Very helpful, am building my own floor standing speakers, with 4 (6 1/2) bas/midle tone speakers. Thank you for showing how to connect them in the right way, to get 8 ohm in total.
Or should i just put 2 midbass in series and let the added cone area add + 3 db? And -3db from the increased impendance ? Or are my calculations wrong?
Those drivers look very very similar to Visaton FRS8 drivers. For better off axis response I'd recommend a horizontally curved front baffle and putting the tweeter up higher then the mid drivers. This should reduce the beaming effect you get from the current design.
Dang fine piece of functional furniture ya built there! I don't need to know how to use power tools or build a box. I need to know how to wire up a diy bass guitar cabinet with a horn and crossover to push air at 4Ω Imma go out on a limb here and assume that the size and power and impedance is somewhat irrelevant as long as your target impedance can be met by the wiring. This is basically the same as if I were to build a 4x10 with horn and crossover for a bass guitar cabinet 4Ω at the point of power. Right? Dang! That you drumming? That's my gig but I wanna slap de bass also!
@@chrclmnky seriously. since daddy peavey retired they don't hardly answer the phone anymore. imma do this on my cab. drivers on the way. i'd jam with you any day homie. I ran this vid thru my PA and it's the shit!
Get drok speakers, they are better... put the bass port where the Tweeter is... put the Tweeter on top or below it, if that makes sense. But either way have the bass port facing with it ( gives a little extra thump). and use MDF next time. Other than that I have to say it looks good!
Is it on a center channel on the receiver or a left/right? I know it a center sound bar I built on similar but have it 2on left and 2on right no center tweeter just 4- 6 1/2" coaxial speakers on a L/R 2 channel amp great job though 👍
Thanks Jonathan. This speaker can be re-wired for a left and right configuration but the tweeter can be only on left or right. You can build something similar and install two tweeters for a more flexible speaker feature.
Brother Coaxial speaker me apni choice ke hisab se 12-15 wattage wale tweeter lgwna chahta hu too worth rhega car me music system ke liye yafir koi fayda nhi Lagwane ka
It probably sounds just fine, but I never liked those plastic tweeters. I like metallic domes the most, but they can be a bit expensive. These are okay if you are on a budget. The mid-woofers actually look good.
4400hz has a wavelenght of 7.8cm or roughly 3.1". Considering your drivers are 3" in diameter and also spaced out a bit there is no way they are within 1 wavelenght center to center at the crossover frequency. This will cause intermodulation isseus with peaks and nulls as you move around. You need to cross overa lot lower for this and most likely second order unless your tweeter has a very low self resonant frequency (like below 1k at minimum). I also doubt bass reflex does much good with 4 drivers in that box. What frequency did you tune for? Might be better of closed, and braced. Also 4 horizontal drivers create a line array which will cause beaming and a narrow sweetspot with your tweeter beaming in the middle. You can improve this with a series lowpass over the 2 outside driver (I'd suggest first order at 300hz,all you need is 2 caps) Whenever possible install the tweeter above the center of the other speakers in a center channel. This will give you a much better high frequency dispersion. Good luck 😉
Nice sound sir, I hv a doubt, what is the software u r using for box design and what is that 4400 HZ frequency ur using...and also u didn't show the back side connections of cross-over ckt..
Very nice presentation sir, Need your advice ano sir magandang subwoofer for my drums and bass? my top ako na power HH 500 watts hindi ko pa makuha yung magandang tunog ng drums. Sana po sir may pwede ka isuggest sa akin. Thanks for the video dagdag kaalaman.
In diagram you have in video. Green line (wire) connect with speaker's +terminal on left side but on the right side same wire is connected with - terminal of speakers. I dont get understand? Kindly guide Thanks
Your calculation for the low pass (woofer) is wrong as you have connected four 8 ohms woofers in parallel. So the effective impedance will be 2 ohms for the inductor calculation.
Sir ano po ang total wattage at total impedance ng dalawang 300 watts at dalawang 150 watts tweeter Isang midrange 150 watts 8 ohms po lahat at may dividing network na 600 watts..
What types of speaker are best for diy boombox ? I allready have 4pis 4inc 40w(aes) woofer and i use those all 4 and now what's i need like subwoofer tweeters and quantity.?
It all depends, I wouldn't say it's high at all considering the drivers. Small midrange or fullrange speakers can play well over the crossover seen here and small tweeters can't play very low.
Outstanding! Thank you for showing this. I am just about to finish up my truck and I was thinking about a center speaker somewhere in the dash. BTY, how did your plywood box turn out?
Yes I believe you are in a country that has aplenty of available electronic goods. Here in the Philippines so rare to find such, so I ended up DIY'ingn them.
Hello Surendra, you need to purchase a Bluetooth/digital module and connect it to your amplifier. There are many of amplifiers that already has Bluetooth and digital input/output. I hope you can find them.
4 drivers ..one port? not even centralized?? the air from the furthest drivers .......oh dear ...someone didn't think why they put two ports in 4/5/6 driver arrays lol
Sounds great Sir :) i just saw the video that you've been here in Iloilo City, 2 weeks ago Sir 😅 nandito ka pa rin po ba sa Iloilo? o bumalik kna po sa Butuan City?
Sir i want to make 5.1 home theater with good base.please can u tell me all spare part which are required like woofer ,speakers,tweeters,board.i want to use like home theater.directly connect to plug board in home.if u tell me i will go to electrician to connect them.please tell me sir
Very helpful, am building my own floor standing speakers, with 4 (6 1/2) bas/midle tone speakers.
Thank you for showing how to connect them in the right way, to get 8 ohm in total.
very awesome im trying to make a speaker for my engineering class this is a good resource!
Anup Sastry \../
I was thinking what you gonna play as a demo, perfect choice
This guy rocks!
Next level sound clarity..❤️❤️
😎🥳
omg thank you for showing that 4 midbass desing :D i was just thinking how to make center speaker with the same impedance as my front speakers :D
for some reason i was only thinking 2 midbass desing :D
Or should i just put 2 midbass in series and let the added cone area add + 3 db? And -3db from the increased impendance ? Or are my calculations wrong?
Those drivers look very very similar to Visaton FRS8 drivers. For better off axis response I'd recommend a horizontally curved front baffle and putting the tweeter up higher then the mid drivers. This should reduce the beaming effect you get from the current design.
Nice build Sir. Planning to do this later. Keep it up
Cool, thanks
ganda ng tunog solid na solid kahit maliit lng buong buo
Dang fine piece of functional furniture ya built there!
I don't need to know how to use power tools or build a box. I need to know how to wire up a diy bass guitar cabinet with a horn and crossover to push air at 4Ω
Imma go out on a limb here and assume that the size and power and impedance is somewhat irrelevant as long as your target impedance can be met by the wiring. This is basically the same as if I were to build a 4x10 with horn and crossover for a bass guitar cabinet 4Ω at the point of power. Right?
Dang! That you drumming? That's my gig but I wanna slap de bass also!
😎
@@chrclmnky seriously. since daddy peavey retired they don't hardly answer the phone anymore. imma do this on my cab. drivers on the way. i'd jam with you any day homie. I ran this vid thru my PA and it's the shit!
Eu também construo minhas próprias caixas para meu Receiver 7.2 ... excelente trabalho de restauração parabéns !
Get drok speakers, they are better... put the bass port where the Tweeter is... put the Tweeter on top or below it, if that makes sense. But either way have the bass port facing with it ( gives a little extra thump). and use MDF next time.
Other than that I have to say it looks good!
Yes sir thank you.
te quedo maravilloso, por como diseñaste el cajón se ha de escuchar muy nítido el audio... felicidades te quedaron increíbles
Thanks. 😊
ganda neto boss sana madali lng gawin yang crossover
Is it on a center channel on the receiver or a left/right? I know it a center sound bar I built on similar but have it 2on left and 2on right no center tweeter just 4- 6 1/2" coaxial speakers on a L/R 2 channel amp great job though 👍
Thanks Jonathan. This speaker can be re-wired for a left and right configuration but the tweeter can be only on left or right. You can build something similar and install two tweeters for a more flexible speaker feature.
Nice build man. Sounds great.
Thanks Chris.
Brother Coaxial speaker me apni choice ke hisab se 12-15 wattage wale tweeter lgwna chahta hu too worth rhega car me music system ke liye yafir koi fayda nhi Lagwane ka
It probably sounds just fine, but I never liked those plastic tweeters. I like metallic domes the most, but they can be a bit expensive. These are okay if you are on a budget. The mid-woofers actually look good.
Yes sir thanks very much for the feedback. Newbies like me still have a lot to learn. 🤓
4400hz has a wavelenght of 7.8cm or roughly 3.1". Considering your drivers are 3" in diameter and also spaced out a bit there is no way they are within 1 wavelenght center to center at the crossover frequency. This will cause intermodulation isseus with peaks and nulls as you move around. You need to cross overa lot lower for this and most likely second order unless your tweeter has a very low self resonant frequency (like below 1k at minimum). I also doubt bass reflex does much good with 4 drivers in that box. What frequency did you tune for? Might be better of closed, and braced. Also 4 horizontal drivers create a line array which will cause beaming and a narrow sweetspot with your tweeter beaming in the middle. You can improve this with a series lowpass over the 2 outside driver (I'd suggest first order at 300hz,all you need is 2 caps) Whenever possible install the tweeter above the center of the other speakers in a center channel. This will give you a much better high frequency dispersion. Good luck 😉
Nice. I appreciate the feedback. Will do. Thanks.
Another great job CM👍
Thanks Andy
Here's you was use MDF so sounds is awesome after all
Nice sound sir, I hv a doubt, what is the software u r using for box design and what is that 4400 HZ frequency ur using...and also u didn't show the back side connections of cross-over ckt..
Hello Nandu. Sorry for the limited information about this project. Just use crossover calculators when you build your projects.
Very nice presentation sir, Need your advice ano sir magandang subwoofer for my drums and bass? my top ako na power HH 500 watts hindi ko pa makuha yung magandang tunog ng drums. Sana po sir may pwede ka isuggest sa akin. Thanks for the video dagdag kaalaman.
Solid naman po idolo .. how much po kaya magpa build sa inyo ng ganyan??
Thanks. Meron ako gawa yung white automotive finish, for sale ko. Check nyo video sa channel.
sna yung sunod mong build is 2 way tower speaker nmn with 3pcs 8 inch driver and a tweeter.. heheh.. looking forward for your nxt project sir
Yes sir. Medyo mahal din puhunan gumawa ng tower speakers. :) But will try to save up for those. :) Thank you for dropping by.
nice drum solo
yes, dude's a beast
In diagram you have in video. Green line (wire) connect with speaker's +terminal on left side but on the right side same wire is connected with - terminal of speakers. I dont get understand?
Kindly guide
Thanks
o really luv ur work u upload
thank you 😁
You can use any song here for better your speakers
Verry good gaming station
Magnífico trabajo compañero...enhorabuena.....
нормальная система , а кто был Ваш помощник на четырёх ногах ? ))
Your calculation for the low pass (woofer) is wrong as you have connected four 8 ohms woofers in parallel.
So the effective impedance will be 2 ohms for the inductor calculation.
Parallel - series. Look closely .
Felicitaciones amigo! Me gusta mucho el diseño. Saludos.
Thank you Jairo.
New SUBSCRIBER here🎉🎊
Great DIY Sir💯✨
Tanong ko lang Sir ano dimensions ng speaker box?😊
Thanks. There is a better center channel speaker project, go to this video - th-cam.com/video/66dKLHq3wi0/w-d-xo.html
Salamat Sir 😃👍
Bisaya diay ko Sir 😁
Ganahan kaayo ko sa imoha DIY Sir💯👏
Pila pud pabuhat ana Sir?😄
Sir ano po ang total wattage at total impedance ng dalawang 300 watts at dalawang 150 watts tweeter
Isang midrange 150 watts
8 ohms po lahat at may dividing network na 600 watts..
What types of speaker are best for diy boombox ? I allready have 4pis 4inc 40w(aes) woofer and i use those all 4 and now what's i need like subwoofer tweeters and quantity.?
Yes you need subwoofer to add bass.
tbh it looks fresh
nice center speaker
Yes sir thank you
Do you have any DIY Satellite Speaker? and how about the Amp for Center and Satellite? Thanks in Advance
Hello Monzur, I hook all my speakers to a mini 5.1 class D amp shown in the beginning of the video on my desktop.
(full range speaker) series parallel combination, similar from bose 901
Nice work keep it up man.....
Wow
Thank you very much. ^_^
your welcome ^_^
1:07 thought that was a dead dear for a second!!!
😂🤣
what plywood is that by looking it not a birch?
Sir i need some guide... I have an 8inch 200w sub woofer... What components do i need to build?
A fresh sheet of MDF or plywood, some basic tools and that's it.
That’s a really high crossover point
It all depends, I wouldn't say it's high at all considering the drivers. Small midrange or fullrange speakers can play well over the crossover seen here and small tweeters can't play very low.
Outstanding! Thank you for showing this. I am just about to finish up my truck and I was thinking about a center speaker somewhere in the dash. BTY, how did your plywood box turn out?
Hello Robert, that project was a fail. Watch this recently done center speaker. - th-cam.com/video/66dKLHq3wi0/w-d-xo.html
That configuration has to be a 2 1/2 or 3 way. It can't be a 2 way. It will sound much better!
hey bro thanks for sharing your video nice and cool, so you can set up a speaker?
No problem, anytime. Let me know anything I can be of any help.
Nice video
Thanks Sana
Next time use a hole saw for the larger speaker holes. Jig Saw for 4 round holes seems counter-intuitive, sloppy, and slow.
I agree.
How do you connect 4 or more speaker on a stereo Bluetooth module?
Will you show those speakers wiring diagram, plz?
3:49
Nice video, can i use a same wireing for the 2nd order Linkwitz Riley?
This wiring will reverse the polarity on 2nd orders.
Thank you for answer, i'm still learning about this so i will use a 1order like you in the video. Keep up with a good work!
Hi you used mid range speaker,can I buy the cross over some where?, thank you
Yes I believe you are in a country that has aplenty of available electronic goods. Here in the Philippines so rare to find such, so I ended up DIY'ingn them.
How I wish I have your skill set..
and how we add small Bluetooth amplifier to connect the usb mic and memory card etc nd amplifier is may be 250 watt support
Hello Surendra, you need to purchase a Bluetooth/digital module and connect it to your amplifier. There are many of amplifiers that already has Bluetooth and digital input/output. I hope you can find them.
Hello,
how do you calculate wire size ?
Hello there is an online tool in winding coils - www.pronine.ca/multind.htm
I cant believe he got that good of sound from that nothing crossover. i really thought it would sound like shit..
Don't judge a book by its cover. You saw how each component of the crossover was measured using LCR multimeter.
I have 3 different speakers so how do I help it in 1 cabin at the same time
nice sounds
box size?
4 drivers ..one port? not even centralized?? the air from the furthest drivers .......oh dear ...someone didn't think why they put two ports in 4/5/6 driver arrays lol
nice sounds...
☺️
Sounds great Sir :)
i just saw the video that you've been here in Iloilo City, 2 weeks ago Sir 😅
nandito ka pa rin po ba sa Iloilo? o bumalik kna po sa Butuan City?
Thanks for watching. Just 2 days in Iloilo for the WordCamp. 😆
@@chrclmnky Ahh, hehe 😅You're welcome po Sir 🙂
God Bless po and more vids/DIY projects to come 🙂
They sound good, thanks for not demo-ing with Gay music!
😆
Sir what is the length and the width of box???
Seems like the concept of HDD (RAID- 1+0) has been implemented over here....! 😎
Yes similar concept.
Madyaw karadjaw, Butuanon!
Many thanks!
Kuya paturo nman ako pano gawin ung cross over mo?gusto ko din gawin tong center speaker mo eh.thanks
Madali lang. Watch my other video about crossover building.
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
**inhale**
**exhale**
All speaker connection in parallel?
Series - parallel
Any reason why you inserted the cotton foam inside?
Hello Justin, they are polyester fiber fill. Stuff them inside to eliminate speaker vibration from resonance.
CHRCLMNKY oh okay
Does that crossover website work well or are there better websites for that? Anybody?
Hello how you doin, practically all other crossover calculator web based apps are pretty much the same.
Bhi eska amplefire kitna watt ka ha bhi plz mujko thora bathoui
4.1 का bass कैसे बनाते हैं👍
I love you man .!
Where do you get the square Tweeter at or what's the name of it so I can get four pair
Hello Horace. It is just a common 3" woofer. Mostly available in that shape. The circle ones are bit expensive.
which frequency did u use for calculating inductance?
Sorry I forgot the specific frequencies but I used these calculators:
www.apicsllc.com/apics/Misc/filter2.html
@@chrclmnky must be 1khz normal LCR meter thanks for the site 👍
can you give me the dimension of the box speaker?
Where did you buy the speakers?
Hello Raynedson, bought them from a local audio-electronics store here in my city.
Bonjour jolie travaille
hey nice video there, when will you make a tline speaker cant wait for these for you to make.
diebold man Please do check my review on PHILIPS MMS 8080b speakers here is the link
th-cam.com/video/IQwM6aoN3RI/w-d-xo.html
Ganyan balak design ng box mag kanu kaya sa inyo ganyan... Pls reply
Can i use TPA3118 PBTL Digital Amplifier with usb power run
Yes you can
Is the tweeter Dayton?
A generic Chinese-made, square Yamaha tweeter copy.
Can you make one for deeper bass n only 2 speakers and 2 tweeters
Yes sure
@@chrclmnky CAN YOU SALE IT TO ME I WANT TO UPGRADE MINE
Suggest me crossover for it ??
Hello, any crossover that has 3700Hz dividing point @ 8 Ohms
Please give me link from you buy this speakers
What are your messurments of the box please
Lina inch ka ha speaker
Sir may video po ba kayo kong pano gawin yang crossover at icalculate ? Salamat po..
Yes sir, watch my old videos. Also that 100percent diy crossover on my channel. Thanks!
@@chrclmnky okay thanks
Teh
@@dakshshaurya9817 ate ?
Sir i want to make 5.1 home theater with good base.please can u tell me all spare part which are required like woofer ,speakers,tweeters,board.i want to use like home theater.directly connect to plug board in home.if u tell me i will go to electrician to connect them.please tell me sir
Let me guess, you are indian?
@@nikolapoljak9260 yes sir
@@nikolapoljak9260 wt is the problem if we are Indians..can't u tell us the Speakers specifications..
Read the description. He use a generic speaker w/c can be bought online. Idk if thats available in your country.
Center Speaker must ring as a patato...?
The box is poorly made...
boss ilang watts na amplifier ang pwd sa ganyan?salamat
150-700w
Nunca abia visto una conexión así,es interesante
Thanks Delfino.
I did not understand the connection of the speakers think that they would all be connected in parallel what is the final impediment grateful
Hello Marcelo, a combination of series and parallel as shown in 3:51
Use cross over
@@lovekush9103 yes it has
Sir how much apply volt in this divise
Катушки для фильтров не наматывают на железные сердечники, что бы избежать искажений, возникающих от перемагничивания.
Yes sir I agree.
hi, im a modular cabinet maker, we can be partner in making good and quality speaker.
That would be cool.
What is up
what is RMS wattage of your amplifier
Just 200 i think
@@chrclmnky ohh means u can add 4 more same speakers? by d way thanx for ur reply