วีดีโอ

Do you have a link for the tool you used to press the seal in?

Could you please tell me what is the optimal torque used to screw the valve cover and the front cover, and are all the screws for the valves cover has the same length or there is a short and long ones

How to make a cake video, you get all the ingredients you need, and then you put it in the oven… No one will learn anything from that

🙏👍

🙏👍

🙏👍

What diagnose system do you use? Xentry? Thank you very much

There is no way those six exhaust bolts came off the exhaust down the back with a powered ratchet and without heat!! ;-)

nice video amigo

How much would this repair cost?

ist that w205?

Honestly I enjoyed this video, l learnt something new from this video

Do you need to put any grease on oil cooler seals? Or any O-rings of intake or EGR?

Great video thank you. Currently I am looking at a used 2014 glk350 with 90k miles and a 2017 glc300 with 109k miles. Which of the two engines is the more reliable with good maintenance of course?

How one should one prevent the following? Replacing the thermostat, always using premium gas , change oil in time.. Or is the following an issue with the design of the engine?

thas what we call restauration all old junk mercedes need repairs in engines..

Good ,but it is missing the removal of the adjuster and the tensionner ,someone else did for you or yu hide it?

How can i get the M271 EVO engine manual? Pls

Жоғары деңгейде жинайды екен моторды маған ұнады 👍👍👍👍🇰🇿

May be a dumb question but is that pressure enough to bust a brake line??

This is the dumbest s*** I've ever seen what a waste of time

Когда на машыну устанавливаеш

You didn't show how to diagnose it

I have a 2016 GLC 300 need timing chain replaced. Has80000 miles but BNZ refuse to repair warranty because I did not service the vehicle from authorize service center. Now it parks in my driveway. Diagnostic fault code P03400.My question is where is the broken timing chain? was it fall inside homeware's that can damage the engine? After replacing the chain what kind of issue I may going to have? Please answer.

Buenas tardes Do you know where I can get the differential cover of a Mercedes Benz 190E of 88?

Just put in seal dry correct no dielectric grease ?

Please, why did you overhaul the differential, what were the symptoms? Me on my w210, manual transmission, when I shift gears there is a knock at the back in the area where the differential is located, what do you think could be the problem?

Hi master, a W204 C180, at 124000km After replacing the chain, the noise remains and starts after 3 times. I would like to know how is it possible to correct the problem ? Thanks in advance for watching the starting video. th-cam.com/video/qBpRkln74x8/w-d-xo.html

How many pounds of torque?

How many pounds of torque?

What’s the torque for the Cam phasers?

It’s impossible to purchase one of these in the UK now 2024. Mercedes does NOT want know 😔. I have a beautiful 211 that I’m going to have to scrap due to this fault. Thank you Mercedes for this DANGEROUS design fault & your disgraceful customer care 🤮

I have rattle only at worm start after hour or two restart the engine no codes on scanner or engine light. th-cam.com/users/shortsRn2kAqdp2ZA?si=LO2LjLV3lat_JkS4

The most important part is missing, how do you remove the panel.

I really like the video but the m271 is trash compared to m111

WHY DIDN'T YOU REPLACE CHAIN GUIDES ?

I installed a new chain, phasers, used the cam alignment tool, installed a new tensioner, and I released the tensioner properly. Everything lined up perfectly. I get code P0017, Cam position sensor bank B, changed it and still there. I heard somewhere that the exhaust cam mark needs to be a line off/tooth off from the housing arrow mark. Is this the procedure that needs to be done when doing the timing chain job?

اخبرني كم حجم ورق السنفره المستخدم بداية الفيديو

After the new camshaft gear bein put and all the marks are correct. what do i need to do after tightening the Camshaft gear ?

Very bad done!

не все показано, много важных деталей разборки нет

Can you share the torque for the valve cover bolts?

You skipped the MOST critical part, how you installed the timing tool and how you matched the timing marks

What the torque setting for the Camshaft gear?

I have 2 question for you. Where is gauge transmission oil and I have à trouble With my transmission

Would take me all day to get to 2:30

there's no need to change the crankshaft gear too? doesn't it get damaged by the loose chain?

there's no need to change the crankshaft gear too? doesn't it get damaged by the loose chain?

Man you got me F’ed up this is bank 1 not bank 2

Bullshit video. DO NOT FOLLOW HIS INSTRUCTIONS...which he provided 0 instructions anyway. He didn't even TIMED IT CORRECTLY OR SHOWED HOW TO LINE THE UP THE TIMING. GARBAGE 🗑️ VIDEO.