How To Apply WaterSlide Decals

Mark Kirk Show Us How To Apply WaterSlide Decals
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▶For any business inquiries please contact us at: [e-mail]
▶Check Out The BEST Gunpla News: • Gunpla News: GM Guard,...
▶MG Reviews: / watch
v=xv5rRVC5CD8&list=PLGGZ5BSUuePI7AvN2Y0_FO8-gIlv8ywCA
▶HG Reviews: • HG 1/144 AGE-3 Normal ...
▶RG Reviews: • RG 1/144 RX-78-2 Gunda...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▶Get Your Official Merchs: teespring.com/stores/gunpla-n...
▶Join Us On Facebook: / gunplanetwork
▶Check Out our Instagram: / gunplanetwork
▶For All The Latest News:
www.gunplanetwork.com
#gunpla #plamo #gundam
Music By Kijugo
• golden wind (Jojo but ...

[@markkirk7305]

1. Cut out the decal and dip it in warm water for 5 seconds
2. Take it out and sit it on a paper towel
3. Get some setter and put a drop where you want the decal
4. Slide the decal off the paper and position over the setter
5. Use a cotton bud and roll it over the surface to remove the excess setter
6. Let dry for 5-10 Mins and then brush a small amount of softer over the decal
7. Don’t touch it even if the decal gets wrinkled
8. Let it dry naturally

[@BigGun1911]

I’ve never done anything like this but em going to try it out with the Marvel Legends Target exclusive Thor Ragnarok. His eyes are red and want to paint them white and add water decal eyes.

[@nopparat6388]

Excus me i dont have setter (because the money is gone)

[@markkirk7305]

@z.1306 it helps if it is stuck to the paper warm gets it off

[@artyourself-qz9pv]

Thank you

[@No1PepsiFansProductions]

But does the decal et sealed to the model to the point where it looks like it's part of the plastic

[@tonygant2448]

This vid was a lot more helpful than the instructions that came with my Gundam. Thanks!
Short and straight to the point with some chill music.

[@taylonsanchez8840]

Is no one gunna talk about how criminal this beat is? Straight iller than hamburger filler.

[@djangofett4879]

Cool, These are the exact two solutions that i was wondering if i can use together. thank you!

[@mikailvaynstok8083]

It's a Gundam!

[@Memeamyoto621]

I mean i wish I knew what the other 2 products used were .

[@markkirk7305]

WhIch ones man?
Mark fit by tamiya / or mr mark setter
Mr mark softer
Water

[@Hakken_bokke]

is it necessary to apply mark fit and mark softer?

[@EDGE369]

Is it better to remove top coat first before applying WSD? I already applied Matte Finish but I am planning on adding some decals on my kit

[@NeoSlashott]

so setter bonds while softer makes decals flushed?

[@awesomeguy7624]

Well the softer is meant to sorta melt it so it can better adhere to curves and go into pannel lines whilst bond is a glue to keep it there

[@markkirk7305]

Yeah pretty much man

[@Nanodayo08]

After the decal dries, is it scratch proof like the ones on barbie's eyes?🤔(I know it's not 100% scratch proof, but it's not easily removed either with one scratch😂)

[@Truck-kun_01]

What would you do if you don't have the setter

[@DarkTetsu]

You don’t need the setter. It’s only if you want to melt the decal around a curve or eat the clear portion of the water slide.

[@Truck-kun_01]

@@DarkTetsu it might've been a year too late, but your advice will always be appreciated. kind stranger

[@BigGun1911]

Do you have to seal it? New to this all btw

[@No1PepsiFansProductions]

Could I also use Mr mark setter

[@SwtAngelSakura]

Do you need to water for it to completely dry before applying the final seal?

[@DarkTetsu]

I would let it dry in order to seal properly. Water can’t evaporate through a top coat.

[@kimchipunch]

Is it better to topcoat before or after applying water slides?

[@GunplaNetwork]

After to seal them

[@markkirk7305]

If the kit isn’t something super shiny or special surface I use it before and after

[@ghostmonkeycustoms3766]

No top coat????

[@zawiahtengah5374]

it