justanengineer
justanengineer
  • 76
  • 1 181 728
DIY Ultrasonic Microphone Recording Jammer for Android phone and iPhone
Build your own Ultrasound Microphone Jammer and protect your privacy !
This is as good as F11 jammer from China (shown in Linus techtips video ) but you can make it on your own
Project page :
github.com/mcore1976/antispy-jammer
For the setup : DIGISPARK + TPA3116D2 + AD9833 + IRF4115 + Coils 3.3 miliHenr + resistors 10KOhm :
New source code for testing :
raw.githubusercontent.com/mcore1976/antispy-jammer/main/mic_jammer_digispark_ad9833_new_version5.ino
The connection diagram for Digispark:
github.com/mcore1976/antispy-jammer/blob/main/mic-jammer-AD9833-TPA3116D2-IRF-coils.png
For the setup : Discrete ATTINY85 + LM7805 + TPA3116D2 + AD9833 + IRF4115 + Coils 3.3 miliHenr +- resistors 10KOhm :
The connection diagram when using pure ATTINY85 chip :
github.com/mcore1976/antispy-jammer/blob/main/arduino-mic-supresor-ultrasonic-v3-ATTINY85-TPA3116-IRF-coils.png
The source code to be compiled with AVR-GCC and uploaded directly to ATTINY85 with USBASP programmer :
raw.githubusercontent.com/mcore1976/antispy-jammer/main/main6-new-version5.c
keywords :
digispark attiny85 , microphone jammer , microphone suppressor , ultrasonic jammer , ultrasonic suppressor , provacy protector , speech protector , anti surveillance , anti-surveillance , ultrasound audio jammer , ultrasonic audio jammer , ultrasonic speech jammer , ultrasound speech jammer , ultrasound voice jammer , ultrasonic voice jammer , audio recording blocker . audio recording suppressor , audio recording jammer , anti spy jammer , anti spy blocker , anti-spy jammer , eavesdropping protector , eavesdropping blocker , protect private conversation , voice assistant blocker , voice assistant jammer , alexa blocker , alexa jammer , siri blocker , siri jammer , ultrasound noise generator , ultrasound noise jammer , audio supressor , wireless microphone jammer , wireless microphone blocker , zagłuszacz mikrofonów , szumidło , bloker mikrofonów , ochrona przed podsłuchem , ochrona przed podsłuchiwaniem , anty szpieg , ochrona przed nagrywaniem , sowa i przyjaciele , ochrona przed nagraniem , blokada dyktafonów , blokada mikrofonów , zagłuszacz dyktafonów , zagłuszacz mikrofonu . zagłuszacz dyktafonu, bloker nagrywania
#ALCHNL #attiny85 #arduino
มุมมอง: 1 229

วีดีโอ

Microphone Jammer update
มุมมอง 804หลายเดือนก่อน
Ultrasound Micrphone Jammer now jams iPhones ! Modified hardware includes high current Coils for resonance with Transducers. Also Mosfet transistor is used Project page : github.com/mcore1976/antispy-jammer For the setup : DIGISPARK TPA3116D2 AD9833 IRF4115 Coils 3.3 miliHenr resistors 10KOhm : New source code for testing : raw.githubusercontent.com/mcore1976/antispy-jammer/main/mic_jammer_digi...
Cloning my key and opening my garage gate with my 10 USD DIY CC1101 tool and Universal Radio Hacker
มุมมอง 20K11 หลายเดือนก่อน
Simple record & replay attack. This video shows how to use my DIY cc1101 tool in real world scenarios. I am using Universal Radio Hacker to find out what is data sequence used by my RF keyfob and CC1101 to replay key sequences. The project data is available here : github.com/mcore1976/cc1101-tool covering Arduino Pro Micro/ Nano / esp32 / esp8266 boards I made portable pen testing device with A...
DIY CC1101 tool - RF jammer, replay attack, sniffer - cheap & easy tool for radio pen testing
มุมมอง 46Kปีที่แล้ว
I decided to create cheap RF hacking tool with capabilities similar to Yardstick One. All the parts cost 10$ :-) The project page is here : github.com/mcore1976/cc1101-tool and... I am giving this design for free to everyone... Well, it is not Flipper Zero, it is even BETTER ! and still simpler to use than Yard Stick One The parts you need : (Sparkfun) Arduino Pro Micro 3.3Volts / 8 MHz version...
DIY microphone jammer beast for less than 30$, voice recording blocker with Digispark and TPA3116D2
มุมมอง 17Kปีที่แล้ว
Protect your privacy! This is the simplest and cheapest ultrasonic microphone jammer that you can build yourself! Yes, it jams even iPhones from couple of meters! check the project page here : github.com/mcore1976/antispy-jammer The jammer version that I am showing in the video uses 25kHz ultrasonic transducers ( "T25", 20 for 15$ ) , audio amplifier module with TPA3116D2 (less than 5$ ) and Di...
DIY the simplest off-grid packet radio communicator for secure messaging based on CC1101 and Arduino
มุมมอง 3.1Kปีที่แล้ว
This device works without any wifi / cellular network and allows two-way or one-to-many type of communication on selected frequency, modulation and encoding. Also encryption may be added. Range of this device strongly depends on the frequency & modulation used as well as the antenna and can be even several miles in open space in good conditions. For best results please use CC1101 modules with a...
One to rule them all - Crossplatform SDR decoder - SDRANGEL - short review and examples
มุมมอง 30Kปีที่แล้ว
This is the most beefy crossplatform SDR application with multiple decoding options. However it requires quite strong PC. Currently supports following decoding options : Analog - AM, APT, Broadcast FM, DSB, FM, NTSC, PAL, SSB, VOR Digital - 802.15.4, AIS, ADS-B, APRS, DAB, DAB , DCF77, DMR, dPMR, D-Star, DVB-S, DVB-S2, FreeDV, LoRa, M17, MSF, Packet (AX.25), Pager (POCSAG), RS41 Radiosonde, TDF...
Simplest, cheapest, effective DIY ARDUINO ultrasonic Microphone Jammer / DIY ultrasound Audio Jammer
มุมมอง 12K2 ปีที่แล้ว
[ENABLE CAPTIONS!] In this video I am showing how to build ultra cheap ultrasound Dictaphone / Microphone jammer to protect your privacy against unauthorized recording or eavesdropping during business meetings etc... Whole device costs less than 30 USD and is very simple. Please notice that commercial solutions giving the same jamming results cost 10-50 times higher and I am giving you this sol...
Easy multi frequency DIY RADIO JAMMER - CC1101 & Arduino Pro Micro - 10$ cheap wideband RF JAMMER
มุมมอง 61K2 ปีที่แล้ว
[ENABLE CAPTIONS!] I am giving you the universal RF jammer that operates within sub 1GHz RF range. It is constructed of Arduino Pro Micro ( 3.3V , 8MHz ) and CC1101 board. Total cost is below 10 USD, the output power is 10mW. All of the project details are available here : github.com/mcore1976/cc1101-jammer The jammer can succesfully jam car keys, wireless doorbells, drones and other devices th...
SDR++ ( SDR Plus Plus ) - first multi-platform / cross-platform free open source SDR radio scanner
มุมมอง 12K2 ปีที่แล้ว
[ENABLE CAPTIONS!] In this video I am presenting you SDR great and simple SDR application from Alexandre Rouma. This app works under Windows, Linux and MacOS. I am also doing Windows and Linux installation and briefly going through menu options. The SDR software offers most of features from SDR# (SDR Sharp) but runs on every operating system and is bloat-free (and faster!). I does not require s...
2$ Arduino mouse jiggler / mouse mover to prevent screen saver screen locking for covid home office
มุมมอง 4.9K2 ปีที่แล้ว
[ENABLE CAPTIONS!] If you work remotely using your company PC in Covid-19 times you need something that will keep your PC awake and prevent from locking the screen / locking the keyboard automatically while you're at home during teleworking. You want also to prevent changing your status from Online to Away in corporate communicators ( Skype , Outlook, Teams etc.). Here is the solution that cost...
Hacking PC with 10$ perfect BadUSB / Rubberducky / USB device based on Arduino Leonardo SS Beetle
มุมมอง 6K2 ปีที่แล้ว
[ Enable captions!] In this video I am showing the simplest way to create Malicious USB device that may be used for hacking/pranking Windows PC aka Rubberducky device. I am using Arduino SS Beetle here , micro Arduino Leronardo clone with Atmega32U4 chip (native USB device) which perfectly suits for such kind of malicious activity ( small, cheap and simple) - f.ex. you can make USB pranks. Once...
DIY Arduino LED news ticker / Digispark LED banner with MAX7219 / DIY LED scrolling message display
มุมมอง 1.2K2 ปีที่แล้ว
[ENABLE CAPTIONS!] In the video I am getting absolute MAX out of Digispark / ATTINY85 by constructing LED scrolling display with following features : - maximum 500 characters text for scrolling - support reverse mode ( right to left reading - Middle East guys) for Arabic, Aramaic, Azeri, Divehi, Fula, Hebrew, Kurdish, N'ko, Persian, Rohingya, Syriac and Urdu - text stored in non-volatile EEPROM...
OpenEar - banned RTLSDR app - DMR , TETRA , POCSAG, ADS-B, NX48, NX96, DPMR - one to rule them all
มุมมอง 30K2 ปีที่แล้ว
OpenEar - banned RTLSDR app - DMR , TETRA , POCSAG, ADS-B, NX48, NX96, DPMR - one to rule them all
Simplest, cheapest, effective DIY ARDUINO ultrasonic Microphone Jammer / DIY ultrasound Audio Jammer
มุมมอง 33K2 ปีที่แล้ว
Simplest, cheapest, effective DIY ARDUINO ultrasonic Microphone Jammer / DIY ultrasound Audio Jammer
Watch real terrestial TV (DVB-T) on your smartphone with 10$ RTLSDR USB dongle and 2$ AerialTV app!
มุมมอง 18K2 ปีที่แล้ว
Watch real terrestial TV (DVB-T) on your smartphone with 10$ RTLSDR USB dongle and 2$ AerialTV app!
Homemade high voltage paralyser, Taser, Stun Gun for 5 USD from cheap arc generator module in 30 min
มุมมอง 2.2K2 ปีที่แล้ว
Homemade high voltage paralyser, Taser, Stun Gun for 5 USD from cheap arc generator module in 30 min
DIY Ultrasonic pest repellent device for 10 USD / cheap and effective 40kHz ultrasound bugs repeller
มุมมอง 16K3 ปีที่แล้ว
DIY Ultrasonic pest repellent device for 10 USD / cheap and effective 40kHz ultrasound bugs repeller
DIY 30$ microphone jamming device, unauthorized audio recording protection - ultrasonic jammer
มุมมอง 30K3 ปีที่แล้ว
DIY 30$ microphone jamming device, unauthorized audio recording protection - ultrasonic jammer
hacking & clonning my garage key with URH ( Universal radio Hacker ) and ARDUINO DIGISPARK + FS1000A
มุมมอง 24K3 ปีที่แล้ว
hacking & clonning my garage key with URH ( Universal radio Hacker ) and ARDUINO DIGISPARK FS1000A
5$ ARDUINO car key JAMMER DIY. Relay attack / keyless car hack / car hacking protection
มุมมอง 67K3 ปีที่แล้ว
5$ ARDUINO car key JAMMER DIY. Relay attack / keyless car hack / car hacking protection
Improve your Internet speed - lock LTE band on any Huawei modem or router ( CPE , MiFi ) with HiLink
มุมมอง 16K3 ปีที่แล้ว
Improve your Internet speed - lock LTE band on any Huawei modem or router ( CPE , MiFi ) with HiLink
Radio hacking - setup of Raspberry Pi - installation of Raspbian, RTL-SDR, RPITX , static IP
มุมมอง 10K3 ปีที่แล้ว
Radio hacking - setup of Raspberry Pi - installation of Raspbian, RTL-SDR, RPITX , static IP
WIFI Man in The Middle Attack - how to create fake WLAN Access Point to hijack the communication
มุมมอง 14K3 ปีที่แล้ว
WIFI Man in The Middle Attack - how to create fake WLAN Access Point to hijack the communication
Poor man’s USB Rubber Ducky - 2 USD cheap USB Hacking Device based on Digispark ATTINY85
มุมมอง 7K3 ปีที่แล้ว
Poor man’s USB Rubber Ducky - 2 USD cheap USB Hacking Device based on Digispark ATTINY85
Tanie analogowe słuchawki dla graczy za 250zł/60EUR/70$ - Razer Kraken 2019 VS Roccat ELO X Stereo
มุมมอง 2.2K3 ปีที่แล้ว
Tanie analogowe słuchawki dla graczy za 250zł/60EUR/70$ - Razer Kraken 2019 VS Roccat ELO X Stereo
How to select or lock to any LTE band on any Huawei LTE router / CPE with smartphone
มุมมอง 45K3 ปีที่แล้ว
How to select or lock to any LTE band on any Huawei LTE router / CPE with smartphone
How to select proper LTE CPE / 4G Router for your home network ? What to check before you buy ?
มุมมอง 9303 ปีที่แล้ว
How to select proper LTE CPE / 4G Router for your home network ? What to check before you buy ?
Cheapest Analog & HDMI Video capture USB devices. Recording & streaming from Nintendo PS2 PS3 Sega
มุมมอง 1.4K3 ปีที่แล้ว
Cheapest Analog & HDMI Video capture USB devices. Recording & streaming from Nintendo PS2 PS3 Sega
DIY simplest LED TICKER - SCROLLING LED TEXT DISPLAY - that everyone can build ! ATTINY 85 + MAX7219
มุมมอง 2.4K3 ปีที่แล้ว
DIY simplest LED TICKER - SCROLLING LED TEXT DISPLAY - that everyone can build ! ATTINY 85 MAX7219

ความคิดเห็น

  • @adamkee97
    @adamkee97 19 ชั่วโมงที่ผ่านมา

    I have tested this using ESP32-WROOM32 with your example codes. It works like a charm. There are some errors here and there to smooth out and definitely a fun thing to experiment with.

  • @zibenziben7983
    @zibenziben7983 2 วันที่ผ่านมา

    W tym lapku 4 giga to nie aż tak mało. Widziałem Windowsa 10 na 2 gigowym kalkulatorze 😂. Masakra nawet youtube nie wyrabiał.

  • @kaichichow1049
    @kaichichow1049 2 วันที่ผ่านมา

    Hi, we have had success with the 25khz. The 16kHz one seems to make minimal / no noise at all (recording on an iPhone) - Any suggestions or ideas why? I thought the 16 would work best for iPhone, and the 25 for other phones

    • @justanengineer5599
      @justanengineer5599 วันที่ผ่านมา

      Finally I recommend only using 25kHz transducers. The lower frequency transducers are not suitable. The of course supress microphone sensivity but do not give the noise effect at suffcient level

    • @kaichichow1049
      @kaichichow1049 วันที่ผ่านมา

      Ah okay thank you. So no benefit of running both at once? I spent close to a thousand on the smaller ones 😂 may as well make use of them if they run better together. But seems like they don’t work (at all) How many 25kHz would you recommend for a small room to target specifically latest iPhone

    • @justanengineer5599
      @justanengineer5599 23 ชั่วโมงที่ผ่านมา

      at least 100 placed in different opposite locations like corners of the room

  • @Mohammed-de9sq
    @Mohammed-de9sq 4 วันที่ผ่านมา

    quick question, i have been working with rpiTX lately. The only problem i have is that the poweroutput with the RPI400 of mine is very low. Do you have any idea how i can boost this frequentie? especially for 433 MHZ. I thought about putting the gpio directly onto a 433MHZ transmitter but this does not work

    • @justanengineer5599
      @justanengineer5599 3 วันที่ผ่านมา

      connect a power RF output amplifier. There is a lot of them based on Quorvo 4 pin chips and they cost around 10-20 usd. Check on www.aliexpress.com

  • @drgoro9139
    @drgoro9139 5 วันที่ผ่านมา

    is it possible to jam a frequency range for example 90.10 to 92.50 ?

    • @justanengineer5599
      @justanengineer5599 4 วันที่ผ่านมา

      no. check video description and github page for precise frequency range that can be used

  • @TheFercho132
    @TheFercho132 6 วันที่ผ่านมา

    hi, I bought for mistake the module HC-12 insted the CC1101, can I make this project with that transmission module? (I bought the arduino nano and TXS0108E TTL logic convertr)

    • @justanengineer5599
      @justanengineer5599 5 วันที่ผ่านมา

      no this is only for CC1101

    • @adamkee97
      @adamkee97 19 ชั่วโมงที่ผ่านมา

      100% not. You will need another library for this specific IC with specific instructions...

  • @kermitinmountain6371
    @kermitinmountain6371 6 วันที่ผ่านมา

    Hi, I like to ask you a questions, do I need to add reset button in order for the data to be uploaded or not? Thank you.

    • @justanengineer5599
      @justanengineer5599 6 วันที่ผ่านมา

      no you just need to plug it into the PC

    • @kermitinmountain6371
      @kermitinmountain6371 6 วันที่ผ่านมา

      @@justanengineer5599 Thank you for the clarification.

  • @ergonomiczero2228
    @ergonomiczero2228 6 วันที่ผ่านมา

    How is this different than the evil crow v2?

    • @justanengineer5599
      @justanengineer5599 6 วันที่ผ่านมา

      it has only on CC1101 chip and you can connect it to your mobile phone. Moreover the components cost 15usd not 75usd

  • @zython6312
    @zython6312 7 วันที่ผ่านมา

    Also can it work at a range of 315 and 433 simultaneously if so how would I code it?

    • @justanengineer5599
      @justanengineer5599 7 วันที่ผ่านมา

      to frequencies at the same time is not possible. But quick jumping between these two frequencies is possible. See my other video about the jammer

  • @zython6312
    @zython6312 7 วันที่ผ่านมา

    Is it possible for to write code that has it operate at a range of frequencies like 430-440 at the same time

    • @justanengineer5599
      @justanengineer5599 7 วันที่ผ่านมา

      it would have to swipe between both frequencies. But yes it is possible

  • @zython6312
    @zython6312 9 วันที่ผ่านมา

    I have a m1101d here and it’s connected to my arduino nano. I am trying to program it to where it can be 315 MHz as it has a cc1101 chip and is able to do this according to seller. How would I do this?

    • @justanengineer5599
      @justanengineer5599 9 วันที่ผ่านมา

      there is a field in the code that selects the base frequency. Watch the video carefully

  • @tanvirulislam9759
    @tanvirulislam9759 12 วันที่ผ่านมา

    Hi! UNO boards have a 3.3V output pin, can i use UNO boards for this project? I tried searching in your github repo but there was no instructions about uno boards

    • @justanengineer5599
      @justanengineer5599 12 วันที่ผ่านมา

      uno uses 5v ttl logic so it is not good

    • @tanvirulislam9759
      @tanvirulislam9759 6 วันที่ผ่านมา

      @@justanengineer5599 if i use a TXS0108E TTL logic converter, can it work then?

    • @justanengineer5599
      @justanengineer5599 6 วันที่ผ่านมา

      yes. this one of the options. The other is to power arduino Atmega chip from 3.3V

  • @sebasscorrea
    @sebasscorrea 12 วันที่ผ่านมา

    Can this be modified to make it work as anti barking device?

    • @justanengineer5599
      @justanengineer5599 12 วันที่ผ่านมา

      of course. it works this way from the start. Pets will not stand this sound for a long time

  • @StadiaTrial
    @StadiaTrial 13 วันที่ผ่านมา

    Is it possible to go with 20khz from one channel of the amp and 25khz from the other channel to cover a wider range of mics? Unclear if the signal generator could handle this, but if you had two of them, could you feed each frequency to a different audio channel and amplify both at once?

    • @justanengineer5599
      @justanengineer5599 12 วันที่ผ่านมา

      single AD9833 generator has only one channel I am afraid. so the answer is no. you need 2 such devices

  • @adilsonmiranda43
    @adilsonmiranda43 14 วันที่ผ่านมา

    while ( !(USISR & _BV(USIOIF)) ) USICR |= _BV(USITC);

    • @justanengineer5599
      @justanengineer5599 14 วันที่ผ่านมา

      have you installed necessary files for Digispark in Arduino IDE ?

  • @adilsonmiranda43
    @adilsonmiranda43 14 วันที่ผ่านมา

    estou com erro nesse programa qaundo rodo trava com codigos

  • @TM-nq4tt
    @TM-nq4tt 15 วันที่ผ่านมา

    How does it receive the car key signal to relay to the transmitter?

    • @justanengineer5599
      @justanengineer5599 14 วันที่ผ่านมา

      you do recording with URH and then implement the sequence manually in Arduino code

    • @TM-nq4tt
      @TM-nq4tt 14 วันที่ผ่านมา

      @@justanengineer5599 I record with the transmitter urh programmed to it?

    • @justanengineer5599
      @justanengineer5599 13 วันที่ผ่านมา

      watch the video carefully. 2 or 3 times.

  • @AnthonyHighVoltage-hl8fq
    @AnthonyHighVoltage-hl8fq 18 วันที่ผ่านมา

    hey! i need help with my NRF905SE is there a way to make a jammer with it? radio? or dtv jammer? thanks

    • @justanengineer5599
      @justanengineer5599 17 วันที่ผ่านมา

      better use cc11xx modules. NRF905SE does not allow to fine tune the frequency and only works in packet mode

    • @AnthonyHighVoltage-hl8fq
      @AnthonyHighVoltage-hl8fq 17 วันที่ผ่านมา

      @@justanengineer5599 awww man alr i already got then thanks anyway!

  • @MatthewHartfelder-wb3lu
    @MatthewHartfelder-wb3lu 20 วันที่ผ่านมา

    I am trying to do this project with an Pro Micro 3.3v, but it sometimes gets hung up on cc1101intialize and when it doesn't it says "cc1101 connection error! check the wiring." I have triple checked my wiring and can't find any problems. Any help would be appreciated.

    • @justanengineer5599
      @justanengineer5599 19 วันที่ผ่านมา

      there must be poor contact between some pins. Try to solder the cables

    • @MatthewHartfelder-wb3lu
      @MatthewHartfelder-wb3lu 19 วันที่ผ่านมา

      @@justanengineer5599 They are soldered

    • @justanengineer5599
      @justanengineer5599 18 วันที่ผ่านมา

      If so, you may try to use next cc1101 board as something may be wrong with existing board

  • @az50056
    @az50056 20 วันที่ผ่านมา

    Thank you!

  • @Malwarekid
    @Malwarekid 20 วันที่ผ่านมา

    Hey can you write a code for d1 mini to jam 433mhz ?

    • @justanengineer5599
      @justanengineer5599 19 วันที่ผ่านมา

      you can port this code easily just change the pin number

  • @Dayz-dm2eh
    @Dayz-dm2eh 21 วันที่ผ่านมา

    what frequency do you use to block a radio signal the same as a human brain

  • @Dayz-dm2eh
    @Dayz-dm2eh 21 วันที่ผ่านมา

    hello Im new to electronics but once its all put together and wired up and has the right modules when you plug it in to a Mac should the windows the control the modules pop up and what frequency do you use to black a radio signal the same as the brain thnx!.

    • @justanengineer5599
      @justanengineer5599 21 วันที่ผ่านมา

      the brain can only be controlled by social media as tiktok, facebook, twitter, instagram. Thats the only way and moreover the most effective!

  • @Antoine-hr5zr
    @Antoine-hr5zr 22 วันที่ผ่านมา

    where to start to design a pcb for your project?..i heard about kicad, from the given diagram can we do

  • @gilangsatriaajie2824
    @gilangsatriaajie2824 22 วันที่ผ่านมา

    is this save for long term use?

    • @justanengineer5599
      @justanengineer5599 22 วันที่ผ่านมา

      you have to test it For sure it shouldn't be used 24/7

    • @gilangsatriaajie2824
      @gilangsatriaajie2824 21 วันที่ผ่านมา

      @@justanengineer5599 Is there some kind of additional circuit so that this jammer can be used 24/7?

    • @justanengineer5599
      @justanengineer5599 18 วันที่ผ่านมา

      I think the option to detect human voice via microphone and jam it only when detected is a solution for this

  • @Mehdisamadi-dy9tj
    @Mehdisamadi-dy9tj 22 วันที่ผ่านมา

    Hello Thank you for publishing such a code. The remote control data received by recraw (milisec) changes every time it is received (due to the security mechanism used). Any ideas for this problem?

    • @justanengineer5599
      @justanengineer5599 22 วันที่ผ่านมา

      use Universal Radio Hacker to see if it is a rolling code

    • @Mehdisamadi-dy9tj
      @Mehdisamadi-dy9tj 21 วันที่ผ่านมา

      @@justanengineer5599 Can I use the jammer mode (jam 1) and the receiver mode(recraw) at the same time? I want to make a rolling attack.

    • @justanengineer5599
      @justanengineer5599 20 วันที่ผ่านมา

      not. I would suggest to build two sets of this device and use them both at the same time

    • @mehdiboy-kj8fp
      @mehdiboy-kj8fp 12 วันที่ผ่านมา

      ​@@justanengineer5599I made two sets of this device (to carry out the replay attack). One in jam mode One is also in the recraw mode The problem is that the recraw receives the jamming frequency and not the remote control data Do you have a solution?

    • @justanengineer5599
      @justanengineer5599 8 วันที่ผ่านมา

      setrxbw is the command that you should use to narrow the receive bandwidth not to get the jammer signal. Read issues tab for the project. I have already explained how to do it for other person

  • @Antoine-hr5zr
    @Antoine-hr5zr 22 วันที่ผ่านมา

    hello really excellent work, it would be possible to also bring together all the small electronic elements like inductance, resistance etc... on one and the same cms plate for example which would re-connect the others like the amplifier..the random generator

    • @justanengineer5599
      @justanengineer5599 22 วันที่ผ่านมา

      yes of course. But the point was to create something that anyone can build from publicly available components not some customized board

    • @Antoine-hr5zr
      @Antoine-hr5zr 22 วันที่ผ่านมา

      @@justanengineer5599 yes I see..but when you opened the case in the video it looked like it was complicated to solder...you must have spent a lot of time ..

    • @justanengineer5599
      @justanengineer5599 18 วันที่ผ่านมา

      In fact it was 2 hours of work

  • @Optimuseq
    @Optimuseq 24 วันที่ผ่านมา

    Good for big company confidential conversations. "Everyone please place your smartphone on the table in front of you..... *click* and now we can talk" :)

  • @KingKunta-vn1sr
    @KingKunta-vn1sr 24 วันที่ผ่านมา

    Hello, how can i get a car remote jammer

    • @justanengineer5599
      @justanengineer5599 23 วันที่ผ่านมา

      I am afraid you need to build it on your own

  • @alirezaasad8822
    @alirezaasad8822 24 วันที่ผ่านมา

    😍😍😍😍😍😍

  • @emilluneberg6998
    @emilluneberg6998 24 วันที่ผ่านมา

    Have you seen Linus Tech Tips video from month ago on similar device from aliexpress, and how it compares to your build.

    • @justanengineer5599
      @justanengineer5599 24 วันที่ผ่านมา

      it is almost the same but my costs 10x less and everyone is capable to build it. the difference is that they may have battery built inside.

    • @bbglas007
      @bbglas007 2 วันที่ผ่านมา

      ​@justanengineer5599 he mentions paper or cotton will block the jammer and the microphone will record as normal. Is the same true for yours? If that's the case, a microphone pop shield may easily block this

  • @user-zc1ts3ks6q
    @user-zc1ts3ks6q 25 วันที่ผ่านมา

    Share Your Refer Link

    • @justanengineer5599
      @justanengineer5599 24 วันที่ผ่านมา

      youtube.com/@justanengineer5599?si=NtOFPVKL890ybVCZ

  • @SilvaD702
    @SilvaD702 25 วันที่ผ่านมา

    I've heard about this before. Very impressive to see it in theory

  • @irfan_antennas
    @irfan_antennas 25 วันที่ผ่านมา

    Please share link for buying inductors and diode. thanks

    • @justanengineer5599
      @justanengineer5599 24 วันที่ผ่านมา

      Inductors : www.aliexpress.com/item/10000000696126.html RECTIFIER DIODE (1N4001 or 1N4004) : www.aliexpress.com/item/1005004962400215.html

  • @DannyDawson-lk8ts
    @DannyDawson-lk8ts 26 วันที่ผ่านมา

    Holy cow your a genius ☺️sir me and my college friends really appreciate your hard work

    • @justanengineer5599
      @justanengineer5599 24 วันที่ผ่านมา

      I am not a genius I am just an engineer. This is just an example how to use the knowledge in practice. Knowledge is power.

    • @DannyDawson-lk8ts
      @DannyDawson-lk8ts 24 วันที่ผ่านมา

      @@justanengineer5599 wow sir amazing work thank you so much for your reply I will show my friends all your vids as well

  • @wendyhari7207
    @wendyhari7207 26 วันที่ผ่านมา

    are all ultrasonics transmitter or paired with receiver?

    • @justanengineer5599
      @justanengineer5599 26 วันที่ผ่านมา

      what do you want to pair it with? This device utilizes the effect that FM modulation of ultrasound leaks into audible band of the microphones

    • @wendyhari7207
      @wendyhari7207 25 วันที่ผ่านมา

      @@justanengineer5599 ok clear thanks

  • @nicoduwa6852
    @nicoduwa6852 26 วันที่ผ่านมา

    great video adam!! always enjoy seeing an update of this project!

  • @persianrogue4614
    @persianrogue4614 26 วันที่ผ่านมา

    i really enjoy watching ur videos🤩❤✌

  • @kadinbrasil8160
    @kadinbrasil8160 26 วันที่ผ่านมา

    Bom

  • @OGajodaForquilha-bn7we
    @OGajodaForquilha-bn7we 26 วันที่ผ่านมา

    what is the approximate range?

    • @justanengineer5599
      @justanengineer5599 26 วันที่ผ่านมา

      Depending on the device you want to jam and number of transducers. Can vary from 2 meters to 5 meters or more

    • @jackbaiatul9351
      @jackbaiatul9351 18 วันที่ผ่านมา

      I love it! I build one round with 140 transmitters. 12v 5a.i used Attiny85 usb. I work's 1m distance. Maybe need more amps. And it start to work after 8-10 seconds. I used one older code from yours too.

    • @justanengineer5599
      @justanengineer5599 16 วันที่ผ่านมา

      try to add IRF4115 mosfet, diode and bunch of coils. It increases the distance many times

  • @OGajodaForquilha-bn7we
    @OGajodaForquilha-bn7we 26 วันที่ผ่านมา

    great project!

  • @matzcontreras
    @matzcontreras 26 วันที่ผ่านมา

    What you need to do it?

  • @Micha-wr1px
    @Micha-wr1px 27 วันที่ผ่านมา

    Witam, mam problem z połączeniem do T-mobile. PPP nie działa. May 30 00:40:29 et-0989 pppd[33073]: sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x4dfa5fd5> <pcomp> <accomp>] May 30 00:40:53 et-0989 pppd[33073]: message repeated 8 times: [ sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x4dfa5fd5> <pcomp> <accomp>]] May 30 00:40:56 et-0989 pppd[33073]: LCP: timeout sending Config-Requests May 30 00:40:56 et-0989 pppd[33073]: Connection terminated.

  • @grahambennett3851
    @grahambennett3851 27 วันที่ผ่านมา

    When I use your universal CC1101 interactive tool my addraw and showraw displays as a single line across the screen whereas your video shows it as block of lines. Is there a setting I need to make in order to display in a block on the page and not one long line?

    • @justanengineer5599
      @justanengineer5599 26 วันที่ผ่านมา

      it will do one big line, at least for showraw

  • @petermarin
    @petermarin 27 วันที่ผ่านมา

    When you say you have to adjust your antenna to receive Adsb transmission, what do you mean? I’m not getting any adsb so not sure if I’m doing something wrong

    • @justanengineer5599
      @justanengineer5599 27 วันที่ผ่านมา

      I was using different antenna for Adsb. basically it was around 13cm long dipole as I recall. I had to replace antenna

  • @MikeMacKinnon-yc6md
    @MikeMacKinnon-yc6md 28 วันที่ผ่านมา

    Thank you for putting together these great videos. I am having some problems getting this working. My main issue is with URH. I do not see any signals. I've tried different Antenna's, I went through all the possible settings, I've changed everything. Adding and removing a low noise amplifier. But it must be.... that URH on my Windows 11 is not working properly. Because when I close the software, and open up SDR#, I can see all the signals on their respective frequencies.. my vehicle FOB (315Mhz), my weatherstation (433.92 Mhz) and my garage door opener at 314.6 MHz. Do you have any suggestions on how to get URH to be able to see these same signals?

    • @justanengineer5599
      @justanengineer5599 27 วันที่ผ่านมา

      yes. first you need to get windows working with your rtl sdr dongle. you may look for some of my old videos showing how to install driver with Zadig tool

    • @MikeMacKinnon-yc6md
      @MikeMacKinnon-yc6md 23 วันที่ผ่านมา

      @@justanengineer5599 Hey Adam, So I gave up on getting URH to work on Windows. I installed Debian 12 on an older laptop, and URH is working well on that. I am continuing to work on my Windows machine to complete this project. I am working on an ESP32 board. I have flashed the ESP32 with your .ino file for the ESP32 with no compiling errors. On my ESP 32 I can see a red and blue light lit steady (not flashing). I think this means I have uploaded it successfully. I then switch to Putty to communicate with your program. In Putty, I select the serial radio button, I enter my number for port COM# (in my case my device manager is telling me 5), speed I enter 115200 baud rate, data bits 8, stop bits 1, parity none, flow control none. When I open putty terminal. I only see a Green Square.. and not the (c) Adam Laboda.. any thoughts?

    • @MikeMacKinnon-yc6md
      @MikeMacKinnon-yc6md 22 วันที่ผ่านมา

      Okay, I changed my procedure a little bit. After Flashing the program, I press Enable on the ESP32, I disconnect the USB Cable from the computer.. wait a few seconds.. then plug it back in.. then open up Putty.. and it's almost working.. but the ESP32 keeps resetting over and over again..so I keep seeing your name roll up the screen along with.. (C) Adam Loboda 2023 ets Jul 29 2019 12:21:46 rst:0x8 (TG1WDT_SYS_RESET),boot:0x1a (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0030,len:1448 load:0x40078000,len:14844 ho 0 tail 12 room 4 load:0x40080400,len:4 load:0x40080404,len:3356 entry 0x4008059c CC1101 terminal tool connected, use 'help' for list of commands...

    • @MikeMacKinnon-yc6md
      @MikeMacKinnon-yc6md 21 วันที่ผ่านมา

      It works! It works! Thank you, Thank you, Thank you! Wow.. it only took me like 3 weeks to get this working! In the end it was a stupid mistake.. In the sample code you provided.. the XIAO chip is the code that isn't commented out and the WROOM code is commented out.. I switched this.. everything is up and running.. just tried jamming.. cause that was the easiest thing to try first.. man.. such a sweet project. Thank You! // defining PINs set for ESP32 module // Example for XIAO ESP32 C3 /* byte sck = 8; // GPIO 8 byte miso = 4; // GPIO 4 byte mosi = 10; // GPIO 10 byte ss = 20; // GPIO 20 int gdo0 = 21; // GPIO 21 int gdo2 = 7; // GPIO 7 */ // defining PINs set for ESP32 WROOM module byte sck = 18; // GPIO 18 byte miso = 19; // GPIO 19 byte mosi = 23; // GPIO byte ss = 5; // GPIO 5 int gdo0 = 2; // GPIO 2 int gdo2 = 4; // GPIO 4

    • @justanengineer5599
      @justanengineer5599 2 วันที่ผ่านมา

      I am glad you made it !

  • @SaadHassan-tr7yw
    @SaadHassan-tr7yw 29 วันที่ผ่านมา

    what is the effective range??

    • @justanengineer5599
      @justanengineer5599 28 วันที่ผ่านมา

      depends on the device you want to jam. For android phones 4+ meters for iphones half of it

  • @emilj.4766
    @emilj.4766 หลายเดือนก่อน

    😂😂

  • @zubairhanif7825
    @zubairhanif7825 หลายเดือนก่อน

    Its did not lock 5g band

    • @justanengineer5599
      @justanengineer5599 หลายเดือนก่อน

      you need to contact the author of this application and ask for adding this feature

  • @osekagorska2330
    @osekagorska2330 หลายเดือนก่อน

    Cześć, mega kanał! można użyć do tego projektu arduino uno? Akurat to mam na stanie :)

    • @justanengineer5599
      @justanengineer5599 หลายเดือนก่อน

      jeśli zasilisz arduino z 3.3V to moze sie uda. Ale polecam zakupić coś z USB i 3.3v logika TTL