact eigen takt of your room or house. This way its self exited and this provides very high ritalin effect in the standing WAveguide for Negative Koeffisient Erroneous Refractivity. If mmWave = active, goto "RattleLube".
What cable did you use to transfer music or power?
This must be audiophile quality or bit-perfect is no longer 1s and 0s, but maybe 0.98s and 0.3s. Its common knowledge that a computer must have 0 and 1 for binary refinement state. Integers and floating point is different, and the difference is called delta. For temp is deltaT and for bits in binary code its delta-integerale. This is the push-push with no compression loss. Force instead of lossy compression. Übermacht immer gewinnt.
The most important factor is the wifi and the ethernet its connected to. Only 10/100baseT with solid aggregate state and Alligator Arresters. NO UPS. Uninterruptable PSU needs to be 50% interruptible to allow proper function of interrupt requests (IRQ) in the asynchronous audio transmission. Rifa, ROE, Elna etc does not work in PSU. Only reverse biased tantalum stacks.
Hundreds of uF with reversed bias stacked tantalums not only sounds great, but all those orange caps soldered nicely together looks awesome. Better than High-End is Sky-End.
Kelebihan MOSFET mampu menghasilkan power daya Watt yg besar,seperti mana banyak kita lihat pada power amplifier kereta dengan Suply 12 vol mampu mengeluarkan bunyi yg menggerunkan .. mungkin jadi kajian dan sebagai inspirasi kita semua untuk mencoba sendiri di rumah .. selamat mencoba dan semoga sukses 🙏🙏🙏
harus ada penaik voltage supplynya ...jika guna 12v doang..mau guna 10 tliliun mosfet pun sama aja watbya tetap kecil
A lo mucho 5w, todos los transistores en paralelo jajaja, no tendrás potencia con esa configuración, si fueran 7000w el altavoz se estaría moviendo con más fuerza y se ve que apenas apenas le da para mover sos altavoces
¡si, es verdad! alimentado por una batería de 12 voltios, no mucha energía
E un incluso dándole más voltaje tampoco dara más potencia por la confirmación de transistores que uso ya que usar transistores en paralelo provoca la disminución de la potencia en lugar de elevar la
Bence izolasyon hatalı olmuş. O alüminyum soğutucuya bütün mosfetlerin orta uçları temas etti.
E Ainda Tem Um Capacitor Eltrolitico de 16v 1800uf Na Saída Positiva Do Alto Falante , Se Esse Amplificador Tivesse Bastante Potência o Capacitor Não Suportaria a Alta Potência
watching and sending support again nice sharing
superb
I have to try it
wait a moment! why you use this yellow tape? as an isolator? really? do not think so, the Drains go to touch the heatsink anyway! just because the screws have no isolation and connect both surfaces! nice try! hehehe and almost forget it...finally you decided where to connect the battery red cable!
Did you by chance notice, both capacitors connected backward? or, the fact, that there is no pull up to bias the high side MOSFET's? This just can't work as shown.
@@vincentrobinette1507 yea, its very, very sad. The whole amplifier dont make any sense.
Muy creativo pero le pregunto cual es la corriente adecuada para el funcionamiento correcto del mismo gracias si no eres egoista epero tu repuesta felicitaciobes
Woww 99999 bastt🤯🤯🤯mega bastt
2к и 3к динамики нельзя запитать от 12v акума бо не хватит мощности им как минимум нужно 220v плюс наушники так нельзя подключить не будет работать и да эти динамики один на 200w другой 150w это примерно
He is crazy try to fool everyone
Развод чистой воды, и аккум один и тот же, на Верника там встроенный усь и показывает разные схемы, просто побор видосиков.
Все это ерунда, по факту усилитель на одном транзисторе D718, мощности здесь не больше 10 Вт
Evet bence de öyle 👍
Ты не прав там используется много транзисторов и звук очень классный
Согласен , подключено паралельно . Усиления быть не должно совсем
зачем было городить полведра транзисторов, каскад один, питание 12 вольт, и да мощности он развивает ватт 10 а то и меньше
@@specialistka1 Я с тобой согласен . Там где конечный каскад усилителя там надо ставить резистор а не конденсатор это позволит раскатать еще два каскада на один самбуффер
Muy bueno! pero tendría que ponerlo al Woofer en una caja para poder Apreciarse bien el sonido
good job, but if you could put the loudspeaker in the box, I would like to hear the bass because this is how you can only hear the music is going and the bass is 0, it will be completely different in the boxes
You can put thousands of transistor but if you didn't increase the dc input you can't go anywhere. I'm just learning but watts or ohm means or is almost equivalent to input voltage
Very good...
Hay quá anh đức black
Đây là kênh thứ 2 của anh thợ điện hả bạn
Wow 🤩🤩😍😍🤩🤩🤩
Nice bro👍👍👍👍👍👍👍👍🌹
Это же какая входная ёмкость затвора этой гирлянды
Mantap bro ok ni 👍👍👍👍❤️
Good video
good job sir, watching sending my support
Qual a corrente adequada pra se colocar nesse amplificador? Em corrente continua. 🤝 Ceará- Brasil
Ser gd am ask kulang kung magkanu mag pa assemble nyan muspit ang gamit
Good
what is the limit power (A.C) for it i want ti use volte instead of battery
Puoi anche montare 8000 transistor, ma se li alimenti a 12 volt, ottereai al masdimo 10 watt RMS.
Wow keren.😀
hey you try build same this circuit..but u just used 1 pair mosfet..i think the sound its same...
Огонь, изоляция каптоном, а винты без проставок. Фейк, кто то ведётся.
Correct
Dude, without mixing amplifier, tune's like normal range speaker
43 mosfet do you think all are working?
Kkkkk,48 MOSFETs R$> cada um custa 20 a 30 reais se tá louco. , Fica mais caro do que comprar um amplificador completo. Kkkkk , só tem louco nesse TH-cam. É cada uma
Recicla
Aq é Brasil amigo e não é um país para amadores.
जय माता दी
Bruh that’s a huge waste of mosfets, I would use those mosfets for an inverse circuit and it can probably transform huge amounts of energy
Nice
mạch loa công suất 👍👍👏🏳️🌈
There are so much problems,
for mosfets the tape is okay but the screws dont have voltage protective plastic on it, its gonna make instant short circuit
you not gonna run an amplifier on 12volts while there are 48transistors, waste of material and time.
Gücü çok az olmuş? Hoparlör diyaframı neredeyse hiç oynamıyor. Performansı düşük gibi.
Изолирующюю прокладку поставил, а винты не изолировал....
Nice bro👍👍👍👍👍
Alektronik firmaları hiçbir şey bilmiyorlar bundan akıl alsınlar 😝😝😝😝
Never ever connect left and right channel straight together. Frequencies could cancel each other and in worst case, you could blow the output stage of youre soind source
Лайк за видео, ты молодец 👍
Nice 👍👍👍
Battery is very suspicious 😕
muito bom parabéns, falando do Brasil goias caldas novas.
Heyy bro
Can you make a easy one please
Bro video m thoda Bola Karo
Components ki jankaeri Diya karo
How many watts will this circuit give
50w amp+10a acu=50w sound
1000w amp+10a acu =50 w sound
китайские ватты = умножать на 10 000 а русские ватты делить на 100
12V @4ohm =3A the maximum output power il 36W
Wow
Si no colocó los aislantes en los tornillos, creo que nos está tomando de bobos, porque al colocarle la alimentacion se juntan el negativo con el positivo y todo se arde. No creo que sirva de algo esto.
Los que aislo necesita aisladores de plastico en los torniosso los negativos ya que reciben corriente negativa
Good 👍
what is the song name which you play in speaker at last
Wow 48 power mosfets
Q, Why WTF 4???
where is the thermal paste
Genial muito bom (10)
Purchase links please
Bisa di pesan ngak mosfet 75n75 nya mas
❤❤❤
U wil not assemble HPF & LPF bord with this amplifer 👍
Saludos hermano que tipos usas para este circuito
Xem đầu
👏👏👏👏👏👍🏻👍🏻
I don't think this is more than 400watts RMS
This circuit is totaly bullshit!,more than 8 Mos-Fet in parralel is NOT possible (gate-source capacitance too high!)
@@jeanpierre3193 yeah it might be. also its no more than 13Watts at total power, also the Drain of the mosfets and the Bjt transistor collector pads are shorted with the screws, he did capton tape it, but still the screws lets the current go. The creator just under 2digit number of IQ, and his Amplifier idea dont make any sense at all. This is sad.
Well ok that's one part of an amp now you do no that all amp work off ac so now you need to build the power supply for what you have there and then you can wake it up
7000 watts woth 12V ? , It means that the cables Can support like 550 Amps of current , its too huge for your battery. At the maximum the current is around 20Amps ... 240W ...LOL
its just 13W, remember dude, the amplifier efficiency is only 25% at max power.
👍👍
No use of tape screw will short circuit with heat sink
He put insulators under the transistors but forgot to separate the screw 🤣😂🤣😂
Круто
Hâha người Việt
Less voltage brother
EXTREME
A dùng thiếc j vậy
🎉🎉🎉
Put your speakers in enclosures
Trên kênh anh thợ điện ko thấy phát
да блин,он же включил на полную мощность.и где 7000вт?что то дины больно хлипкие для такой мощи,,,,да и где видано однополярка выдаст вам хоть 1000вт в такой то схеме?🤔
se puede conectar corneas de 8 ohm a ese tipo de planta casera
como se hace uno haci para saber armar uno
Que mal q use una batería eso hace q no desarrolle suficiente potencia
Aunque lo alimente con más voltaje y ampe no dará más potencia, son de estos amplificadores clase A qué a lo mucho te da 5w todo esto, solo conecta transistores en paralelo y eso no te aumenta la potencia solo aumenta la resistencia del voltaje del transistor, el video es falso en pocas palabras, esos 7000w son a los mucho 5/10w
Sao giống anh thợ điện ấy nhờ
Какой смысл подключать низкочастотные динамики в полную полосу?
i bet the woofer isn't even near 3kw and that isn't even impresive cone movent
12v in 7000watt 🤣😂🤣 much more super³ crazy..all must be build this amp...
add mosfet 99999999x time cant up your amp more watt..must be same with supply...
No mueve nada los conos.. le falta mínimo 70 voltios
hola quetal me puedes Aser uno Soy de Olimpo
El vídeo es falso .______.
Ser hou much assemble
Visezi cam multe prietene 😆😆😆
Hi, I work for BBTV and would love to connect with a business opportunity. Please let me know!
you are just dumb if you do that, dont do it. It's not recomended. He made nonsense, and he did waste 48mosfets, for short circuit and one Bipolar Junction Transistor.
Nagyon torzíthat.
Из какой страны ты