วีดีโอ

2 момента: Не пытайтесь производить регулировку уровня по пузырьковому - там погрешность 0,5 мм/м - лучше по отметкам на расстоянии от 5м. из 3-х положений - левый, центр, правый, конструктив просто отличный, разборка, регулировка не занимает много времени. У самого PLS 90 - отличный аппарат. Всего наилучшего.

The newer ones you can get a rounded headache rack, and i like the look of a rounded that the pointed ones like that.

Di😊 ciekawe🎉🎉

Let's also thank youtube for letting you bring this story to us.

So they keep all their leaves? Or do they go into hibernation? I have 2 from seed in Portland and this is their first year. Both look healthy. Its starting to get pretty cold at night, and I'm planning on getting some plastic to create a small green house with car window reflectors.

When this happens i just resod

Genius! Absolutely genius! Thanks for sharing with us all.

this is like solving a puzzle ... if i were a theif, and i AM, i take this as a challenge... it can be solved with a piece of steel and a hammer, break the lock and get in.

This is just impressive to me!

Great tutorial, thanks for sharing it.

I have a 650b it goes forward and reverse only for a couple if minutes

I have an older 2003 Terex TX 650. Do you recall if the transmission uses the same motor oil as the motor?

Or battery sawzill through latch rob lpl

Lol break that lock with two screwdrivers😊

Doesn't block a pick or a flat head and a hammer

The cutting torch has entered the chat.

Pick that lock in 8 seconds...

Number one for advocados is they need good oxygen penetration into soil to prevent root rot. I’ve got mine in 30% peat moss, 30% perlite, 30% pumice, and 10% sand with a thick compost layer ON TOP not mixed down and off the trunk a bit and they are growing like crazy.

Can you provide the link to the parts you used. I tried looking for OX Attachments and AUX Attachments on eBay, but couldn't find it. Also, how did you know this part would fit your JD 27D?

I have a TX640 and forward and reverse work fine but the trans disconnect button on the loader control doesn’t work. When I push the button, the relay clicks, but I don’t know where the wires go from there. I was hoping they went the same solenoid in this video but since the forward and reverse work, I know the solenoid is fine. Any advice form the people who see this video would be appreciated!

Just FYI don't get the plastic ones where you hook the wiper arm too they will fail and come off easy. If you can find the all-metals construction one get those. You will thank me later.

How much was it

You get a thumbs up and a comment to help the algorithm for keeping the silence in your vid and for not laying down some god awful music. Bravo, sir! Enjoy your LMTV, I might be picking one up soon.

do you have an update on this tree? maybe you can use the seeds to make more cold hardy babies

[great, looking bull dozer]👍

Can you still use your thumb with the tilt bucket ?

Grease that thing! 😂

I think you should pressure wash your pressure washer.

Hey, good tips bruh!

Should have left it real time.

That is genius!

Brilliant.

Thanks for the video! I'm considering this same thumb kit. How is it working out 2 years later?

I love the Mongo bucket I got for my 50g, however I had to shorten my lines before I could use it.

Technically not an LMTV, but very cool video nonetheless.

Thanks for posting this video, very helpful in troubleshooting this device. However my problem is different, the bottom horizontal laser does not come on, only the top vertical laser. Can't find any information online correcting or diagnosing this issue. I have the device apart and all the fine copper wires look intact, I've been using your video for comparison.

Sounds like maybe moisture and water could have killed the trees, as in the winter the water doesn’t evaporate as fast. On that slope sounds like it’s given it drainage and protection from the cold winds. If you try another variety, try the fantastic (del rio) it hasn’t given me much issues it’s okay with dealing with water logging than the other varieties, and it seems like it’s more cold resistant. I love the Joey! It’s proven to be a fighter in my experience. I like the trees performance so much I have one in ground. And purchased another yesterday, and I have it in a pot with great drainage and soil that doesn’t hold as much water. Cactus soil, when I transplanted it, the soil that it came with was soggy and a lot of roots were dead and the plant seemed to have symptoms of root rot, but I’m hoping it’ll recover

What about this tree in 2024 ?

thank you. just bought an Owari, on its way soon. excited to put these tips to use

Thanks man. This will come in handy. I have a 1083

That sucks! Hopefully that doesn’t happen a lot .

Thanks for the video!

I have a fermec 650B not going into forward or reverse. Going to try the troubleshooting tips from you and the comments. Also, having trouble finding parts. Any good sources for parts support? Thanks for posting!

I have a Terex TX650 not moving forward and reverse. I've confirmed the solenoid valves move when the forward and reverse pedals are depressed. I have a feeling there's no hydraulic pressure to the valve for the actuator to do its work inside the transmission. What provides hydraulic power to these solenoid valves. I don't think it's the hydraulic pumps for the implements. Bucket at front and gantry at rear still work. Is there a pump inside the transmission? One of the hoses form the valve goes to the transmission, looks like a return line.

you can wash those out with soap and water

I fucking hate dealing with tracks on excavators

I'm seeing no cleaning of parts and everything put back together with dirt and no extra grease. That's probably why you're having so many problems. Just a thought. You can put all the new parts together you want, but if they're dirty on greased it does you no good whatsoever

Thanks for the video. Great information. The magnet on mine had a thin metallic layer that pealed up and interfered with the level. I use a small screwdriver with a round magnet on it to pick off all the pieces. Works as it should now. Mine is "Assembled in the USA", from 2007.