Setting Float Height - Mikuni Carburetor - Yamaha Fj600
ฝัง
- เผยแพร่เมื่อ 6 ก.ค. 2013
- This video supplements the the instructions called "setting the fuel levels" which can be found at xj4ever.com. It shows some of the details needed to set the float levels on a set of Mikuni BS-32 Carburetors from a 1985 Yamaha FJ600. This is a common procedure and many of the same steps can be used to set the float levels on many different types of carburetors.
Due to factors beyond the control of mreinsmith, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. mreinsmith assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. mreinsmith recommends safe practices when working with power tools, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of mreinsmith, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not mreinsmith. - ยานยนต์และพาหนะ
thanks for posting. it's rare to find such a straightforward video. i wanted to check to see if i could use a regular clear fuel tube or if it had to be a specific diameter. thanks.
instaBlaster...
good vid. the float heights should only be used as a guide as the tang on the float which makes contact with the needle valve might be slightly bent different thus making the float height the same but the fuel level different. always use the clear tube method of checking actual fuel height in the bowls with the bike level and warmed up then shut off or as in the vid bench sync . the manual for the bike usually states where the fuel should be in relation to the bowl cover .
i speak from personal experience with my fzr 400 and weeks of messing with the carbs ;-)
cheers for posting its the only way we learn ;-)
Super video... I ll try your tehnics on my 1982 Xj 550.
Sebi Berceanu how did it work for you? Working on a xj550 right now
Do you really have to measure with the carbs on its side? I thought it was OK for the bowls to "rest" on the inner pin (under the weight of the bowls).
very helpful thanks
What value in millimeters was put on the caliper when measuring the floats???
Jak sie nazywa to uzadzenie do ustawienia odleglosci
Was that on the gasket base or carb body?
Really easy instructions to follow, but such a shame that you don't give the course measurement of the float height as a datum to get people started. Having a course measurement to start with would give you a chance of getting one or two right and mean less removing the float bowls. Otherwise good though.
Good point, I still have the docs so let me find it, Thanks!
i cant figure how to get my carbs out of my FJ?
Does it not matter how long the house is?
Not for bench setting, just keep the source high enough to create some gravity pressure, you're only trying to fill the bowls.
Here we used the tank itself, since then I found a bottle that works well
Bench setting gets you close, if not right on, and it helps you get back to a baseline
Once you've done this and you think it needs to be improved, then move on to running adjustments
your level doesn't seem to be set properly. why's it level with edge/flats of carbs? dunno what your bikes level is but on my r1 it's 5.1mm above flat on carb.
Something tells me the mark your looking for in this case is different, but i honestly can't remember, the setting is in the instructions on xj4ever.com
Oh yeah, and maybe the note at 1:43 explains that too? It's been a while since I've done one
where did you get the adapter to connect hose to bowl?
I had a fitting from a vacuum pump kit I had
It looks like one that came with my "Mighty Vac" that I use for bleeding brakes.
I think that's correct! I didn't want to use brass so I scrounged from that pump kit - Good eye!!
When you guys were trying to get the air out of the fuel line, I was yelling at my phone saying “pull the end of the damn tubing up past the point of the bubble and it’ll vent itself out!” Hahahah. Over-analytical, over-thinking couple of guys, but you missed the obvious solution to such a simple solution
I am what I am! ;-)
@@mreinsmith it’s all good, i often overthink life in other aspects. Nice job on the rack that held up the carbs. I don’t have the patience or desire to spend the money on the parts needed, so I’ll just resort to ductaping them to a pole or something haha.
Hey, as long as you are getting the job done and having some fun, that's All that matters! Thanks for watching and commenting!
@@mreinsmith i agree, I was just being unnecessarily hard on you and an ass. I admire your forethought and execution and I leaned something which is great. Thank you and take care :)
Норм