As a nwbie 90 years old I worked two months to be able to upload codes to my Esp32, and you are the only one that helped me to be able to go through with this new project I deeply want to thank you again , you are the best of all the video that I tryed with no results.
This is so refreshing, I am so inspired by you. waw, at 90 you still love to do all these, so cool. I send my love to you sir. Thank you too RJ channel owner for good turorials
After years of using the STM32 bluePill, I decided to check out the ESP32. Your video makes it look really easy - I get my device today, so I will be following you examples closely
Thank you for this very helpful video. I would just like to make two things clear if anyone is using the ESP32 DevkitC 38pin version, the built in LED is on IO 1 and not IO2. The second thing that needs mentioning, is when you download from the Arduine IDE to the board once it has compiled the program and then starts to download using the com: port, you must push and release the Boot button for 2 seconds, the download will then run correctly.
You are very welcome. The best thank you for me is to not skippin the ads and Subscribe 🔔 to my channel, like 👍 the video and do not skip the ads.. It is greatly appreciated. 🔔 😊. I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊 .
For anyone not able to upload a sketch. make sure to hold down the "boot" button before uploading. when u see connecting...___... release the button and it should work...took me ages to figure out as i thought my board was bad!
I have done it 100s of times. you don't need push any button. The ENABLE pin is being controlled by the code when you press upload icon on Arduino IDE.
on the ESP32 WROOM that has 3.3 and 5V pin for power Where is the Vin Arduino had 3.3 5V and Vin I have a power source 5V External source that i need to plug in to the board but not via USB WHAT PIN DO I CONNECT AN EXTERNAL 5V SOURCE TO FOR POWER
@@robojax No that's not what i meant i was very clear on what i meant here it is again - Arduino has 3.3V and 5V (when connected to USB these pins provide power OUTPUT) However it also has a Vin (This is an INPUT) Because the USB Port that supplies the 3.3 and 5V can only supply up to 1A it has limitations when working with LED Strip projects. if you need more current you connect a separate supply to the Vin (This is an INPUT) - My Question again is... on the ESP32 Where is the Power Input ? We have a 3.3V and we have a 5V (i assume these are Outputs) because you need the USB Input to make the work What i meant was WHERE DO I CONNECT AN EXTERNAL 5V POWER SOURCE TO WHERE IS THE INPUT THAT I CONNECT AN EXTERNAL 5V SOURCE TO ? that's what i meant
Nice and very informative video. I'm about to get one of these for myself but I'm not sure which one would be better to get. I've noticed that the 38pin one has 5V output pin which might be useful but it is missing VIN pin. So how to power it up other than using micro usb port? Am I missing something?( I am new to arduino and all those modules). Any help appreciated.
Thank you. It is hard to always get something that you be happy with fully. I would suggest getting the 38 pin. They are produced many sellers so don't expect that all be the same.
Hey sir, I'm doing a project based on esp32 and the only issue I am facing with is my HTTPClient.h file and no matter what, I am not able to find the right repos or built in versions, so could you kindly guide me as to where you downloaded that file from
Hi, I am not sure if I talked about HTTPClient.h. may be you just do a Bing search and see if you get something useful www.bing.com/search?q=HTTPClient.h+github+esp32&qs=n&form=QBRE&sp=-1&lq=0&pq=httpclient.h+github+esp32&sc=10-25&sk=&cvid=EDA762214BCB49239FA47BFCF06AD103&ghsh=0&ghacc=0&ghpl=
After upload everything all the relays are connected to my esp32 module now trying to use 8ch bluetooth app it will not put out any signal only my button are working I need help
Thank you very much for this tutorial ❤! I worked through this project and had everything working. But now, when I recompile and upload the code (the exact same code was working before) on any of my ESP32 boards, I get a PSRAM error ("psram: PSRAM ID read error: 0xffffffff" displayed in the Serial Monitor). The the only solution I've found online relates to PlatformIO, not Arduino IDE. May I ask, do you know what might have caused this (especially since it worked before) and how to possibly fix it?
Hi, either you selected incorrect RAM from the Arduino settings or the code has something that causes this such as writing to RAM or huge code. Not sure.
@@robojax Thank you very much. I'll try to see if that happened, and if I do figure it out, I will post a reply/fix here in case anyone else runs into this issue.
i have the same esp32 but i have to use a capacitor between en and gnd in order to program it which is not always a viable option. is there any way to eliminate the capacitor problem.
have you prepared your Arduino IDE for ESP32 or not? do that first. then for test, use the provided code with the library. Then use the code I provided.
Sir, My board name is ESP-32s but I can not find this name on tool-> board-> list. There are some other esp32 boards but not the one I have. What should I do Sir? Can I connect this to any other board, like Node32s or ...? Will there be any problem if I select other board?
Hi, because you have skipped the video and did not follow instruction. you have to prepare Arduino IDE to work with ESP32. I have explained it in the video.
@@robojax Thank you Sir for your quick response. I have done that and it shows the all options, like the one you mension in the video ESP32 WROVER MODULE and there are many more esp32 modules, but unfortunately it does not show the ESP32-S MODULE. So I have connected to Node32s and it has worked for now. I will watch your video again to make that I followed all the steps. Thanks alot!
hi robojax, someone mentioned using Arduino IDE is not the optimum way to program the esp32... why would that be? thanks a lot for the videos, you're a great teacher!
it is true but very hard for many people. Arduino IDE is the most easy to use option. Learning Paython and command line is new language. But here you just copy and paste the code and it works.
I think the statement might be referring to you not being able to use the two CPU cores effectively. Generally, as I understand, in default mode one core is dedicated to WIFI. But you can use other IDEs to distribute threads between the two cores, but not with Arduino IDE.
I am turning to you for help my esp32 don't seems to send signal to my relays I can activate the relays with a wire, my apps is paired with my esp, but touching the buttons on my apps the esp32 appears dead, could I have a bad one I thank you sir
Hi, there are 100s of apps. you need to contact the application developer as I can't install an app and test it. Most apps are spywere. but I have vodes that you can control devices using without app just your phone browser. Search my channel for ESP32 or ESP8266 and you will see them.
Hey, I need help, I am not able to upload any code in my esp32, the error it shows is " A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header " , can you help me in this
If you connect sensors to the ESP32, you can inject their data into the page. That way, even if the ESP32 is not a Web Server, it is able to add the values to a webpage, that is actually being provided by a different server. So you can have your own webpage that shows all sorts of data, that your ESP32 and it's sensors collects.
Thanks for the nice video. I got the same 38P version. Firstly it does not have the LED on pin 2, but one can connect an external LED to 2 or even a volt meter, and you will see, that it works. More importantly, in the production of the version 38P board, they seem to have made a big mistake and have marked the second pin on the left side of the RST button, just next to V5 as "GND". It is actually the "CMD" pin, or GPIO 11. Very confusing!!
I followed your code but my ESP32 WROOM32D keeps on getting this error (Failed to extract VCRUNTIME140.dll: decompression resulted in return code -1!). What could be the reason?
The problem is with your windows not the ESP32. a simple search showed this solution answers.microsoft.com/en-us/windows/forum/all/vcruntime140dll/b1a15b0e-e389-41a3-bc49-f4fc85bac575 look at the bottom link and install "Microsoft Visual C++ 2015 Redistributable Update 3 RC" also I am not sure if you watched the introduction to ESP32 or not. it might be the issue. The link is in the description.
can you help me, please? Arduino: 1.8.12 (Windows 10), Board: "ESP32 Dev Module, Disabled, Default 4MB with spiffs (1.2MB APP/1.5MB SPIFFS), 240MHz (WiFi/BT), QIO, 80MHz, 4MB (32Mb), 921600, None" Sketch uses 207705 bytes (15%) of program storage space. Maximum is 1310720 bytes. Global variables use 15228 bytes (4%) of dynamic memory, leaving 312452 bytes for local variables. Maximum is 327680 bytes. esptool.py v2.6 Serial port COM8 Connecting........_____....._____....._____....._____....._____....._____.....____An error occurred while uploading the sketch _ A fatal error occurred: Failed to connect to ESP32: Invalid head of packet (0x0D) This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
if you have other wires corrected, remove them all. Sometimes it is the settings for the board type or board is moving while uploading. try it again it should work. I have seen this before.
Thank you for covering this. Fantastic! Can you give a tutorial on battery management for simultaneous charging and usage for ESP32? Maybe using the SparkFun Thing Plus as your model? Love the walkthrough, thank you!
السلام علیکم احمد عمر، شکراً. انا احمد من الخراسان الکبیر. الدیار الامام البخاری، الترمذی، امام نسایی، ابو دادو و ابن ماجه كلهم فارسيون من خراسان. الناس في خراسان أهل السنة. تسمى خراسان الآن أفغانستان وأوزبكستان وطاجيكستان وتركمانستان وشرق إيران.
Hola , excelente video , muy buen modulo el ESP32 , voy a averiguar cual es el costo ya que la economia de mi pais es desastrosa con relación al dolar , Argentina tiene una gran inflación y todo esta dolarizado , desde ya te felicito por tu canal ya que es verdaderamente un placer su contenido , Sos realmente bueno en estos temas , Gracias !!!!!
Hola Vincente, gracias por escribirme. Les deseo lo mejor y espero que la inflación termine en Argentina y que la situación económica mejore. Ahmad de Canadá
@@robojax Muchas Gracias , eso espero ,realmente , Canada es un Gran Pais , casualmente , tengo algunos parientes , en winipeg man. Winnipeg, Manitoba , una hermana y un hermano de mi padre , su hermano ya fallecido , bueno distintos destinos de inmigrantes Italianos , un primo hijo de su hermano es ingeniero en electrónica , ya hace unos años lo pude conocer , realmente este pais parece condenado al fracaso , es triste , espero que superemos esta crisis , muchas gracias por tu comentario , Sos una persona muy capaz , tenes pinta de Buen Tipo !!!! Saludos !!!! Un Abrazo !!!!
Sí, de hecho, Canadá es uno de los mejores países del mundo para vivir. Cada año, más de 300,000 personas migran a Canadá. Le invitamos a venir a Canadá (www.canada.ca/en/immigration-refugees-citizenship/services/immigrate-canada.html) La distancia desde mi ciudad Ajax, a Winipage es de 2500 km en mi oeste. Les deseo lo mejor a usted y a su familia. Gracias por los comentarios.
As a nwbie 90 years old I worked two months to be able to upload codes to my Esp32, and you are the only one that helped me to be able to go through with this new project I deeply want to thank you again , you are the best of all the video that I tryed with no results.
Wow 🤩 that’s amazing. Pleased to know my tutorial helped you. Keep it up. Stay safe.
This is so refreshing, I am so inspired by you. waw, at 90 you still love to do all these, so cool. I send my love to you sir. Thank you too RJ channel owner for good turorials
When your grandsons tell you about youtube lol
Something about this video and Ahmad just feels right. Thank you for the thorough and clear explanation!
Glad you liked it!
YOU HAVE A GIFT for everything electronics.. Thank you for sharing it with us. God bless.
After years of using the STM32 bluePill, I decided to check out the ESP32. Your video makes it look really easy - I get my device today, so I will be following you examples closely
good luck ESP32ing.
Thank you for this very helpful video.
I would just like to make two things clear if anyone is using the ESP32 DevkitC 38pin version, the built in LED is on IO 1 and not IO2.
The second thing that needs mentioning, is when you download from the Arduine IDE to the board once it has compiled the program and then starts to download using the com: port, you must push and release the Boot button for 2 seconds, the download will then run correctly.
Thank you Ron for the comments. Pushing the push button switch is part of the code and it should be done automatically.
best video on the esp32 dev kit! much informative very thanks
You are very welcome. The best thank you for me is to not skippin the ads and Subscribe 🔔 to my channel, like 👍 the video and do not skip the ads.. It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊 .
For anyone not able to upload a sketch. make sure to hold down the "boot" button before uploading. when u see connecting...___... release the button and it should work...took me ages to figure out as i thought my board was bad!
I have done it 100s of times. you don't need push any button. The ENABLE pin is being controlled by the code when you press upload icon on Arduino IDE.
As always the video is on point and very detailed 👊🏽
Thank you.
Thank you sir.. I have learn a lot best explaination....
You are welcome.
on the ESP32 WROOM that has 3.3 and 5V pin for power
Where is the Vin
Arduino had 3.3 5V and Vin
I have a power source 5V External source that i need to plug in
to the board but not via USB
WHAT PIN DO I CONNECT AN EXTERNAL 5V SOURCE TO FOR POWER
you meanted "5V pin for power" that is where youo connect.
@@robojax
No that's not what i meant
i was very clear on what i meant
here it is again
- Arduino has 3.3V and 5V (when connected to USB these pins provide power OUTPUT)
However it also has a Vin (This is an INPUT)
Because the USB Port that supplies the 3.3 and 5V can only supply up to 1A it has limitations when working with LED Strip projects.
if you need more current you connect a separate supply to the Vin (This is an INPUT)
- My Question again is... on the ESP32
Where is the Power Input ?
We have a 3.3V and we have a 5V (i assume these are Outputs) because you need the USB Input to make the work
What i meant was
WHERE DO I CONNECT AN EXTERNAL 5V POWER SOURCE TO
WHERE IS THE INPUT THAT I CONNECT AN EXTERNAL 5V SOURCE TO ?
that's what i meant
Nice and very informative video. I'm about to get one of these for myself but I'm not sure which one would be better to get. I've noticed that the 38pin one has 5V output pin which might be useful but it is missing VIN pin. So how to power it up other than using micro usb port? Am I missing something?( I am new to arduino and all those modules). Any help appreciated.
Thank you. It is hard to always get something that you be happy with fully. I would suggest getting the 38 pin. They are produced many sellers so don't expect that all be the same.
Hey sir, I'm doing a project based on esp32 and the only issue I am facing with is my HTTPClient.h file and no matter what, I am not able to find the right repos or built in versions, so could you kindly guide me as to where you downloaded that file from
Hi, I am not sure if I talked about HTTPClient.h. may be you just do a Bing search and see if you get something useful www.bing.com/search?q=HTTPClient.h+github+esp32&qs=n&form=QBRE&sp=-1&lq=0&pq=httpclient.h+github+esp32&sc=10-25&sk=&cvid=EDA762214BCB49239FA47BFCF06AD103&ghsh=0&ghacc=0&ghpl=
I have learned a lot. Thank you so much Robojax.
You are very welcome.
Can we 5V directly from the laptop as an input to esp32?
yes you can.
After upload everything all the relays are connected to my esp32 module now trying to use 8ch bluetooth app it will not put out any signal only my button are working I need help
Thank you very much for this tutorial ❤!
I worked through this project and had everything working. But now, when I recompile and upload the code (the exact same code was working before) on any of my ESP32 boards, I get a PSRAM error ("psram: PSRAM ID read error: 0xffffffff" displayed in the Serial Monitor). The the only solution I've found online relates to PlatformIO, not Arduino IDE. May I ask, do you know what might have caused this (especially since it worked before) and how to possibly fix it?
Hi, either you selected incorrect RAM from the Arduino settings or the code has something that causes this such as writing to RAM or huge code. Not sure.
@@robojax Thank you very much. I'll try to see if that happened, and if I do figure it out, I will post a reply/fix here in case anyone else runs into this issue.
Hi do you have a video about traffic lights using this board?
Hi, please used the code provided here th-cam.com/video/OSwleCBlkuI/w-d-xo.html
Thanks a lot. You're the best
You are!
i have the same esp32 but i have to use a capacitor between en and gnd in order to program it which is not always a viable option. is there any way to eliminate the capacitor problem.
you don't have to connect anything . just connect your USB and follow as I have shown.
wonderfull explained,learned alot of it valueable information ,subcribed
Thanks and welcome
Why i cant upload the program? The terminal arduino ide show the sentenses " leaving... Hard resetting via RTS pin. Im using your code
have you prepared your Arduino IDE for ESP32 or not? do that first. then for test, use the provided code with the library. Then use the code I provided.
Same problem
Sir, My board name is ESP-32s but I can not find this name on tool-> board-> list. There are some other esp32 boards but not the one I have. What should I do Sir?
Can I connect this to any other board, like Node32s or ...?
Will there be any problem if I select other board?
Hi, because you have skipped the video and did not follow instruction. you have to prepare Arduino IDE to work with ESP32. I have explained it in the video.
@@robojax Thank you Sir for your quick response.
I have done that and it shows the all options, like the one you mension in the video ESP32 WROVER MODULE and there are many more esp32 modules, but unfortunately it does not show the ESP32-S MODULE. So I have connected to Node32s and it has worked for now. I will watch your video again to make that I followed all the steps.
Thanks alot!
hi robojax, someone mentioned using Arduino IDE is not the optimum way to program the esp32... why would that be? thanks a lot for the videos, you're a great teacher!
it is true but very hard for many people. Arduino IDE is the most easy to use option. Learning Paython and command line is new language. But here you just copy and paste the code and it works.
I think the statement might be referring to you not being able to use the two CPU cores effectively. Generally, as I understand, in default mode one core is dedicated to WIFI. But you can use other IDEs to distribute threads between the two cores, but not with Arduino IDE.
hi, after installing the esp32 board on arduino ide, i cannot choose port. it is grey in color for the port and i cannot click it. may i know why?
Hi, it must be the driver. See this video and to make it work th-cam.com/video/u_21yNqd03I/w-d-xo.html
@@robojax thankyou so much, finally i can use my com port 🙏🏻 you are amazing sir, keep on making IoT thing videos and help people 🙏🏻
I am turning to you for help my esp32 don't seems to send signal to my relays I can activate the relays with a wire, my apps is paired with my esp, but touching the buttons on my apps the esp32 appears dead, could I have a bad one I thank you sir
Hi, there are 100s of apps. you need to contact the application developer as I can't install an app and test it. Most apps are spywere. but I have vodes that you can control devices using without app just your phone browser. Search my channel for ESP32 or ESP8266 and you will see them.
Hey, I need help, I am not able to upload any code in my esp32, the error it shows is " A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header "
, can you help me in this
Make sure to disconnect anything else connected to the module.
@@robojax it was just module connected to the usb, no other sensor, or led , etc etc. still facing same problem.
may be your computer is not supplying 5V properly. connect external 5V to Vin pin. and gnd.
What code do I need for bluetooth autopilot on my cell phone
Won’t work with Bluetooth unless you write your own code
Thank you sir.
For such a nice video.
Iam happy just to see your face
but the link is working without esp as well..
What was the use of esp in httpclient ??
I have explained it in video. You must have escaped. Please watch it.
If you connect sensors to the ESP32, you can inject their data into the page. That way, even if the ESP32 is not a Web Server, it is able to add the values to a webpage, that is actually being provided by a different server. So you can have your own webpage that shows all sorts of data, that your ESP32 and it's sensors collects.
Thanks for the nice video. I got the same 38P version. Firstly it does not have the LED on pin 2, but one can connect an external LED to 2 or even a volt meter, and you will see, that it works.
More importantly, in the production of the version 38P board, they seem to have made a big mistake and have marked the second pin on the left side of the RST button, just next to V5 as "GND". It is actually the "CMD" pin, or GPIO 11. Very confusing!!
Thanks for the info!
Good & fast explanation, thanks
you are welcome. I am glad you found it useful.
I followed your code but my ESP32 WROOM32D keeps on getting this error (Failed to extract VCRUNTIME140.dll: decompression resulted in return code -1!). What could be the reason?
The problem is with your windows not the ESP32. a simple search showed this solution answers.microsoft.com/en-us/windows/forum/all/vcruntime140dll/b1a15b0e-e389-41a3-bc49-f4fc85bac575 look at the bottom link and install "Microsoft Visual C++ 2015 Redistributable Update 3 RC" also I am not sure if you watched the introduction to ESP32 or not. it might be the issue. The link is in the description.
@@robojax thank you sir for the response. I have now run ESP32.
What code do I put in the ide for esp32 cam
Ewing video , please see the video about camera th-cam.com/video/5XCb3t8J4Kg/w-d-xo.html
ESP32 library package not showing in Arduino IDE 2.0.3 Board Manager.
nm, I downgraded to 1.8.0.
Of course it will not show. You have skipped the video. You gotta install it to see it. Please watch fully.
Thanks for your beautiful videos.
So nice of you
Please do a comparison video between these.
I believe I did. I mentioned why they are different.
Great channel. Subscribed
Awesome, thank you!
Great, thanks. I subscribed
Thank you very much.
ماشالله احمد
can you help me, please?
Arduino: 1.8.12 (Windows 10), Board: "ESP32 Dev Module, Disabled, Default 4MB with spiffs (1.2MB APP/1.5MB SPIFFS), 240MHz (WiFi/BT), QIO, 80MHz, 4MB (32Mb), 921600, None"
Sketch uses 207705 bytes (15%) of program storage space. Maximum is 1310720 bytes.
Global variables use 15228 bytes (4%) of dynamic memory, leaving 312452 bytes for local variables. Maximum is 327680 bytes.
esptool.py v2.6
Serial port COM8
Connecting........_____....._____....._____....._____....._____....._____.....____An error occurred while uploading the sketch
_
A fatal error occurred: Failed to connect to ESP32: Invalid head of packet (0x0D)
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
if you have other wires corrected, remove them all. Sometimes it is the settings for the board type or board is moving while uploading. try it again it should work. I have seen this before.
@@robojax okay thank you very much
you are welcome.
Thank you for covering this. Fantastic! Can you give a tutorial on battery management for simultaneous charging and usage for ESP32? Maybe using the SparkFun Thing Plus as your model?
Love the walkthrough, thank you!
Great suggestion!
@@robojax thank you that would be amazing. I don't see much content on this so it would be a first!
And maybe cover how to create battery status indicator lights too : )
Good video! do you know what I like about you? you are here for science, not for money. Most people learn for money, not for knowledge.
😊 Thank you.
Nice T Shirt
Nice one
thanks
my esp shows fatal not connecting plz help
if you have anything else connected to ESP32, disconnect hem and try it again. I don't know other than that why.
Thanks Robojax
The espuno32 looks a lot like the wemos d1 r32
ESP32 has Bluetooth which the other does not .
تحيا مصر ❤️❤️
السلام علیکم احمد عمر، شکراً. انا احمد من الخراسان الکبیر. الدیار الامام البخاری، الترمذی، امام نسایی، ابو دادو و ابن ماجه
كلهم فارسيون من خراسان. الناس في خراسان أهل السنة. تسمى خراسان الآن أفغانستان وأوزبكستان وطاجيكستان وتركمانستان وشرق إيران.
@@robojax ما شاء الله اخي تشرفنا بمعرفتك و شكرا علي المعلومات المفيدة اخوك احمد من مصر جزاك الله خيرا
ما شاء الله انت من بلاد العلماء نفعنا الله بعلمكم
came here to learn about how to install esp32 on arduino and all i get is a wave of the hand. no help here
Hello, you came to the full details video. here is the short video th-cam.com/video/4OOFlS75owA/w-d-xo.html
It is so hard to understand people who don't have English as their first language. It is far to common on TH-cam and the internet in general.
yes it is hard when you don't English. Just read comments from people.
Hola , excelente video , muy buen modulo el ESP32 , voy a averiguar cual es el costo ya que la economia de mi pais es desastrosa con relación al dolar , Argentina tiene una gran inflación y todo esta dolarizado , desde ya te felicito por tu canal ya que es verdaderamente un placer su contenido , Sos realmente bueno en estos temas , Gracias !!!!!
Hola Vincente, gracias por escribirme. Les deseo lo mejor y espero que la inflación termine en Argentina y que la situación económica mejore. Ahmad de Canadá
@@robojax
Muchas Gracias , eso espero ,realmente , Canada es un Gran Pais , casualmente , tengo algunos parientes , en winipeg man. Winnipeg, Manitoba , una hermana y un hermano de mi padre , su hermano ya fallecido , bueno distintos destinos de inmigrantes Italianos , un primo hijo de su hermano es ingeniero en electrónica , ya hace unos años lo pude conocer , realmente este pais parece condenado al fracaso , es triste , espero que superemos esta crisis , muchas gracias por tu comentario , Sos una persona muy capaz , tenes pinta de Buen Tipo !!!! Saludos !!!! Un Abrazo !!!!
Sí, de hecho, Canadá es uno de los mejores países del mundo para vivir. Cada año, más de 300,000 personas migran a Canadá. Le invitamos a venir a Canadá (www.canada.ca/en/immigration-refugees-citizenship/services/immigrate-canada.html)
La distancia desde mi ciudad Ajax, a Winipage es de 2500 km en mi oeste.
Les deseo lo mejor a usted y a su familia. Gracias por los comentarios.
you are not from Canada حبيبي
why would you say that? You can be from anywhere. The earth belongs to Allah and we all die. more peope come and go until Qyamah.
2020 this example not work
"not work" is not enough. provide error or something. It works. there is not issue if you follow instruction.
Hi, Where am I going to edit the body of the URL like "Welcome to DDAS.cc", "User:", "Temperature is" Please explain?
Hi, it is a service. Coming soon.