วีดีโอ

Is that 5K or 6K 🤔🧐

You need to work on filming and editing. You have a wandering camera showing nonessential video. Use a tripod with a wider angle and do some editing of useless video (of which the was a lot).

Good thing I drive a cx5

Be nice on air bag suspension

Never in my life have I seen a professional make such a mess when doing an oil change. Also, using a ratchet to undo tight nuts is the quickest way to ruin your ratchet.

The drain plug screw on mine is so tight i cant loosen it with a typial socket wrench. Not sure how to loosen it.

What is that you are removing at 1:17? I know the sway bar link but what is the square box? Also the item you grab at 1:34? Never seen anything like these before.

When dropping it, did you replace any other parts like the end links or anything to it, asking because I just dropped my 2020 mazda cx5 and wanted to see if replacing the end links necessary

Very good video thank you 🙏👍👍👍👍👍👍👍👍👍 save money 💰

Great info, music much too loud...

On the mazda forums, one of the things they worry about is cylinder scoring. Apparently the 0W20 is too thin to cling to the cylinder walls causing ring scoring of the walls. The manual says you can safely use 5W30 in hot conditions. This will cling better to the cylinder walls at the cost of slight mpg reduction.

How did you get those rear bump stops back in the boot, your video cuts off at that part

Excellent video my dude. Quick question, may I ask where you placed your hoist-lifting arms? Did you place them on the cross member or in the pinch weld designed for jack stands?

How does the rubber boot attach at the bottom of the front shocks?

Martinez Charles Young Scott Rodriguez Frank

I’m sure it’s too stiff and the driving is too bumpy. I’ve done that before. It’s no worth it.

Check cabin filter and lube all parts and check all fluid

What would be really helpful is if in the description, you listed all the size tools you need. Looks like 15-17-19mm?

@ 38:45 all I was thinking was, man, a good old school GM distributor wrench would really help right now. Those were typically 9/16 and I doubt there is any thing on a Mazda that isn't metric.

Clean the oil off the engine cover. U got hand prints all over. Just saying. First thing people will notice when the hood is popped open. Little details make the job.

How nice video!Do you interested in product review? How can I contact with you?

I wish someone like corksport would offer a quality rear spoiler for the cx5 22 and up.

Can I use these on a 2019 model?? Should be fine right??

So with these lowering springs, does it help with that god awful wobble on the cx5? I had a rental and was impressed but the wobble over bumps scares the crap outta me and doesn't feel stable.

They are great SUVs, got my 2016 to nearly 300 000km with only reg maintenance, 3 rear wheel bearings, and a complete brake discs / pads job around 160k. No rust at all on the body, and I live in Quebec (snow / salt / gravel..) Wife has a 2021 CX5 and it is rock solid too

That old oil looked dark.

Did you need and alignment after removing the front shocks?

What's the oil filter wrench you use?

Why would you want to lower?

not bad but i fully drain all my oil and even wash it a bit with new oil before putting the drain plug and filter.

great job! clean and nice

Great video, do I have to reset the computer so I know when to change it next time, 7,500 miles??

You may have said it and I missed it but what did you tie into for all or most of the lights? I have a light switch inside my kitchen which controls the lights and even if the garage door is on or not. Is it possible to tie into the same wires or the garage door, how is that process achieved?

Hi if someone can tell me. Would this be the same ride height for the fwd ? I can’t seem to find anybody with corksport Fwd

NICE

Last month I decided to lower my 2018 CX5 Grand Touring but I wasn't sure what fitment I wanted to go with. After watching this video, I bought the same Corksport springs, 245/45R20 Pirelli tires, with the 20" black rims I had on my old Mitsubishi Outlander and it looks so good! Plenty of clearance, no rubbing, the alignment is good and showed the camber is barely off, and I was told it should have no impact on the tire wear. Thank you so much for all the information! Everything else is stock on the car. It drives really nice, corners great like it's on rails, no more roll, ride is great on smooth streets, but can be jarring at times because many of these San Diego roads in my area are pitiful. I never noticed how bumpy the streets are in my area until now. Is there something I can do to help with this ride on these bumpy roads?

That hole saw should be tight not flopping around like that.

My guy I have a question I recently did that and I have 20 inch rims but one of them one of those shocks was messed up so we change it now it looks like any Campbell adjustment do you did that to yours

What’s the Kent product on your bench ?

Nice

Corksport doesn't seem to carry these for the 2023 Signature I had to go H and R and I will couple that with Bilstein B6. It will probably end up being stock height out of the box and then lower about an inch as it breaks in. Hope this cuts down the understeer. . . . . .Update, the H and R springs and B6 Bilstiens (with cut bump stops like this video) gave me about 2" of drop front and rear. Now the stock 19" wheels look correct in the wheel well. It rides about as smooth as stock. on small bumps (that glide feeling), . . . a little more firm over larger bumps but it cleaned up the handling. No more understeer at normal speeds (speed limit cornering). I will update again after it breaks in and I push it on a mountain road.

nice video! very good service. mind if i ask if youd recommend using other oil filters such as amsoil or should i stick with the oem thats made by tokyo roki/mazda?

Can these lowering springs work on a 2022 Mazda cx9

how did you pull the wires to each light?

How’s the ride?

What color are your walls and ceiling? Ive read Tricorn black by Sherwin williams for home theaters is what they use. Im thinking of painting my garage ceiling tricorn black. Its a neutral color, pairs nice with white for a classic contrast

Might be a good idea to have an oil analysis done as well to look at wear and fuel dilution. I'm going to try one of the Oil Analyzers kits from Amsoil to keep tabs on my '23 Turbo.

Any issues with axle CV joint angle / wear after lowering?

Often the shaft can be held with a very small wrench. Like 3mm

No crush washer part number?