My dang big bore ezgo txt shakes when first taking off and when stopping. Parking it slowly in the garage feels like the whole motor is gonna fall off lol. It also won’t go in reverse unless you turn the motor off, switch the lever to reverse, and then start it up again. Gonna mess around with it one of these days to see if I can figure it out
I have 2015 EZGO rxv. The clutch is working as it should but have a rattling noise from it when driving…Any idea besides drive it till it fails. Thank you for your time. Where is your shop located?
I just bought a 1999 ezgo 38v and when I press the gas it will go but then it starts hesitating. It will even sort of jerk sometimes. Do u have any idea what that could be?
It’s actually 48 volt and u don’t think I should check the vglide? Also the guy we bought it from installed a beast motor he called it. I think he said for more torque?
@@babyalivesandslime9731 no worries. Check your battery voltage while you’re driving it. Or hold the brake down as you hit the gas and check each battery under a load.
Question for you. 2008 Club Car DS. When I put it in gear, forward or reverse it takes a second or two for it to engage. Jurks when it does engage. Any ideas?
Is this for a fuel injected ezgo? I’ve got a 21 valor and it hesitates, then does nothing. If I push it and hit gas it will go. Took it to a place and they said too new to work on it. They said belt was jumping? It’s got a kwang Yang engine in it? Do you know anything about those?
If it’s int running. Meaning when you hit the gas sometimes and it does nothing then you hit a couple more times and it runs. Replace the computer. Don’t waste your time or money on nothing else but the computer. It’s called a starter/generator controller. It will fix your problem. I replace about 30 a year.
I have an 04 Club Car Gas golf cart. You push on the gas it runs but not fast enough to engage the clutch. Any idea what would prevent it from going full speed? Thank you.
@@HeyHeyHey97 No, it was being driven when it started doing it. It happened about 2 weeks ago and it cleared itself up. Now it just chugs and doesn't move.
My dang big bore ezgo txt shakes when first taking off and when stopping. Parking it slowly in the garage feels like the whole motor is gonna fall off lol. It also won’t go in reverse unless you turn the motor off, switch the lever to reverse, and then start it up again. Gonna mess around with it one of these days to see if I can figure it out
Sounds like your front clutch is stuck
@@HeyHeyHey97 nice vid btw 👍👍👍
I have 2015 EZGO rxv. The clutch is working as it should but have a rattling noise from it when driving…Any idea besides drive it till it fails. Thank you for your time. Where is your shop located?
If the rattling is from the clutch. There’s nothing you can do. Check the muffler also for a rattle!
Located in NMB sc
You were spot on…muffler bracket was loose noise gone. Thank you for the help and the videos!!
@@dhrr44 yes sir thanks for letting me know what you find out. Just hit that like button for me. And subscribe
I just bought a 1999 ezgo 38v and when I press the gas it will go but then it starts hesitating. It will even sort of jerk sometimes. Do u have any idea what that could be?
Check battery voltage. if battery voltage is good. Take your motor off and unstick the brushes
It’s actually 48 volt and u don’t think I should check the vglide? Also the guy we bought it from installed a beast motor he called it. I think he said for more torque?
Btw battery voltage is good. Thanks in advance and sorry for all comments.
@@babyalivesandslime9731 no worries. Check your battery voltage while you’re driving it. Or hold the brake down as you hit the gas and check each battery under a load.
Question for you. 2008 Club Car DS. When I put it in gear, forward or reverse it takes a second or two for it to engage. Jurks when it does engage. Any ideas?
Front clutch is probably sticking
Seal on my torque clutch is leaking. Can you make a video on how to change it?
You mean input shaft seal
What kind of grease do you use for installation?
I just use regular trailer bearing greass
Is this for a fuel injected ezgo? I’ve got a 21 valor and it hesitates, then does nothing. If I push it and hit gas it will go. Took it to a place and they said too new to work on it. They said belt was jumping? It’s got a kwang Yang engine in it? Do you know anything about those?
Kwang Yang. You mean Kawasaki engine. Or the small moped engine they use
Must be, but was wondering if it was the same as this?
If it’s the small moped engine. No it’s different than this. But if it’s the Kawasaki yea
But on the moped engines they are bad for the computer causing. Int running
If it’s int running. Meaning when you hit the gas sometimes and it does nothing then you hit a couple more times and it runs. Replace the computer. Don’t waste your time or money on nothing else but the computer. It’s called a starter/generator controller. It will fix your problem. I replace about 30 a year.
Are there any other options to get it off if I don't have an airgun
Take a hammer and a punch. Be careful not to bust
@@HeyHeyHey97 Awesome thanks man
Can I spray wd 40 in there without removing?
It won’t help
It won’t help most grease it.
I have an 04 Club Car Gas golf cart. You push on the gas it runs but not fast enough to engage the clutch. Any idea what would prevent it from going full speed? Thank you.
So it’s turning over just not cranking up?
@@HeyHeyHey97 Yes
Check fuel or spark
Check make sure throttle is opening. Has it been sitting for a while.
@@HeyHeyHey97 No, it was being driven when it started doing it. It happened about 2 weeks ago and it cleared itself up. Now it just chugs and doesn't move.
I have a battery question how do I contact you?
I don’t give my personal stuff out. you can ask question on here
Sir how can I contact you?! 😬
Don’t give my number out. Too much bs scams. Will respond back here
Thanks!
Thank you man. I appreciate the super thanks
Worst review I’ve ever seen, how did that solve the problem.
Lol. Because the clutch was sticking in a little bit. 🤔
My problem is a whole bunch of tall grass worked it's way into the end of the clutch. I got the clutch puller bolt, so hopefully I can get it out.
I would just pump grease in the end of the clutch