Ender 5 Plus Ultimate Upgrade! BIGTREETECH 32bit 1.4 SKR TURBO & BIGTREETECH TFT35 V3.0
ฝัง
- เผยแพร่เมื่อ 19 ก.ย. 2024
- Kay3D and the Skr 1.4 Turbo are no longer around. This video is solely for educational use. As I mention in the description you are following these instructions at your own risk. There have been many people that have followed the video and were successful. Please do not reach out to me to assist with your printer upgrade.
#creality #ender5plus #bigtreetech #Kay3D
Ender 5 Plus Silent Board Upgrade! Plus more!
Welcome to my biggest video yet! This the Ultimate Upgrade to the Ender 5 Plus! This is the full upgrade process from A -Z. I will be using the BigtreeTech 32bit Skr 1.4Turbo & Bigtreetech TFT35 V3.0 Dual Mode Display. I will be walking you through the whole upgrade process from the beginning to the very end! Including how to put your personal logos on the Bigtreetech TFT35 display! Yes! Bear is in the video, he is "Where is Waldo!" Let me know with a timestamp in the comments when you see him!
BigtreeTech 32bit Skr 1.4Turbo
www.biqu.equip...
BigtreeTech TFT35
www.biqu.equip...
Birgtreetech TMC2208 V3.0
www.biqu.equip...
TH3Dstudio Board diagram
www.th3dstudio...
SD Card extension
www.amazon.com...
Display mount
www.thingivers...
Board Mount
www.thingivers...
GitHub - Configured Firmware
github.com/tri...
Visual Studio Code
code.visualstu...
Cheetah Firmware Kay3D
kay3d.com/page...
Kay3D Facebook group
/ 712547579277208
Jump to parts of the video
Intro -
4:11 Bigtreetech board information
8:45 Bigtreetech display information
11:03 Adding TMC2208 drivers
11:39 Removing parts from electronics box
14:12 Wiring
15:08 Wiring photos
15:46 Cutting the electronics box
17:38 Visual Studio Code install and configure
18:31 Cheetah\Marlin download
20:29 Cheetah\Marlin configuration
40:46 Finalizing wiring including the display
49:02 Flash update BTT 3.5 display and update logos
59:57 Test prints
1:01:07 Print comparison
1:07:56 Final Thoughts and Review
Thanks for watching!
Harbor Freight workbench -www.harborfrei....
Disclaimer - This is an instructional video only - I assume no responsibility if you do not become a pro after watching this video. This video is for learning purposes only, you are following the steps in this video at your own risk!
/ tripodsgarage
/ tripodsgarage
/ tripodsgarage
Thanks for watching - Please Like and Subscribe!
Tags
BTT SKR V1.4 & SKR V1.4, 32-Bit Control Board, BIGTREETECH TFT35 V3.0 Display- Two Working Modes, Silent board, TMC2208, BIGTREETECH TMC2100 TMC2208 V3.0 TMC2130 V3.0 Stepper Motor Driver, 3D Printer, 3D Printing, Bigtreetech 32bit 1.4 Skr Turbo, CR-10, CR-10s, Ender 3, Ender 3Pro, Ender 5 Pro, Ender 5, creality silent board, silent board
I just want to say thank you for doing what you do and representing people with disabilities.
So many 3d printer TH-cam videos are so fast paced and marketed to a very narrow group of people to make money.
The people making these videos do not seem to understand usability and plain language, or understand what it is like to have a disability and daily challenges that they have to navigate in everything they do.
You are a role model for kids with disabilities and thanks for making things accessible. We would not have gotten an ender 5 plus or attempted upgrades without seeing your work.
Thanks Gdesign! You have no idea how much I truly appreciate your comment! I was in tears reading it. I work over 60hrs a week at my main job, and do TH-cam on the side. Even if I can help one person, I consider this channel a success. I hope that I can inspire more people with disabilities, no matter what kind of disability they have.
I have taken more of a streamlined approach in the last 6+ months with my videos. Trying to be even clearer with my approach. I haven’t been on camera much. However, I will be soon. I have another Garage Makeover video coming out, Phase 5, with more ladder time! Yikes! People like you keep me motivated to make more content.
Thanks again for your continued support!
Tripod
@@TripodsGarage I've been using your videos to update/upgrade my Ender 5 plus. Thank you! Especially for the help with the firmware! I spend HOURS messing with that before trying your suggestion, which was the only way I was able to successfully compile.
I did the exact same upgrade to my Ender 5 in had the reference your video about 10 times. You help out a lot. Thank you!
That is great! How is the upgrade working out?
@@TripodsGarage wellllllllllll. I am running the tft50 and trying to get bltouch working which I think does now lol. Plus the motherboard fan doesn't fit in the stock Ender 5 location, so more cutting! . This is my first major upgrade with the 1.4 turbo and tmc2209s. No sensorless. It has been a challenge but have learned a lot. Many issue but getting close
Kay3D's Cheetah is very cool and took a lot of my headaches away. The instructions on the website are a gold standard of clarity.
Awesome video. I put the creality silent board in my printer about 2-3 months ago without knowing it was very limited. Your video went over so much I'm definitely gonna be switching out to this one now.
SupermanKal718 - Thanks for the positive feedback! Hope this helps out a bunch of people out there. Best thing about it, now the bed stays heated if your filament runs out 😁. I really didn’t know how to break this down into multiple videos, so I just went all in 😉!
OK young man, you just convinced me to place an order for a new board and display. I'm sure I will be commenting more after it arrives and I start my installation. Thank you for the video.
Awesome! Glad the video was helpful. And I will be here if you have any questions!
Thanks for watching and subscribing - Tripod
I tuned the serious vibration on the diagonal runs, Cable tied two VW polo exhaust rubber hangers on to the two 20x20 upper cross bars. They are heavy dense rubber, the weight and density silence the resonance. But the Hotend fan still rattles during the vibes.. heavy duty foam on the base rails shut it up too, as does the cabinet enclosure its now in. 24hrs a day no longer a problem.
Great video, I'm the designer of the 2 brackets you used for the SKR and the TFT35, just wanted to say its great seeing them in use, and others getting some value from them. I found your video because I'm about to replace my 1.3 with the 1.4 turbo.
M C - Great work! They are a perfect fit, as you can see! So happy you found the video, hopefully it comes to good use for your upgrade. Thanks again - and thanks for watching! Tripod
Hi, do you have a file for the TFT35 v2? I got a SRK1.4 i want to swap and it was a combo deal with the V2 but the file is for a v3 which is a bit different dimension. Eitherway, great work. They printed great
@@0xFAVS Hello! I do not have a file for the TFT V2, so sorry! I was on the BTT site and all I can find is the Bootloader. Seems that all the Github downloads are gone for the TFT35 V2.0. I will continue to look! Thanks again for watching! - Tripod
@@0xFAVS I don't, I only own the v3, I measured it up with a set of calipers. If you want to adjust the design yourself I've included .step files on the thingiverse page. These are easy to edit (compared to .stl) in something like Fusion360.
@@0xFAVS I found a diagram with measurements for the v2, I will have a go at editing a design for the v2 when I have some time later tonight, but you will have to print and test it, because I don't have one to try it with.
Brilliant ! This has made the process Sooo much clearer.
You go thru the detail steps.. Including what Files and Tabs to click on.
Few other videos even bother. Most gloss over that level of detail.
I find it Very important , critical Info... for us Newbies.
Thank you !
John, Great video!! I can see why it took you a while to put this together. The advantage of this upgrade is the extra features and options you gained. After watching the video and your fun with the control box, you can understand why I ditched the box and made a new mount.
Hello David!
Yeah, this video took me a really long time to put together! This video could have been easily 2 hours, I cut out a lot of footage. I might have to do a long term update. I stared at the box for a long time deliberating if I was going to keep it. I decided for this upgrade, I was going to keep the stock look. The box is getting crammed, but I kept it neat and tidy. As for future updates, we shall see if it remains! Yes, extra features and functions is correct, plus some future expandability. It is so nice to have the filament runout working correctly and leaving the bed heated on! I really dig the dual displays, I learned a lot making this video, diving into stuff I never did before. I hope that this video is useful to others as well.. Thanks again for watching!
@@TripodsGarage At this point there's very little Cheetah left in your setup ;)
Working advanced pause/M600 (filament out) -> multi color printing made easy! :)
As i have stated in an email to you, your TH-cam videos are a huge resource and help. Thanks and keep up the good work.
Oh! Email? I will have to check! My apologies, I get so many and work a full time jobs as well. Thanks for the compliment, much appreciated 👍
Hi John this is great job! I have receive my upgrade kit (skr 1,4 turbo with tft 3,5 v3) 4 months ago- on the 4 day of testing the tft shorted down so the board! So waiting for new one :))))
This is great thanks :) So many things are covered.
Maybe I missed it but one of the issues I had and solved was that the build environment was not set. Without this the build fails right after beginning compile. To fix I just changed default_envs = LPC1769 in the platformio.ini file. Thank you so much for the wonderful video.
I used this for my Ender 3 Pro, but the Cheetah would not even compile. VS Code indicated that the INCLUDE folder was missing. DLed the Cheetah from both their site and from Github using the links in the Cheetah site. One DLed Cheetah, the other directed me to Marlin, no Cheetah. Cheetah would not compile and the second is that standard drone of completely modifying the code in Marlin, which I did before and didn’t work correctly.....when I did, I always get the NO PRINTER ATTACHED, and I have been unable to resolve.
One thing that helps when cutting out your new slots is to drill out the corners first. If you want to keep your cuts straight you can take a straight edge to the case and rest the cutting wheel on that while cutting. Appreciate your video, I just ordered that board because of it. I chose the HRP-600 power supply though.
Something else I will add, I trimmed the reset button off flush to the bracket on the tft35, put some masking tape around it and hit it with a dremel. Its just too easy to bump mid print where it is.
This saved me so much time. I put in an SKR Mini E3 v2.0 board but the changes were pretty straightforward. One thing to point out with the current version of Cheeta enabling the EMERGENCY_PARSER caused the compile to fail. So I took it out and at that point, everything worked. Again thanks so much this is a really great video. Much appreciated.
Awesome job. 32bit turbo. Well done.
Turbooooooooo!
what is your next upgrade?
Not only is the silent board not upgradeable, the stepper drivers are in standalone mode so no software config of them.
VERY GOOD VIDEO! I am impressed, excited and can not wait to finally have my setup completed! THANK YOU!!!
@Mr Day - Thanks for watching, and thanks for the complements 😀! I am happy to be part of your future upgrades!
Thank you, I broke my silent board USB, and Creality didn't (still doesn't) currently ship to the UK. So I found this on alternative control boards, and it was very helpful! I have ended up using Klipper firmware, I'm happy with the results. Though I should say Klipper doesn't support the TFT35 currently (12864 emulation mode is lacking a feature that Klipper uses, apparently).
Thanks for watching! I will need to look that up! Thank you...
Great Video!!! Thanks a lot. your final comments are right on spot. Now my final caveat is why Creality does not offer this printer already with a 32 bit board with silent drivers, I´d grab one right away if they do. I can tinker this one for sure, I did the same for my tow E3s, but honestly, too much pain.
Oh!!! Btw... tomorrow is the planned re-release of the Ender 6 CoreXY, maybe that is the reason why, to avoid cannibalizing. If it convinces me, I´ll get it, if it does not, I´ll get the % Plus and upgrade it.
Love the videos, after watching you videos on upgrading the 5+ I have everything ordered and going to replace everything now. It's not a matter of if something will go bad but when. Thanks for the video, I've been binge watching your channel
Wow Tripod! That was one complete build! You really did go from A to Z! With this instructional video, it will definitely make it a lot easier for others to do this, without having to wait 4 videos to complete it. I totally agree the Creality board is just a waste of money. I heard that Creality’s new lineup of printers still do not have a 32bit board. If you are going to pay north of $300, a 32bit board should be standard, with upgradable drivers. I believe that companies like Creality are veering away from open source and not releasing the firmware on purpose, to lock down their printers. This way they get less questions about non-approved Creality upgrades. Just my two pennies! How long have they promised the Ender 5 Plus firmware\config? Their new lineup looks of printers all have a custom UI touchscreen... Thanks again for another amazing video!
Great stuff man, ive watched this a few times now in preparation for my board! Gets here Tomorrow!
Thank you so much. Great detail video. I have an Ender 5 and the Ender 5 + and you just convinced me to get that board and I will go with the original Marlin as I am a little familiar with. I like the stock LCD but it will go away. Glad that you have the E5+ and I will be looking forward to see other vdeo.
Thank you for this walk-through! Very helpful hints on configuring the firmware!!
Visual studio? That looks like a pain to use. Why not just use arduino software? It's simple
KornShaDoW097 - Use what software you feel comfortable with, Visual Studio is what I choose to use.
Tripod, thanks so much for making this video. I followed it (I think pretty carefully). My only difference is that I used the 2209 drivers (and snipped the required pin). I upgraded both the SKR board's firmware using the Cheetah using your instructions in the video, and the TFT display board using their github repo. My only problem after everything is done is with the BLtouch. I think I have my BLtouch wired (I think) exactly like you show, in the Servos/Probe receptacles (rather than the Z-stop probe that Kris Kersey showed in his video). I figured that would ensure that the firmware is configured for the BLT correctly. The only diff (and challenge) is that my cable is white/black/orange/red/brown. I think that matches yours (white/black/yellow/red/blue). However, when I try to Z-home, the probe extends and retracts a couple times, then flashes red and I get an error on the display saying I have to reset with an M999. I would be very grateful for any suggestions you might have for troubleshooting this one last issue.
Waiting on my set, thx for sharing all your work 👍
As an option for those wanting to save the money on changing the screen out: You can use the stock Creality Touch Screen with the SKR V1.4 using the TFT pin header on the board. I've done this on the CR-10S Pro and the Ender 5 Plus appears to use the exact same touch screen. I pulled together some info for the pinout on the Creality Touch Screen and someone else tried it before I received all my parts to complete my upgrade and they confirmed it worked. I finished my upgrade and was able to get my stock touch screen to work on it. I hope this helps someone else wanting to use the stock touch screen instead of replacing it: imgur.com/gallery/rcrRf0u and imgur.com/kanEegg
I'm not being critical of you replacing it. Totally a cool option. I share this only because it was hard for me to find the info at first. I saw someone say it could be done because they had done it, but I needed to see exactly how. Well, I figured it out again (totally not the first person to do so), but maybe that info above will help someone else. It was really nice to be able to just change the pins and connector on one end of the factory cable and plug it straight into the SKR board and have it work.
Thank you very much for putting this guide together. I'm saving it for when I go to upgrade the Ender 5 Plus. Cheers!
BTW, @tripodsgarge all the other videos were confusing you showing us the cheetah method very helpful. I was abe to get my ender 3 going with your video. THANKYOU . Perfect video, A+ 100
Hello FPV trys! That is amazing! Gland I was able to help even if it wasn't and E5+!
Thanks for watching -Tripod
Yup. This vid is THE thing that made me realise I can configure the thing. Time to build my "Ender 50 Plus/2" ...just an E5+ clone with a 1200 mm X and 800mm Y. 500°C nozzle, 120°C bed and 300mm/s here we come... :)
Since you published this video, there is a newer release of Cheetah. Also, there is a remark in configuration.h, line 302 in the newer release, shows this:
#define FILAMENT_RUNOUT_SENSOR // Define this if you have a filament sensor. Please ensure it is connected to your mainboard and NOT your TFT
//#define INVERT_FS_LOGIC // Define this ONLY if filament sensor is not detecting filament correctly.
Have you tried the INVERT_FS_LOGIC setting ?
As to your remark about "when the source is released", it is all in the distributed files. You might not be recognizing the code, as much of the menu code is heavily wrapped in various macro definitions.
As an aside, the line numbering has changed somewhat, from what you mention, to the current release, anywhere from 2 to 32 lines, depending on how far down the configuration.h file you get... but a little hunting around will turn up the desired lines. One also needs to set the "default_envs=" parameter in the platformio.ini file, about line 22. Using the turbo 1.4, I used default_envs = LPC1769
This last definition is explained in the KAY3d Labs video th-cam.com/video/G5Yn_wPlrQs/w-d-xo.html
If it was shown here, I just missed it.
key3d site dosent work im struggling to get my printer off the ground using BTT SKR V1.4 TURBO
Can’t wait to see what amazing prints you’ll come up with. Keep up the awesomeness ! Stay safe. Subbed!
dutchcruise - Thanks Dutchcruise!
I got TMC5160s and keep getting all high and kill halt.....keep going back to the drawing board.... Real headscratcher getting this to work, oh well, upwards and onwards! Without this vid, I wouldn’t be as far as I am now, so thanks again.
Nowadays it would be just so simple and cheap to connect a laptop or tablet with the right software/app and controll the machine with it. I am wondering why is so necessary to hassle with all these
What kind of tmc2208 did you get? I see DIY, uart, step?
I recall you can set that on the MB but the driver it's self? I get uart but what are the other 2?
Also did you get 4 or 5 set of drivers? I know some people have always used other stuff for the extruder.
I tried using a different extruder driver for my tevo tarantula and it was noisy and I didn't see a real difference.... Not good ones... Just issues.
KornShaDoW097 - 5 TMC2208’s are included in the kit. You can use 5th one for the dual Z or for another extruder.
I just came across this video because I had searched for SKR 1.4. Good comprehensive video. Did you ever fix the runout sensor problem? you need to either plug it into the tft and try it or rem out the lines in the touchscreen firmware. You have the SKR looking for filament switch input at two different places. I know it works in one and not the other. Just try switching the sensor from the board to the screen. You had another problem too, with a similar solution, I dont remember what it was.
love the video the disabled can do all well done my friend
you sir are a life saver! you saved me with this code!
I put a BTT Mini skr E3 v3 in my Ender 3 pro. The only noise is from the fans. I used the same display you used
I wonder if the touch ui expects the filament out sensor to be connected directly to the LCD while the marlin mode uses the firmware handling of it?
First video of yours I've watched, somehow, but awesome walkthrough thank you! Subbed.
Not sure cheetah is ready for prime time. It is a great concept but there are errors in the files. Even the platformio has a path error. So much time debugging it may be better to get vanilla marlin and start from scratch.
thanks for your video! one of the best tutorials on youtube. I got everything working except for the bltouch, the bed doesn't want to 'come up' to reach the probe. will try some more tomorrow!
Did you figure this out?
39:33 The .pio file is not in the configured firmware you posted on your Github
It is the same file, just uploaded one right to the first page. Instead of having to drill through the folders.
The sourcode is out, i got it 18.march, but that doesnt help for the display, that is a properitary unit, and no sourcecode available. So, anyway, good idea to remove it, it was totally useless display anyway.
The display just lack a lot of the common Marlin features. Best decision for me was to swap it out!
Kay3D site doesn’t seem to be up anymore, can’t access the files, followed this guide ~1,5 years ago and having trouble with babystepping only going in one direction. And ABL seems to get different results every time.. anyone experienced this?
Great Video! Subbed and liked! Content was so helpful keep it Up!!!
Thanks for this bud.. long but really educational..
What does LCD12864 setting "Change Media" do? Thank YOU 2000%
I'm installing the SKR V1.4 turbo on a stander ender 5 great info thanks
Check out the Lerdge K board very comparable to this board and better. I installed it on my Ender 5 plus. No need compiling codes and I can change setting via the GUI on the fly. Very good details features setting.
I’m having the hardest time trying to get firmware installed kay3d doesn’t seem to exist anymore
I hate to ask this on a 3 year video but can you please update the links for the wire for wire diagram. I'm getting lost 😔
I have everything set up, ran a couple quick test prints and now I have embarked on a 40 hour print. I will let you know how it goes
Awesome! Congrats on your new setup!
Great video! Couple of questions:
-will this be as silent as the silentboard from Creality?
-What is the difference between 2208_step and 2208_UART?
Hello there
I watched the video, and thank you for this for this detail. I have an ender 5 plus. I love it, but I am having these small issues here and there, and I'm leaning towards the stock board 8-bit and the firmware that comes with it. Also, their slicer creality 4.8.. I have been going over and over on videos to try to make sense if I do need to swap the stick stuff out and lean towards the better stuff. Upgrades I have done: exoslide, Capricorn Tubing, the silicone swap of the srings for the bed for leveling works great, by the way. My question to you on the video you presented on this upgrade. Did this make the printer work better for you? I'm only looking for the better upgrades as being a hobbyist only and my next project that I want to do is print out a gaming board and want to make sure that I get a really great detailed print for this. Thanks in advance for the update.
Im looking to do this upgrade on my 5 plus and your video I find the most easy to follow. Tons of information and I love the dogs!. That said on BigTrees site there are 2 different 2208 drivers. 3.0 step or 3.0 UART. Which ones did you use? Thanks so Much!!! Keep pumping out the great vids.
Hello Joshua - Thanks for the compliment and watching my video! This is what I purchased. BigtreeTech Direct SKR V1.4 Turbo Control Board + 5pcsTMC2208 V3.0 UART Mode Driver. Hope that answers your question? Thanks again!
You picked the best firmware. Cheetah is amazing
You indicate that you have the SKR v1.4 Turbo yet you have configured for the LPC1768 which is the SKR v1.4. The LPC1769 should have been configured instead. Obviously, you have it functioning via LPC1768, but I'm curious if you are limited to 100MHz processing (speed of the LPC1768). The processing speed is the sole difference between the LPC1768 and LPC1769 which is likely the only reason it is working for you. I suspect you're not taking advantage of the LPC1769 turbo processor which runs at 120MHz. Can you confirm?
Great video, thanks!
Any reasons why you didn't choose the TMC2209 drivers instead of the TMC2208?
Hello Mischa - I was comparing it to the Creality silent board, which has TMC2208’s. Thanks again for watching - Tripod
Okay, then I understand. Do you see any problems when I'm going to use TMC2209 with this setup? Any special steps with the firmware (besides just changing the regarding lines) or with the jumpering?
@@mischaanwald 2209's (At least bigtreetechs version) will have the diag pin soldered to the stepper stick. This pin needs to bent/lifted/cut in order for mechanical endstops to work properly (keep it to use sensorless homing, that's the only thing it's for). Other than that and defining 2209 instead of 2208 there's no difference.
Hey man! Great video! Sorry it took me so long to respond but I made it through it. Congrats on the killer setup.
Thanks!
No worries, I figured you were extremely busy! We can try to do a collaboration another time, maybe when all this self quarantine blows over? This way we can take our time, and schedule times to meet. The printer has been absolutely solid since the upgrade, been running almost 24/7 for 2 weeks straight. Thanks again!
Amazing tutorial thanks Tripod, all working except Filament Sensor. I think from your wiring picture its correct and I defined the 2 additional lines in the file line 296 / 297. There are settings in the LCD smart off and on, so far I have just disabled it, did you have any issues? can you blow up the pic to confirm its cabled correctly please? thanks!
It *may be possible* to print directly from the SD Card on the Bigtree Tech board *Configuration_adv.h*
I can't test this because of bugs in Malin code
// Add an optimized binary file transfer mode, initiated with 'M28 B1'
//#define BINARY_FILE_TRANSFER
/**
* Set this option to one of the following (or the board's defaults apply):
*
* LCD - Use the SD drive in the external LCD controller.
* ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
* CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
*
* :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
*/
//#define SDCARD_CONNECTION LCD
#if ENABLED(SDCARD_BOARD_FIX)
#define SDCARD_CONNECTION ONBOARD // Forces SD card to work on mainboard. Some boards do not need this fix.
#endif
#if ENABLED(SDCARD_LCD_FIX)
#define SDCARD_CONNECTION LCD // Forces SD card to work on external LCD/ TFT. Some screens do not need this fix.
#endif
I used your Firmware and my extruder will not move at all. it moves when i try the y stepper cable i even tried moving the e stepper connection down one slot. any ideas? I have TMC2209 and I feel like ive tried everything except compiling my own firmware. Thanks for the fantastic video its what got me this far..... and im sooo close... but yet so far. someone please any suggestions. THNX
Awesome video. I'm looking to get into 3d printing and my choice so far has been between the Ender 5 plus or Ender 3 Pro. I've been looking into what would be good upgrades to do to the machine. I've seen the SKR mentioned for E3 but till I saw your video I've seen no mention for E5+.
U2Ra Mess - Thanks for watching! There are plenty of upgrades for both printers. The Ender 5 Plus was my first 3D printer. I was sold when I saw build volume of the E5+! I didn’t see any videos either using a Skr board in a E5+, so I decided to tackle it 😉. I love the 3D printing hobby, starting to design my own parts for our atv’s and other things! Again thanks for watching- Tripod
Prusa has owned the 8-bit processor, look at all the functionality on the MK IIIs, this is all down to clever programming and optimisation of the firmware, there is more functionality on their Rambo than a lot of the 32-bit offerings
I ordered this board 17. march, but still not got it, very slow shipping from biqo (lot of other stuff ordered later from china have arrived)
Sorry to hear 😞. Hope it arrives soon!
I am just about to do this. Thank you so much for putting this video together
Awesome! Hope everything works out! Thanks for watching - Tripod
Tripods Garage I am just going to use your firmware build as I have everything as you do
Dave Glover - Perfect! Remember you can always change the name of the printer 😉
@@TripodsGarage I got everything Wired up tonight. Now I just need to cut the case to make sure everything is accessible. I did do a test homing and a z-offset as well as heatbed and hotend. Everything seems to be working perfectly. Thanks for putting this together!!
Dave Glover - awesomeness! If you haven’t cut the case yet. There is another file on Thingiverse that has the Skr board mount that turns towards the PSU, however you will still need extensions. Thanks again for watching - Tripod
the touchscreen has a filament runout sensor port of its own and will only work when it is hooked up to the touchscreen and the print running from the sd or usb port of the touchscreen
Nice job thanks
Can't you just use a tft35 e3 version 3 and not have to print a mount or use a dremel for the notch?
KornShaDoW097 - Your choice, mount it wherever you want.
@@TripodsGarage do you know if the e3 version matches the holes, so I don't require a mount and fits the enclosure? I'm guessing I'd need to drill a hole for the knob. Instead of trimming with the non e3... N hopefully it fits?..
What am I doing wrong I put in the SD card with your get hub file, booted it up and it did nothing far as a update that I can tell? I have the exact same parts as you.
Marcus Carter - Make sure the card is formatted in FAT32.
@@TripodsGarage which it is already
You are running your bed way too cool. Need 70-90 on the E5P for consistent bed heat distribution.
Hello! Nice tutorial :) I don't know if something changed recently but I had to undo the P0_10 in the pins file on line 91 to the original value of P1_27 to get this to work for my setup. I was having the exact issues you showed in your video on facebook with the P1_10 set as that pin. Strange but I'm glad it's working now. Thanks again.
Are your BL Touch wires a different colour to his?
I just got my E5+ a couple of weeks ago and it came with the Meanwell PSU already installed and my BL Touch wires are different, so I'm wondering if they corrected their wrong pins mistake...
@@mackinsvii9022 Yes mine are different - and still in the wrong place. I rewired them to be in the correct order. I have the meanwell powersupply as well.
@@IntrepidDawnAhhhh thank you, I was hoping they had fixed it. Are yours in the order of black, white, orange, brown and red? At least before you changed them and what order are they now?
Also, how do you actually change them?
@@mackinsvii9022 I don't remember what they were but I did need to remove all of them and replace them in order with a wiring schematic.
@@IntrepidDawn Can you remember where you found the wiring diagram?
Why make changes for custom printer when it's commented out? 24:42
Hey Thanks this is very nice, its going to bea my next projekt :)
Holy crap, so THIS is the video you meant, LOL! TH-cam notify fails AGAIN!!
Yepperz! Gotta love TH-cam notifications! Let me know your thoughts!
@@TripodsGarage great minds think alike! I fluked onto that Kay3d website somehow, via a core XY printer video, and the 30 minute video they have on Cheetah is *excellent*. To that point, I had not heard of it, but it supports all these mods with the E5P right out of the box it seems. I just need to figure out how to mount the SKR board and a Pi in that cramped case!
@@bartacus3521 Was 3/4 of the way through a Marlin config, then I also stumbled on Kay3d! Thingiverse files are in listed for the SKR mount and Display - well all but the Pi mount (next video?). The person that designed the two parts I used, even commented on the video...
Great video, really enjoyed this. you got a new subscriber.
Carlos Spiceywiener - Thanks for the compliment, and subscribing!
Great guide! After flashing, The touch screen says 'no printer' and the legacy screen says ERR: EEPROM Index I have reset the EEPROM on the printer via the menu, and rebooted. No luck. When compiling, I get YELLOW messages starting after compiling.......Sdfile.cpp.o 'In file included from Marlin\.....trinamic.h:35 and its all yellow after that, but does say Success!
ideas? Im going to start fresh and see what happens.
Fresh install... no errors, 4 'problems' {}c_cpp_properties.json cannot find c:\--------- \ include all 4 errors refrence that. Upload to printer works, however still have ERR: EEPROM Index and the touch screen says 'No printer'
This time I downloaded just the firmware.bin from hub, the EEPROM error went away after i reset it, however touch screen side still says no printer. Changed speed setting to no avail. On legacy side, i selected auto home. Bed moved down a bit and then Printer Halted.
update again.... re downloaded the firmware.bin Played with wires and found the EXP2 for the display needed to be flipped upside down. Which is REALLY odd because BTT lcd and board should be correctly aligned. This firmware works, so I believe it must be a computer issue on my end, when I compile the firmware myself.
As the Cheetah for E5+ is not a BETA anymore, i started preparing the SKR1.4 Turbo + TFT35 2.0 upgrade for my printer. I had to make two more settings, which i didn't see in your video: platformio.ini:
default_envs = LPC1769
Configuration.h:
#define TEMP_SENSOR_0 1
Can you confirm these values are correct?
And thank you for your video, it's a really good starting point!
Yes
Thank you so much Stefan for this information. It would not compile at all until I put in those two settings. Saved me hours of troubleshooting !!!! Great Job
Excellent video! Helped out a lot however I'm not quite done. Im using a Micro Swiss DD set up, how do I enter or select that in the marlin set up? Would i define the "custom extruder" and enter in the E-steps?
You: "I'm an average guy". Me: "Nope, you're a 3D printing BOSS". BTW, before stumbling across your video I was one more afternoon from tossing my ender 5+ in the garbage bin. Thank you.
Thanks! I totally appreciate it!
Go Bears! Even though Im embarrassed to say that haha. From Chicago area I assume? Im downstate!
Yeah I live in Northwest Suburbs of Chicago. Ah go Bears! I tell everyone the Bears are always in a rebuilding season. Well there is always next season 😉
@@TripodsGarage rebuilding since about 09 lol we will get there!
😂😂😂. 100% Correct 👍👆
Click wheels nice but you lost the easy menu navigation of the touchscreen
Well it is a click wheel and touchscreen 🤔
@@TripodsGarage looked like it had too many extra menus and a much smaller screen
Hey! Great video. Working on this myself. Did you have any trouble with the extruder motor making noise? I increased the vref on the stepper and it got rid of most of the high-pitched noise I have (key-word here is most), but overall it still makes quite a bit of noise.
Why do some use uart vs step drivers? (with tmc2208)
Fantastic vid convinced me to go Skr v1.4 turbo. Makes it very easy to install, but, i am not into compelling, and understanding the config, files, i must have missed it where can i find your .bin file or at least one that might work. Please help. I hope your .bin is available
Great helpful video
My stock main board just calved so I'm deciding which one to put in, silent or big tree tech?.....decisions, decisions.....
my board is on the way! thanks, my only question is that you did not enable thermal runaway for either the bed or hotend, is it already enabled?
Thanks for watching! Thermal runaway was already enabled by default. The changes were made specifically for the Ender 5 Plus, plus some tweaks\fixes I noticed along the way. Thanks again for subscribing - Tripod
Thank you!
Hello, I have the exact printer and drivers and I go through video and I have still problem with Z_homing. It only goes down, not up to BLtouch. Could you have an idea for it or it is more difficult to explain?
NEO to the the rescue
This is great and exactly what I needed for my ender 5 plus, I got the SKR 1.4 turbo and a TFT70 yours was the only firmware that worked after trying others The only exception I'm having is the BL touch. It's not responding I see a little flashing red coming from it but not the full red glow like before or even actuating at power up. I did the reorientation of the servo wires Brown Orange red, but maybe have damaged it I don't know if so maybe I'll have to order another?
Got it squared away, twas the Blttouch wiring, turns out the original way was correct. But now it's printing in the friggin air!!! Any idea why?
Ordered the boards and screens from the link in the description, 2 for Ender 3 and 1 for my Ender 5plus, It's been 6 weeks and they still haven't even left China. I may get them by xmas.
Thanks for watching! Unfortunately there are big delays on receiving goods from China. I wanted to do a review on the BTT Skr Mini E3 V2.0. I ordered a BTT Skr Mini E3 V2.0, took over 2 months to receive. Hope you get them soon!
I ordered from the link and didn't hear from them, so I ordered off amazon and got them within 2 weeks, then about 2 weeks later the other order showed up.
I have an Ender 4, which lost the z for the bed. I purchased the same board and screen that you did. Do you know if I should use the firmware for the Ender 4 or would the Ender 5 work. The Ender 4 looks just like the Ender 5 but it is 3 years old. Creality said the original board won't accept the new firmware and told me I should just buy a new printer. They won't respond to any of my emails for information on how to proceed. Thanks for the video!!
Thanks!
Thanks Daniel, hope this video was useful! Thanks for watching!
23:25 Why would you not select the TFT35 graphics display option? It says to select that if you are using BTT TFT screens