Dude you really have the best channel for information I’m just getting into boats and every time I search for something your videos are the best…. Thank you
Fascinating..... I've been a big proponent of 1:20 scale hydro racing (about 16" ~ 18") for some time and am running some of the same motors you've been discussing here in my scale boats. The outrunner motor you review here is a 450 size helicopter motor and there's a HUGE selection available in varying length, diameters, and Kv. I bought the last of those FRP outriggers based on your reviews because I'm sure I can get it to stop hopping...
I'm actually about to replace the stuffing tube and run it under the tub. I know that's what it is. I actually took it out today for a quick test. I moved the turn fin back to where my cg is and she was running pretty good. Still has a little bounce at lower speeds. Thanks for watching.
I recently purchased my first RC boats, an FT012 and an Atomic. Only had them out twice and I already want to build a boat. The wide range of motors, batteries, ESC's etc makes it complicated for someone new to the hobby like me. I really appreciate you putting this video together as it helped me improve my knowledge. Looking forward to buying some parts and start building. Thanks!!!!
@@IRONCLADRC I can't speak from knowledge or experience because I'm new but I REALLY like the Atomic catamaran. One reason I purchased these two boats was to learn and experience some of the differences between them. The FT012 is a V hull and it has trim tabs and stabilizers on the rear. The Atomic is a catamaran without trim tabs and stabilizers. To my surprise the catamaran handles WAY better without the extra hardware the FT012 has. The Atomic got up on plane quicker and it turns on a dime! I guess it's the difference in the hull design? I paid $130 for the Atomic and couldn't be happier.
Good afternoon, please tell me there is a problem with 40a ESC, as soon as the voltage of the 3S battery drops below 11.2 volts, the boat cannot go at full acceleration, when you push it to the end, the boat just stops and you need to release the pedal again and start again and do not press to the end. Thank you.
You more than likely have the boat "over propped for that speed control, maybe try going down in prop size to reduce load? Could also be the low voltage cut off letting you know to bring the boat in and Change batteries
Thank you for this video I just bought 4 of the Trex 450 motors & 50amp shark esc for my 600mm 3D printed boat! Should FLY on 4s from what I am seeing thank you
Got a couple of questions for you if you don't mind answering. I have a Proboat Widow Maker, that only can handle 2s lipo. Wanted to upgrade the boat to accept 3s to 4s lipo and i'm not sure if the stock motor can handle 3s and it probably won't handle 4s. If i buy the ZTW esc, what motor do you think i need to put with the ZTW esc? I would buy the other option you used for the video but i don't like buying from China & waiting 2 months...i think you get my drift. Ty for your help in advance brotha!
So, I just toasted my 2000kv 6 pole motor on my Veles 29” pro boat. I’m using 1716 prop two 5000mah 50c 3s. What would you recommend for a motor? I just did the two water lines upgrade this was the maiden voyage with the prop. Thanks for any information.
@@IRONCLADRC 👍..can you do a destruction test on one of your motors like set it up in a mount and give it full revs until it blows or not,I bet the Outrunner lasts longer as it cools itself
Iv just brought this shark esc on my motor iv got red black and yellow wire on esc there all black lol does it matter wot one goes where iv not tried it yet as I don’t wanna blow out
Plug the 2 middle wires together the 2 outside wires don't really matter which one you plug in to one another. The 2 outside wires change the motor direction. Hope this helps
@@IRONCLADRC Errm so two out side wires are red/black and middle wire is signal then yeah ? Think that’s wot I’m getting from your reply ? As you mentioned 2 middle wires and 2 outside but there’s only 3 in total
Dude you really have the best channel for information I’m just getting into boats and every time I search for something your videos are the best…. Thank you
You have so many collection of boat parts. I am always watching your videos my friend. Take care
Fascinating..... I've been a big proponent of 1:20 scale hydro racing (about 16" ~ 18") for some time and am running some of the same motors you've been discussing here in my scale boats. The outrunner motor you review here is a 450 size helicopter motor and there's a HUGE selection available in varying length, diameters, and Kv. I bought the last of those FRP outriggers based on your reviews because I'm sure I can get it to stop hopping...
I'm actually about to replace the stuffing tube and run it under the tub. I know that's what it is. I actually took it out today for a quick test. I moved the turn fin back to where my cg is and she was running pretty good. Still has a little bounce at lower speeds. Thanks for watching.
Uuyy
Yyuuuy 😝 TH-cam yuyyyy
Yuu
Y
First again 👍👍👍👍 I'm getting good at this lol.. I just watched your backflip video 🤣👍
That was a perfect flip. Oh man couldn't do that again if I tried. 😆
Hi man here Sebastiano from Italy. Seaking 40a is rtr..... So it doesn't need programming? I adore you man, remember that you are my guruboat
I wouldn't say it doesn't need programming It can be programed using your remote control
I recently purchased my first RC boats, an FT012 and an Atomic. Only had them out twice and I already want to build a boat. The wide range of motors, batteries, ESC's etc makes it complicated for someone new to the hobby like me. I really appreciate you putting this video together as it helped me improve my knowledge. Looking forward to buying some parts and start building. Thanks!!!!
The atomic catamaran? How did the atomic preform? GOOD LUCK with your build.
@@IRONCLADRC I can't speak from knowledge or experience because I'm new but I REALLY like the Atomic catamaran. One reason I purchased these two boats was to learn and experience some of the differences between them. The FT012 is a V hull and it has trim tabs and stabilizers on the rear. The Atomic is a catamaran without trim tabs and stabilizers. To my surprise the catamaran handles WAY better without the extra hardware the FT012 has. The Atomic got up on plane quicker and it turns on a dime! I guess it's the difference in the hull design? I paid $130 for the Atomic and couldn't be happier.
Good day sir..did you test the racestar 2835 on a boat using 4s??isn't gonna burned??
2835 burned on 3s with a prop that was to big for the motor. The 2835 actually handled 4s with a small prop under light loads.
Good afternoon, please tell me there is a problem with 40a ESC, as soon as the voltage of the 3S battery drops below 11.2 volts, the boat cannot go at full acceleration, when you push it to the end, the boat just stops and you need to release the pedal again and start again and do not press to the end. Thank you.
You more than likely have the boat "over propped for that speed control, maybe try going down in prop size to reduce load?
Could also be the low voltage cut off letting you know to bring the boat in and Change batteries
Thank you for this video I just bought 4 of the Trex 450 motors & 50amp shark esc for my 600mm 3D printed boat! Should FLY on 4s from what I am seeing thank you
Wow that's awesome 👌
hi what are the mount hole c/c on the 4000kv racestar 2835 ? 16mm ?
Sounds about right look on ebay for that motor they usually list the pattern size
Can u point me in the right direction to mount a water cool motor inrunner motor and also how to set up a water cool system
www.offshoreelectrics.com/proddetail.php?prod=ose-80080-c
Any suggestions for upgrade the UDI Arrow 005. Wanted to run 6s lipo. Two 3s series batteries. Looking for a nice motor and esc to much the upgrade.
Seaking or shark, which one is better?
The new v2 shark is a better choice, the v1 shark was better than the hobbywing
Big B here too =) , hey yall let's comment on every video and hit the like button... content like this deserves support 🤩BB
What's your thoughts on car esc' 🚗 I like a reverse... just run a h2o cooling plate instead of the fan 😎
It will work If you can waterproof it?
Got a couple of questions for you if you don't mind answering. I have a Proboat Widow Maker, that only can handle 2s lipo. Wanted to upgrade the boat to accept 3s to 4s lipo and i'm not sure if the stock motor can handle 3s and it probably won't handle 4s. If i buy the ZTW esc, what motor do you think i need to put with the ZTW esc? I would buy the other option you used for the video but i don't like buying from China & waiting 2 months...i think you get my drift. Ty for your help in advance brotha!
What's the length of the boat? Is it heavy for its size or light?
Hi bro can I ask where I can buy that one here in the PH?
I WAS THINKING ON THE MADFLOW V3 F1 TUNNEL RC BOAT AT MOTION RC. WHAT DO YOU THINK?
Yep. Never seen that one before.. she's got potential for sure
So, I just toasted my 2000kv 6 pole motor on my Veles 29” pro boat. I’m using 1716 prop two 5000mah 50c 3s. What would you recommend for a motor? I just did the two water lines upgrade this was the maiden voyage with the prop. Thanks for any information.
An tfl SSS brushless motor is a great upgrade
Hi is the Outrunner a t-rex 450 helicopter motor cause I have new one so this is good your testing it
Racerstar 2235 4000kv
@@IRONCLADRC 2835 4000kv ,must be re labled ,run 4s my goodness 😊
Yea I looks tobe the same like u said just rebranded or something.
@@IRONCLADRC 👍..can you do a destruction test on one of your motors like set it up in a mount and give it full revs until it blows or not,I bet the Outrunner lasts longer as it cools itself
THANKYOU.
Iv just brought this shark esc on my motor iv got red black and yellow wire on esc there all black lol does it matter wot one goes where iv not tried it yet as I don’t wanna blow out
Plug the 2 middle wires together the 2 outside wires don't really matter which one you plug in to one another. The 2 outside wires change the motor direction. Hope this helps
@@IRONCLADRC Errm so two out side wires are red/black and middle wire is signal then yeah ? Think that’s wot I’m getting from your reply ? As you mentioned 2 middle wires and 2 outside but there’s only 3 in total
Do they make racer star outrunners in something suitable for 6s?? Could be a not bad little upgrade from the stock SR80 motor (1750kv)
Offshoreelectrics.com has leopard outrunner motors I think there 6s. Aquastar has an outrunner motor as well, hard to find!
www.google.com/shopping/product/1/image?q=trex450+upgrade+motor&client=ms-android-uscellular-us-revc&biw=360&bih=672&sxsrf=ALeKk02qPjw9qFC0Yp_tq1DXnEna2vGtqA:1628119479506&sa=X&ved=0ahUKEwj9_f3ywZjyAhVhRzABHQyzBFgQnUAIQQ&prds=cs%3A1%2Ceto%3A17001821010392615322_0%2Cpid%3A17001821010392615322%2Csgro%3Aiv%2Cmvi%3A0
Can 30 amp esc support 4000 kv brushless motor
I ran the rocket 2968 4000kv with a dynimite 30a and the Temps were warm/hot
Woa sir can i have like that combo ztw ang 2845 motor