I wanted to give my review after completing this for my 2010 toyota corolla. 1st of THANK YOU you saved me a lot of money and my car! All of my lights came on (break, airbag, tire pressure, and I cannot remember the last one, but no check engine light) none of my guages worked and my ac ran hot. I could not run any codes and only recieved an error. So when I saw this video I wanted to give it a shot. All these steps are spot on. There are a few note I would like to add there are screws for the 1st panel thay needs to ne removed so unscrew those before you start pulling. Also, the steering wheel could be hard to wiggle off. You must hit on the back of the wheel to loosen it. You can also use a hammer if you cannot get it to budge. I found hitting the bottom towards the driver seat most effective. Other then that some of the airbags come off differently then the one he shows if you have the red and black clips with the yellow tab pull those up (gently) and then remove the red and black connectors from the air bag. 1 final note the bolt on the steering wheel is a bit hard to grt off use a torque wrench for easier removal. All my lights went off, power steering came back and my gauges are functioning and my ac now gets cold again. All of this stopped working on my car due to this issue. My car runs perfectly fine now with this video some tools and a $180 steering angle sensor from carid. I am a woman and if I can do it so can you!
Hello Deborah. I am honestly glad that you managed to do it on your own without anyone's help which means you have a gifted talent. But isn't it strange that all these stopped working in your car because of this problem?
I would like to thank you for the video. It was very helpful in replacing my daughter SAS on her Corolla 2010. Her car was getting Steering, VSC, ABS lights on, odometer and RPM not working. I read on the Corolla forum to replace the SAS which I was surprise and shock but it was the problem. I bought the part from Rockauto for $125 and installed it. Mahalo....
I just can’t believe today I myself replaced the faulty clockspring in my 2011 Corolla Altis due to which the system was throwing check SRS system light. All of this done with the help of your video and the light’s gone too. You and the internet combined saved me a few thousand bucks today. So grateful. Best wishes from India.
Love the music, if you compress the sides of the bottom steering column panels and pill down it pops out in one smooth move, and there's to catches on the top that if you pry back a tiny bit the top comes off just as easy
My 2011 Corolla LE has cruise control. The clock spring I bought on Amazon worked fine but there was a module snapped onto the back of the old clockspring for the steering sensor. I was able to put that module onto the clockspring I bought and then everything matched up. Depending on what comes with your new clockspring you may need to reuse that steering sensor on the new one.
Thanks to you for the video, I didn't know how to disconnect the harnesses from the air bag. It helped me define that the lack of connection lies precisely in that mechanism. Again thanks.
i dont mean to be off topic but does someone know of a trick to get back into an instagram account..? I stupidly forgot the account password. I would appreciate any help you can offer me
@Anders Julius thanks so much for your reply. I found the site through google and I'm waiting for the hacking stuff atm. Takes quite some time so I will reply here later when my account password hopefully is recovered.
Έχετε ακριβώς αυτό που χρειάζομαι αυτή την στιγμή, κατάφερε η μικρή μου η κόρη και τύλιξε ένα λαστιχακι μέσα στο τιμόνι,με αποτέλεσμα για την ώρα να έχω σφιχτή αίσθηση (προφανώς θα έχει κουλουριαστει στα εσωτερικά πλαστικά κουμπώματα) και θα χρειαστεί να ξεμονταρω το τιμόνι. Μου λύσατε τα χέρια με το βίντεο που ανεβάσατε. Μένει μόνο να το τολμήσω 😂! Καλό και ευλογημένο Πάσχα να έχετε.
Εύχομαι να πάνε όλα καλά φίλε μου και χωρίς προβλήματα.Μεγάλη προσοχή στην λεπτομέρεια. Αφαίρεση οποιοδήποτε εξάρτημα για να ελευθερώσεις το τιμόνι από το λαστιχάκι. Καλό Πάσχα και καλή Αναστάση εν ονόματι Κυρίου
@@YiannisPagonis Χρόνια πολλά Χριστός Ανέστη. Τελικά δεν αποφύγαμε την ζημιά,το λαστιχακι κατάφερε να μπει μέσα στην σερπαντίνα και να την κόψει, οπότε αλλάχτηκε με καινούρια! Η δουλειά έγινε χάρη στο ολοκληρωμένο βίντεό σας!
@@MrAtlantic500 Χρόνια πολλά και αληθώς ο Κύριος. Τέλος καλά και όλα καλά με την ανεπάντεχη ζημιά που έγινε. Τι να γίνει συμβαίνουν και αυτά καμία φορά.
@@ramazankolukrk7567 Arkadaşım aşağıdaki 2 videoyu izle ve umarım düzgün bir şekilde kurmana yardımcı olurlar. th-cam.com/video/suuynH6nq9o/w-d-xo.html th-cam.com/video/t3fTMCwjVH4/w-d-xo.html
This is a good video with these video l can change my Toyota Corolla 2010 spira cable next time there is any issue. If l had watch your video l would have save more money last week l ended up paying $535 to Toyota workshop. My airbag light was on for couple of weeks l was told my spiral cable need to be change. The labour that costed $335 l would have save that to my pocket. Spiral cable is just about $135 - $200. Thanks for your Time and the sharing of Knowledge God bless you
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may cause airbag deployment. INSTALL SPIRAL CABLE (a) Check that the front wheels are facing straight ahead. (b) Set the turn signal switch to the neutral position. NOTICE: If it is not in the neutral position, the turn signal switch pin may be snapped. (c) Install the spiral cable with the 3 claws. NOTICE: When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly. (d) Connect the connectors to the spiral cable. NOTICE: When connecting the airbag connector, take care not to damage the airbag wire harness. ADJUST SPIRAL CABLE (a) Check that the ignition switch is off. (b) Check that the cable is disconnected from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system. (c) Rotate the spiral cable counterclockwise slowly by hand until it stops. NOTICE: Do not turn the spiral cable using the airbag wire harness. (d) Rotate the spiral cable clockwise approximately 2.5 turns to align the marks. NOTICE: Do not turn the spiral cable using the airbag wire harness. HINT: The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
No, amigo mío, NO hay forma de que el airbag explote si desconectas el terminal negativo (y no el positivo) de la batería, así que no tengas miedo. ¡Pero existe el riesgo de que el airbag explote si NO desconecta la batería!
If the clock spring is failing, it may become difficult to turn the steering wheel, or the steering wheel may have a “stiff” or “binding” feel. This often disables some radio and cruise control functions.
Yes right now I have no function for any of the steering wheel buttons such as cruise control or control of the radio and paddle shifters, air bag light is also on for circuit code, but everytime I turn the steering wheel to the right the paddle shifter mode turns on and the radio also gets functions like volume up or down and switch stations
Can you replace the steering wheel of a 2009 LE model with the steering wheel of a corolla S? And be able to control the radio with the controls in the steering wheel? Se puede cambiar el volante de un Corolla versión LE por uno version S con mandos al timon, y lograr conectarlo para controlar la radio mediante los mandos del timon??
@@YiannisPagonis thanks 4 replying do u know if it's possible to replace it with the Corolla s steering wheel? If it's possible to control radio through it? And + get the night light in the buttons?
Είδα το βίντεο και θέλω να μου δώσεις λύση σε ένα τσικ τσικ που κάνει στο στρίψιμο του τιμονιού. Έφτασα στο σημείο της αντικατάταστασης του εξαρτήματος μα και με το καινούργιο το ίδιο μου κάνει. Μήπως φταίει κάτι άλλο; Όταν καθαρίζω το τιμόνι με υγρό πανί σταματάει
What I want to to know is can I take a steering wheel from let say the latest hilux with steering control buttons and put it in a car without those using the newer head units
@@YiannisPagonis Do you happen to know what foot-poundage to torque it to? I installed mine too firmly and it ended up crunching the clockspring housing when I tried to turn it.
Confira no link abaixo meu amigo e encontre exatamente o que você deseja www.megazip.net/zapchasti-dlya-avtomobilej/toyota?network=g&adposition=&keyword=%2Btoyota%20%2Bcorolla%20%2Bparts&gclid=Cj0KCQiA2uH-BRCCARIsAEeef3nF3pvKBE4tuJQhYtsMEI8lTCoRO_2eFxWhESqKMirkbcZYxkIwAQsaApGkEALw_wcB
At 6.34, are you saying the arrow needs to be lined up? Apart from that and making sure the steering wheel goes back on the same tooth, anything else to make sure of?
My friend what you should notice when installing this part of the car is that the ends of these 2 arrows should be joined in a vertical straight line. If you look carefully you will see that there are 2 arrows and not 1 arrow.
Amigo le puedo poner a mi Toyota Corolla 2004 un mando multifuncional del corolla 2016 mi carro no trae nada de mandos pero ya conseguí el volante ?? Espero y me pongo puedas apoyar
Γιάννη μου έλυσες τα χέρια και έλεγα πως βγαίνει το καπάκι που κρύβει τις ασφάλειες κατω από την κολόνα του τιμονιού. Το προσπάθησα πριν να δω το βίντεο και επειδή δεν έβγαινε το άφησα μην και κανω καμιά ζημιά,τελικά θέλει πιο πολύ δύναμη.
Γιώργο ξέρω ότι είναι πολύ δύσκολο για να βγει, ιδίως μετά από κάποια χρόνια. Θέλει ιδιαίτερη προσοχή για να μην γίνει καμία ζημιά. Εκτός από δύναμη θέλει και τεχνική.
Tell me, my friend, how did you install the steering wheel. Did you place front wheels facing straight ahead and then lock the steering wheel by removing the car key? Before removing the steering wheel did you put alignment marks on the steering column and your new steering wheel? Did you do anything else after that? (e.g. on the bars and wheel links)
@@YiannisPagonisYiannis, thank you for your kind answer. I didn't do the marks on columns and new wheel. My bad. I think I turned the steering wheel accidentally when I screw this bolt on. I didn't do anything more: the bars, wheels links etc. Only steering wheel. Is there any chance to reintstall correctly the steering wheel now? or do I have to do this wheels links stuff and ->alingment then, as I think? Thank you for your time.
@@janjohnny4945 I'm sorry about that my friend. Because you didn't do what you were supposed to do, your car needs an alignment. It is not easy to do by you, like e.g. engine oil change, and must be done by a dealer or repair shop. It requires the right tools/machines and also the knowledge (experience) to properly align your vehicle. I am sorry 🙁🙁
Thanks my friend for your kind words. Yes indeed I am 100% Greek. I was born and raised in Macedonia, Greece, the country where Alexander the Great was born
@@YiannisPagonis I got them loose easy enough but the air bag still would not come out. I had to keep working the screws with needle nose pliers and small hooks to get it far enough out to remove air bag. took me 20 min. but thanks for the response
You are doing God's work for many Corolla owners out there!
Just my friend I do my duty, my debt to the Corolla holders
I wanted to give my review after completing this for my 2010 toyota corolla. 1st of THANK YOU you saved me a lot of money and my car! All of my lights came on (break, airbag, tire pressure, and I cannot remember the last one, but no check engine light) none of my guages worked and my ac ran hot. I could not run any codes and only recieved an error. So when I saw this video I wanted to give it a shot. All these steps are spot on. There are a few note I would like to add there are screws for the 1st panel thay needs to ne removed so unscrew those before you start pulling. Also, the steering wheel could be hard to wiggle off. You must hit on the back of the wheel to loosen it. You can also use a hammer if you cannot get it to budge. I found hitting the bottom towards the driver seat most effective. Other then that some of the airbags come off differently then the one he shows if you have the red and black clips with the yellow tab pull those up (gently) and then remove the red and black connectors from the air bag. 1 final note the bolt on the steering wheel is a bit hard to grt off use a torque wrench for easier removal. All my lights went off, power steering came back and my gauges are functioning and my ac now gets cold again. All of this stopped working on my car due to this issue. My car runs perfectly fine now with this video some tools and a $180 steering angle sensor from carid. I am a woman and if I can do it so can you!
Hello Deborah. I am honestly glad that you managed to do it on your own without anyone's help which means you have a gifted talent. But isn't it strange that all these stopped working in your car because of this problem?
Best comment ever. These steps saved me as well lol. Thank you strong capable lady 😊
Did you also replace the clock spring or just the sensor??
I would like to thank you for the video. It was very helpful in replacing my daughter SAS on her Corolla 2010. Her car was getting Steering, VSC, ABS lights on, odometer and RPM not working. I read on the Corolla forum to replace the SAS which I was surprise and shock but it was the problem. I bought the part from Rockauto for $125 and installed it. Mahalo....
Same issue with my 2010. I will be replacing mine this weekend I will let you know if mine is fixed too.
Great work Mr. Pagonis. You have solution for virtually every possible issue. Kudos and Thanks!
Thank you my friend Sahil. I am doing the best I can. Greetings from Greece.
I just can’t believe today I myself replaced the faulty clockspring in my 2011 Corolla Altis due to which the system was throwing check SRS system light. All of this done with the help of your video and the light’s gone too. You and the internet combined saved me a few thousand bucks today. So grateful. Best wishes from India.
@@saxenaji Thanks my friend from India. I am from Greece. I just did my duty and nothing more.
Hace un año miré este tutorial y hoy 30 de Mayo del 2020 lo miro de nuevo,un excelente tutorial, saludos desde Sonora México
Gracias mi amigo y siempre estarás bien. Saludos desde Mitilene, Grecia.
Your video guided me through the successful replacement of the clock spring in my 2006 Corolla . Thank you! 🥰🇨🇦
You are welcome
Love the music, if you compress the sides of the bottom steering column panels and pill down it pops out in one smooth move, and there's to catches on the top that if you pry back a tiny bit the top comes off just as easy
Thank you very much for your observation
My 2011 Corolla LE has cruise control. The clock spring I bought on Amazon worked fine but there was a module snapped onto the back of the old clockspring for the steering sensor. I was able to put that module onto the clockspring I bought and then everything matched up.
Depending on what comes with your new clockspring you may need to reuse that steering sensor on the new one.
Try it my friend and I hope everything goes well without problems
Thanks to you for the video, I didn't know how to disconnect the harnesses from the air bag. It helped me define that the lack of connection lies precisely in that mechanism. Again thanks.
My friend, as long as someone lives, he learns, so do I.
Vi
i dont mean to be off topic but does someone know of a trick to get back into an instagram account..?
I stupidly forgot the account password. I would appreciate any help you can offer me
@Dario Finley instablaster =)
@Anders Julius thanks so much for your reply. I found the site through google and I'm waiting for the hacking stuff atm.
Takes quite some time so I will reply here later when my account password hopefully is recovered.
Έχετε ακριβώς αυτό που χρειάζομαι αυτή την στιγμή, κατάφερε η μικρή μου η κόρη και τύλιξε ένα λαστιχακι μέσα στο τιμόνι,με αποτέλεσμα για την ώρα να έχω σφιχτή αίσθηση (προφανώς θα έχει κουλουριαστει στα εσωτερικά πλαστικά κουμπώματα) και θα χρειαστεί να ξεμονταρω το τιμόνι.
Μου λύσατε τα χέρια με το βίντεο που ανεβάσατε.
Μένει μόνο να το τολμήσω 😂!
Καλό και ευλογημένο Πάσχα να έχετε.
Εύχομαι να πάνε όλα καλά φίλε μου και χωρίς προβλήματα.Μεγάλη προσοχή στην λεπτομέρεια. Αφαίρεση οποιοδήποτε εξάρτημα για να ελευθερώσεις το τιμόνι από το λαστιχάκι. Καλό Πάσχα και καλή Αναστάση εν ονόματι Κυρίου
@@YiannisPagonis Χρόνια πολλά Χριστός Ανέστη.
Τελικά δεν αποφύγαμε την ζημιά,το λαστιχακι κατάφερε να μπει μέσα στην σερπαντίνα και να την κόψει, οπότε αλλάχτηκε με καινούρια!
Η δουλειά έγινε χάρη στο ολοκληρωμένο βίντεό σας!
@@MrAtlantic500 Χρόνια πολλά και αληθώς ο Κύριος. Τέλος καλά και όλα καλά με την ανεπάντεχη ζημιά που έγινε. Τι να γίνει συμβαίνουν και αυτά καμία φορά.
Merhabalar çok başarılısınız tebrik ederim turkiyeden izliyorum 2008 1.6 corolla aracima hiz sabitleme yapamıyorum yardimci olurmusunuz nasil bi yol izelemem gerekli
Merhaba arkadaşım ve çok teşekkür ederim. Hız göstergenizde tam olarak ne var? Hız göstergesinde ne gibi bir sorun yaşıyorsunuz? Belirtileri nelerdir?
Cruise control takmak istiyorum fakat direksiyon üzerindeki soket boş ne yapmam gerekiyor
@@ramazankolukrk7567 Arkadaşım aşağıdaki 2 videoyu izle ve umarım düzgün bir şekilde kurmana yardımcı olurlar.
th-cam.com/video/suuynH6nq9o/w-d-xo.html
th-cam.com/video/t3fTMCwjVH4/w-d-xo.html
This is a good video with these video l can change my Toyota Corolla 2010 spira cable next time there is any issue. If l had watch your video l would have save more money last week l ended up paying $535 to Toyota workshop. My airbag light was on for couple of weeks l was told my spiral cable need to be change. The labour that costed $335 l would have save that to my pocket. Spiral cable is just about $135 - $200. Thanks for your Time and the sharing of Knowledge God bless you
Thank you very much my friend
Do you need to turn the clock spring 5 times one way and 2.5 the other before you line it up? Or is it as simple as lining up the arrows?
The spiral cable is an important part of the SRS airbag system.
Incorrect removal or installation of the spiral cable may cause airbag deployment.
INSTALL SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Set the turn signal switch to the neutral position.
NOTICE:
If it is not in the neutral position, the turn signal switch pin may be snapped.
(c) Install the spiral cable with the 3 claws.
NOTICE:
When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.
(d) Connect the connectors to the spiral cable.
NOTICE:
When connecting the airbag connector, take care not to damage the airbag wire harness.
ADJUST SPIRAL CABLE
(a) Check that the ignition switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Rotate the spiral cable counterclockwise slowly by hand until it stops.
NOTICE:
Do not turn the spiral cable using the airbag wire harness.
(d) Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
NOTICE:
Do not turn the spiral cable using the airbag wire harness.
HINT:
The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
Amigo una consulta , al desconectar la bateria no hay riesgo que el airbag explote no? Ese es mi miedo por que tengo que hacerlo y es mi duda. Gracias
No, amigo mío, NO hay forma de que el airbag explote si desconectas el terminal negativo (y no el positivo) de la batería, así que no tengas miedo. ¡Pero existe el riesgo de que el airbag explote si NO desconecta la batería!
What tools did you use?
how you was able to open the key switch with the battery disconnected?
You mean at 4:35?
What size of T screw did you use to take out the nuts please on both side of the airbag
It is TORX T30 my friend
@@YiannisPagonis Thank you so much for the quick reply
@@theoboateng5408 You are welcome my friend Theo
Can this cause the radio and paddle shifter to function on its own when I make a right turn only?
If the clock spring is failing, it may become difficult to turn the steering wheel, or the steering wheel may have a “stiff” or “binding” feel. This often disables some radio and cruise control functions.
Yes right now I have no function for any of the steering wheel buttons such as cruise control or control of the radio and paddle shifters, air bag light is also on for circuit code, but everytime I turn the steering wheel to the right the paddle shifter mode turns on and the radio also gets functions like volume up or down and switch stations
@@mularock2352 My friend check the Clockspring
What is that center screw called? Right smack in the middle of the clock spring. Is it a shaft?
I honestly didn't understand what exactly you want to tell me
Just what I needed! Thanks m8!
You are welcome m8!
Para un toyota corolla 2009 hay que hacer el mismo procedimiento?
Si mi amigo es exactamente el mismo proceso
Looks like Toyota corolla verso 2005 year . Is this the same?
Really wish you would have told what size torques and what size nut for the steering wheel
I do appreciate the video I just wish there was sizes for what tools were used thank you
Can you replace the steering wheel of a 2009 LE model with the steering wheel of a corolla S? And be able to control the radio with the controls in the steering wheel?
Se puede cambiar el volante de un Corolla versión LE por uno version S con mandos al timon, y lograr conectarlo para controlar la radio mediante los mandos del timon??
If I had a such 2009 Corolla LE I would do it my friend
@@YiannisPagonis thanks 4 replying do u know if it's possible to replace it with the Corolla s steering wheel? If it's possible to control radio through it? And + get the night light in the buttons?
@@loganrage3047 Yes I think it can be done what you want to do
I have a Corolla 2009 with an airbag light on and diagnose that need to replace this part, video was very helpful, thanks.
Thank's too, my friend.
Hi Firstly thanks for sharing this with us, I’m not good at all with cars, can you tell me the name of the tool you are using at 4.27? Thanks
It's name is ''Ratchet Handle Socket Wrench with extension'' my friend.
Yiannis Pagonis thanks very much!
@@z4b431 You are welcome my friend
Είδα το βίντεο και θέλω να μου δώσεις λύση σε ένα τσικ τσικ που κάνει στο στρίψιμο του τιμονιού. Έφτασα στο σημείο της αντικατάταστασης του εξαρτήματος μα και με το καινούργιο το ίδιο μου κάνει. Μήπως φταίει κάτι άλλο; Όταν καθαρίζω το τιμόνι με υγρό πανί σταματάει
My tourqe spit screws are not coming out any tips?
Do you mean that you can not unscrew the steering wheel nut?
What I want to to know is can I take a steering wheel from let say the latest hilux with steering control buttons and put it in a car without those using the newer head units
Is what you want to do compatible? Does it fit in the car you want to install?
@@YiannisPagonis yes man I want to take from the revo hilux the steering wheel and head unit put in passo 1st Gen think it should work with the wiring
@@saddammalima8458 I'm afraid this can not be done my friend!
@@YiannisPagonis why not? It's just changing the clock spring and wiring
@@saddammalima8458 Then change it and tell me the result of this change
What size of socket would I need for the nut on the steering column?
It is 19 mm socket my👭👬👫 friend😊😇
Thank you brother🙏🏼🙏🏼
@@hamzashetranjiwala3885 You are welcome my friend
@@YiannisPagonis Do you happen to know what foot-poundage to torque it to? I installed mine too firmly and it ended up crunching the clockspring housing when I tried to turn it.
@@stephanieaensland6520 Interested in learning about the steering wheel nut? Did the installation the clockspring work properly?
Tell me please how to take the yellow clip apart please
My friend, do you mean how to remove the yellow cable from clockspring part?
what is the socket size to open centre bolt????
It is 19 mm socket my friend
Sabe dizer essa peça para um Corolla 2010/2011 XLI sem comando no volante qual seria o número de código dela, para poder comprar
Confira no link abaixo meu amigo e encontre exatamente o que você deseja
www.megazip.net/zapchasti-dlya-avtomobilej/toyota?network=g&adposition=&keyword=%2Btoyota%20%2Bcorolla%20%2Bparts&gclid=Cj0KCQiA2uH-BRCCARIsAEeef3nF3pvKBE4tuJQhYtsMEI8lTCoRO_2eFxWhESqKMirkbcZYxkIwAQsaApGkEALw_wcB
What is the part number?
Que falla te presentaba?
No hay problema. El video es un tutorial.
At 6.34, are you saying the arrow needs to be lined up? Apart from that and making sure the steering wheel goes back on the same tooth, anything else to make sure of?
My friend what you should notice when installing this part of the car is that the ends of these 2 arrows should be joined in a vertical straight line. If you look carefully you will see that there are 2 arrows and not 1 arrow.
Whith no words it’s all said... excellent!!
Thanks
A picture speaks a thousand words
How are you my friend?
Excellent
Thank you my friend ❤❤❤❤❤❤❤❤
Amigo le puedo poner a mi Toyota Corolla 2004 un mando multifuncional del corolla 2016 mi carro no trae nada de mandos pero ya conseguí el volante ?? Espero y me pongo puedas apoyar
Me temo amigo mío que lo que pides no se puede hacer porque simplemente no cabe en tu coche para hacer esta nueva instalación.
@@YiannisPagonis o sabrás de algún otro modelo con mandos que le pueda cambiar ?
@@FerniAntrax. No estoy seguro de responderte. Lo siento
Muchas gracias!!! Me sirvió mucho su video!
De nada mi amigo ❤❤❤❤
Good , keep going
Thank you very much my friend 🙏🙏
Thanks my friend! I replaced my Auris 2011 clockspring with directions from your video :)
You are wellcome my friend. I am glad to help you
How are you my friend?
can someone repair and fix clock spring
2013 is different. There's a clip you push on either side to release the airbag
Yes, there are some differences between them
BUENOS DÍAS LA PERSONA QUE ESTÁ FIRMANDO EL VIDEO AL FINAL LE COLOCO LA CÁMARA EN LA CABEZA COMO SI HAY TUBIERA LA CINTILLA
i would first remove the air bag steering wheel then remove plastics and replace the clockspring,would be easier to change
Do we need to change everything after airbag brust?
Which parts should I change after air bag brust??
Clock spring , air bag, and impact sensors where it was hit .
good job
You are welcome my friend ❤❤
how dangerous is this to do?
Attempting to replace an airbag yourself can be very dangerous, especially if you do not have any prior experience doing so.
Thank you
You are welcome my friend ❤❤❤❤
Thank you! 😌
You are welcome 🙏 my friend 😊😊
You are welcome 🙏 my friend 😊😊
Some segments in the video are stamped not adjacent to each other
Muchas gracias me sirvio mucho, excelente 👍🏻👍🏻👍🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
Es una gran alegría pero también un honor haberte ayudado amigo mío. Que Dios te tenga bien y te proteja de todo mal.
Γιάννη μου έλυσες τα χέρια και έλεγα πως βγαίνει το καπάκι που κρύβει τις ασφάλειες κατω από την κολόνα του τιμονιού. Το προσπάθησα πριν να δω το βίντεο και επειδή δεν έβγαινε το άφησα μην και κανω καμιά ζημιά,τελικά θέλει πιο πολύ δύναμη.
Γιώργο ξέρω ότι είναι πολύ δύσκολο για να βγει, ιδίως μετά από κάποια χρόνια. Θέλει ιδιαίτερη προσοχή για να μην γίνει καμία ζημιά. Εκτός από δύναμη θέλει και τεχνική.
Anyone I have changeed my steering wheel. It is not straight when wheels arte straight. Damn!.
Tell me, my friend, how did you install the steering wheel. Did you place front wheels facing straight ahead and then lock the steering wheel by removing the car key? Before removing the steering wheel did you put alignment marks on the steering column and your new steering wheel? Did you do anything else after that? (e.g. on the bars and wheel links)
@@YiannisPagonisYiannis, thank you for your kind answer. I didn't do the marks on columns and new wheel. My bad. I think I turned the steering wheel accidentally when I screw this bolt on.
I didn't do anything more: the bars, wheels links etc. Only steering wheel.
Is there any chance to reintstall correctly the steering wheel now? or do I have to do this wheels links stuff and ->alingment then, as I think? Thank you for your time.
@@janjohnny4945 I'm sorry about that my friend. Because you didn't do what you were supposed to do, your car needs an alignment. It is not easy to do by you, like e.g. engine oil change, and must be done by a dealer or repair shop. It requires the right tools/machines and also the knowledge (experience) to properly align your vehicle. I am sorry 🙁🙁
@@YiannisPagonis thank you for your time and information.
Thank you sir. And I can tell you are a handsome man even from just seeing your chin (and of course, knowing that you are possibly Greek!)
Thanks my friend for your kind words. Yes indeed I am 100% Greek. I was born and raised in Macedonia, Greece, the country where Alexander the Great was born
Do you know the torque spec for the nut on the steering wheel shaft?
Torque: 50 n·m (510 kgf·cm, 37 ft·lbf)
www.tcorolla.net/
How are you my friend?
Can you please tell the parte Numbers for that Toyota from 2008?
Airbag or Clockspring?
@@YiannisPagonis clockspring
@@ivobruno1136 The part number for clockspring is 84306-02190 (TOYOTA COROLLA, YARIS,VIOS, 2008-2013).
@@YiannisPagonis thank you very much 👌
@@ivobruno1136 You are welcome my friend
you saved me $250 of labor from canadian tire lol.
Really now? Here in Greece it costs only 80 Euros! They are very expensive in your country!!!! LOL
My friend , could you tell this codes are for which issues exactly: B01901 & B01906 , Toyota Avanza 2015 , I appreciate your efforts, Thanks
What problem do you have my friend with your car?
you edited out how to get the t30 screws out to remove air bag. mine seem to be stuck and wont come out of hole. how did you do it?
My friend, to loosen the 2 screws, first spray a little anti-rust on the screws and then hit them with the T30 using a small extension
@@YiannisPagonis I got them loose easy enough but the air bag still would not come out. I had to keep working the screws with needle nose pliers and small hooks to get it far enough out to remove air bag. took me 20 min. but thanks for the response
@@csul5961 Did you finally make it my friend? Everything went well;
@@YiannisPagonis yes it all set. I used your video to replace my broken cruise control. thanks
@@csul5961 I'm so happy to hear that. I had a great concern
bravo!
Thank you my friend 😀😀😀😀😀😀
Uuga Buga ! Uga Buga !
Muxuu yahay buugani? Waa maxay;
Worst part is getting the steering wheel dead centered. If its off just a little its annoying to drive.
in Europe this guide is only suitable for Corolla until 2010 year
You are right my friend. There are several differences of this generation depending on the continent for which it is intended.
What’s up bro you can play Young Jeezy. Oh that’s right I forgot no copyrights.
Or do you prefer "bouzouki" music?
@@YiannisPagonis 👍👍👍
@@mynameischucky.charlesleer4363 OPA OPA OPA. LET'S DANCE!
Can anyone here shed some light on the steering with the control conversion?
Great video. Thanks a lot
Thank you
Muy bien me gustó.
Ευχαριστώ πολύ φίλε μου και να'σαι καλά.
YO PRIMERO QUITARÍA LA CABRILLA Y QUEDA MÁS CÓMODO SACAR LAS COCAS DESPUÉS
La musica de fondo.hecho a perder el video.
Es verdad? Cómo pasó esto? AY DIOS MÍO!!!!
😊😊👍⋯⋯🎉
Thank you very much my friend ❤❤❤❤❤❤