How to remove a drum from a top loader washing machine - step by step
ฝัง
- เผยแพร่เมื่อ 12 ม.ค. 2020
- How to remove a drum from a top loader washing machine
Panasonic EcoNavi
In this video i show how to remove the drum from a top loader. The pulsation was stuck and i also show how to remove the stuck pustular.
![CAMPปลิ้น | EP.79[1/2] แก๊งไทบ้านพาบุกเมืองบั้งไฟโก้ ยโสธรรรร!!!](http://i.ytimg.com/vi/Ldr3_fvTEXk/mqdefault.jpg)
Thank you for making this video because I wanted to open my washing machine and I never could . But now I can open it
I managed to get the pulsator and drum nut off. But the drum seems stuck to the gearbox shaft? Any tips on how to get the inner drum unstuck from the gearbox shaft?
Very educational and informative
Thank you appreciated.
Very very usefull thnk u verymuch sir😎
Very good video thank you
Very good video.
@ecologicaltime Thanks for the video, really very useful. I'm trying to clean my Samsung top loader washer. Was able to remove the pulsator however the top nut (it's 35mm for Samsung) is not coming out - using the impact drive with 35mm socket. So was trying to see if you removed it in counter-clcokwise direction or clockwise.
from memory it was usual rotation clockwise for tightening
instablaster.
Super tutorial sir
Thanks a lot.
I encountered nut was too tight to loose it may b it's stuck inside,so I wondering could use powerful impact drill to open it or not...will it caused broken?
Around 2:50 you openned the drum bolt.
I repaired my panasonic f60gs gear box so i had to open the drum so i can easily replace the gearbox. Now i've done everything and assembled the machine once again the PROBLEM is that, the nut of the drum is kept opening when i ever i put the machine on wash rinse or spin. The nut loosen itself. What is the solution to fix the nut.
I have tried my best hard to tighten the nut with a wrench.
Need help please guide
What do you used impact wrench type sir?
On the LG washer check your washer to see if you have a Hose Clamp or Glue on the inbound side of the discharge pump. If so, that is not a factory connection. There is not supposed to be any Glue or Hose Clamps on anything according to LG. Squeeze clamps only. Most of the LG washers had to be reconditioned, then sold as new. The hose is 2 inches too short and the travel of the tank, to offset a lopsided load, will one day rip that hose off. I repaced 12" of drywall in my whole washroom. Contact the FTC.
thanks for the comment. Mine (Panasonic) had a squeeze clamp which leaked so i changed it to a cable tie which works very well. The pipe length was short which i think resulted into too much pulling on the hose.
Can soap powder be the reason for a crack in the spider wheel?
Righty loosely!!!!! Thanks buddy!
What direction to unlocked the drum locknut , clock wise or anti clockwise ?
Thank you sir
My Problems is after removing all the screw the drum hardly came out stuck tight cant renove out , can pls advise thks boss
Same problem, I applied some WD40 and moved the drum while holding the outer tub. After a while it came out
good job
DANKIE!!
How about all the wire connected to the drum need remove them ?? Thks boss
I have taken close up pics of the nut and it appears that my machine has got counter clockwise thread? Do they differ from model to model??
indeed, some close turning to the right side and other to the left side, there is a legend in the "spider" under the nut with the directions
Hi, do I have to turn clockwise to open the 38mm nut? In your video, it turns clockwise while you were using the impact driver.
Yes. It’s reverse thread.
Hi sir.. I have problem on my washing machine Sharp.. Not big problem.. Just heard there water stuck on the drum.. even i finished use it.🤔. can you suggest me what can i do to solve this problem.😊 I'm little bit worried because just bought it about 5 months ago😑😁
Same here, that plate that was first removed mine got broken from down like what he just changed
Let me suggest to you Sir the drain hose or the drain pump is the area of CONCERN :
( UNPLUG WASHINE MACHINE FIRST FROM POWER SUPPLY )
1. Disconnect the two CONNECTING HOSES
AFTER DISCONNECTING YOUR TWO WATER HOSES FROM COLD AND HOT CONNECTIONS .
2. TILT YOUR W / M on ONE SIDE to locate the drain pump.
3..Normally TWO SECURITY MOUNT SCREWS SECURED THE BASE OF THE PUMP. UNDO THE TWO ( 2 ) SCREWS ..
4.. AND REMOVE THE PUMP AND REMOVE THE HOSE CLAMPS ON EACH HOSE..
5.. CHECK THE INSIDE OF THE PUMP FOR ANY FLUFF RETARDING THE ROTATION AND REMOVE ( IF ANY FLUFF ) INSIDE.
6.CHECK ALSO THE PUMP BEARINGS IF NOT DAMAGE..
7.. THE DRAIN HOSE ? FLUSH WITH THE SUPPLY WATER ( BOTH ENDS ) DETERMINE IF WATER FLOWS FREELY.
8.. IF EVERYTHING SEEMS ALRIGHT , .AKE SURE THERE IS NO KINK / S ON THE DRAIN HOSE ON TEST .... PUTTING YOUR WASHING MACHINE TO FILL UP AND . GO TO SPIN RUN AND CHECK THE VOLUME OF WATER COMING OUT.... ALL SHOULD BE ALRIGHT..
9... THAT IS WHY THERE IS A LEFT OVER OF WATER UNDER THE BOWL SIR ... BECAUSE OF IMPROPER PUMP ACTION.
10... ENJOY , BE SAFE AND ... ALWAYS HAVE FUN....And help is always available....
11.. REINSTALLATION ; IS THE PROCESS IN REVERSE.... YOU CAN ... MAKE THE BEST..
After 5 year samsung washing top load automatic washing machine, the inner stainless steel fully rusted and bent,,sir is there washing coming with plastic, with out stainless steel?
if yours was stainless steel it should not have rusted. Maybe it was coated that came of and then the metal underneath rusted. If it was stainless steel, you probably can claim a warranty from Samsung. I have not seen plastic drums
Thanks again ❤ how can u fix my
Am I hearing a fellow South African accent?
What is the spanner size please
Great
actually i removed the drum and i fixed it but the water is not stopping to flow out of the pipe why is it?
Tq
good
Machin aur scru bit ka koi link he kya
sir what is the size of that biggest nut you removed?the last one
Size was: 38mm
👍👍
I have an inherited 1982 GE top-loading machine myself. It leaks shortly after being turned on. The repairman tilted it, and said: " The drum is rusted through...time for a NEW one."
I know I can't complain having it all these years, but there IS planned obsolescence there. Why can't they use stainless, or at least galvanized steel?!?
Washing machine no power supply..already check 3 pin pluq..no problem.but still no power..what problem it that?
Can u give a link to help me i want to remove adrum from simpson front loader washing machine
Can you please share the link of impact driller used and socket attachment
Is the top nut thread in the normal direction i.e., anticlockwise??
normal
@@ecologicaltime what is the spanner size ?
@@manojmorajkar107 38
Top loader LG auto 12.0kg.any one know what problem ?
how was the issue fixed ??? where is the video ??
If you want to see how to fix, here are some repair videos: th-cam.com/play/PLYY5TJHy2astU91OYfnXiThLeZJT5dgYr.html
really amazed by your prompt reply I appreciate it ....kindly advise me why my machine drum is banging and shaking like hell in spinning cycle ....it feels so loose when touched (what is to be replaced?)...the machine is hardly 5 mths from purchase (missing warranty docs) model T7288NDDL lg fully automatic top loader....... just started all of a sudden during spin cycle
I have a similar setup inside my Samsung HE top load washer, but the drum seems to be seized on that spindle on the center. The locking nut and the washer come off with the right tools but I can't lift the drum off.
I have had WD-40 (penetrating oil) sitting in a little pool around the spindle for a couple days but it has not made any difference. I've also set up quickclamps around the drum to provide constant upwards pressure over time. Still nothing. Even tapping things with a mallet. Nothing. I'm going to throw out my back just trying to get this drum out and it still seems impossible. I have like a months worth of clothes on standby and this mf thing needs cleaning before any of that can happen. Anybody got any ideas?
Either something i can't see or find any evidence of is keeping the drum from lifting up, or some washer or component has corroded and debris has caused it to seized. It's a 7 year old machine.
You need to say “I’ll be back” lol
Terminator reference
To remove pulsetor just push it at center and pull it
Plz help me
Broke my drum and machine does not work and not power on
So I can here just to see how to unlock the top and get something that fell between the crack of the washing machine
He seems to be South African 🧐
That’s a lot of work to find missing socks
ha ha ha, good one
There is no drum removing, waste of my time
you never watched the whole video then as the drum is removed in this video