Thank you for taking the time to make this video. I've never adjusted my valves myself on my DRZ. I've probably watched this video three or four times now and it's really making me anxious to want to try myself. Snow is melting fast and riding season is upon us in my area so I'm afraid if I don't get it right I'm going to lose ride time 🤣 seriously though, thank you!👊🏼
Great video, i'm down east in Nova Scotia I have a 2018 DRZ400S, I do a lot of riding has 31000 kms on it now, I'm getting a lot of deceleration pops when I let the throttle go but none in acceleration and It stalls every week or so once then takes a few min to start again but will run fine in between, starts up real easy, I am going to check the clearances and take the carb off and clean it, I use an NGK iridium spark plug and only use supreme fuel.
Thx a lot !! it is very well made . this video add so much confidance to only use the factory maintenence guide . It will help for changing to stage 1 HOT CAMS ;)
Hello. I done this job. I think it will be ok.I have a question. I read that I must verify that my cams are getting oil. I read that I must take out the bung beside the Tensioner. I did and have turned the engine over using the starter with the plug removed. Please tell me why no oil has come up so far. ( New oil and new filter). Thank you.
![[MV] A leap of faith...ความเชื่อใจครั้งสุดท้าย (From "Petrichor the series")](http://i.ytimg.com/vi/U1piZH2CNXA/mqdefault.jpg)
Thank you for taking the time to make this video. I've never adjusted my valves myself on my DRZ. I've probably watched this video three or four times now and it's really making me anxious to want to try myself. Snow is melting fast and riding season is upon us in my area so I'm afraid if I don't get it right I'm going to lose ride time 🤣 seriously though, thank you!👊🏼
Great video, i'm down east in Nova Scotia I have a 2018 DRZ400S, I do a lot of riding has 31000 kms on it now, I'm getting a lot of deceleration pops when I let the throttle go but none in acceleration and It stalls every week or so once then takes a few min to start again but will run fine in between, starts up real easy, I am going to check the clearances and take the carb off and clean it, I use an NGK iridium spark plug and only use supreme fuel.
Great video! Just did an install of stage 1 hotcams, however my tolerances were way too tight on the exhaust side, this is definitely going to help!
Thx a lot !! it is very well made . this video add so much confidance to only use the factory maintenence guide . It will help for changing to stage 1 HOT CAMS ;)
When you/he said «take note of the orientation before taking off the cams», he ment the lobes right?
There are markings on the cam gears so you get it back into the same spot.
Hello. I done this job. I think it will be ok.I have a question. I read that I must verify that my cams are getting oil. I read that I must take out the bung beside the Tensioner. I did and have turned the engine over using the starter with the plug removed. Please tell me why no oil has come up so far. ( New oil and new filter). Thank you.
Thank you for charing. just subscribed
Great video thx for sharing!
Easy and clear, THANKS!
Great vid mate cheers
Is there anything special to reset timing chain when you put it back in? Like tighten or loosen or you put it all back together and it’s fine?
You forgot to mention, WHAT YEAR IS YOUR BIKE AND HOW MANY MILES ON IT, GOOD LORD
First time doing this, I’ve got the line at TDC, but my cams are pointing in instead of out…any suggestions?
rotate till cam lobes are like in the video and check for the line in the sight hole, 4 stroke so you may be on the wrong stoke.
Hi,do you have to remove the spark plug to check the valves?
What year model is that
My cam covers refuse to come off, everything is loosen. Still trying to figure how to take it off for the past weeks
Did you get it?
I was hoping this bike did NOT have the bucket/shim style valves.
I feel that they are a better system and not quite daunting once you have done it a few times.
The DR 650 has rocker arms with screw adjusters.
You from Wisconsin?
nope, northren Alberta Canada
Is this the same engine as ltz 400? Bc mine won't start it pops out flames but no start
th-cam.com/video/38qb4gDS7J0/w-d-xo.html
BJ it looks the like the same engine however I can only see the one side. I would check the values and cams, could of slipped a tooth on the cam.
It looks so scary so much to do.
Ok ok ok thanks
starts at 4:40
Wow, never gotten motion sickness from a how to video before. very informative but the camera work literally missed the mark.
too shaky to watch. also, switch to decaf
Bucket and shims. No thanks
Nubar 1Timing number 2 battyr dhamech