- 128
- 1 514 062
Rspec Nick
เข้าร่วมเมื่อ 25 พ.ค. 2013
Follow me as we do some vlogs and mess with some cars ✌
Should you buy a 1990s Project car
What's up all,
Today we are going to get into the pros and cons of messing with a 90s car vs just buying a newer car.
Today we are going to get into the pros and cons of messing with a 90s car vs just buying a newer car.
มุมมอง: 95
วีดีโอ
The Civic Hatch gets a JDM heart
มุมมอง 134หลายเดือนก่อน
What's up guys, In this video I'm doing a brief breakdown on what all was entailed in swapping from a D15B7 to a D15B non vtec motor.
How to change Oil filter housing gaskets on a 2003 to 2012 BMW X3
มุมมอง 5413 หลายเดือนก่อน
Welcome back everyone, Today we are tackling the oil filter housing gaskets on the N52 07 BMW X3 3.0. below are the tools and torque specs for this job. Tools Needed: T27 Torx bit (air ducts) T45 Torx bit (power steering reservoir) E10 reverse Torx socket (oil filter & water cooler housing) E12 reverse Torx socket (alternator) 1/4 inch rachet 1/4 6 inch extension 1/4 8 inch extension 10mm (wate...
How to change Spark Plugs & Coil Packs on a 2003-2012 BMW X3
มุมมอง 1924 หลายเดือนก่อน
Happy Weekend Everyone, Today we are changing the remaining ignition coils and spark plugs in this 2007 BMW X3 3.0SI. I did make a error when I was talking about the headlight bulbs they are low beams only. So H7 bulbs for the Low beams. This procedure should work for all X3s from 2003 to 2012. Later models may have a slight variation in the steps but should remain fairly the same. Below are th...
How to change ignition coils on 2003-2012 BMW X3
มุมมอง 1264 หลายเดือนก่อน
Good Afternoon Everyone, Today we are tackling a BMW issue with Misfires. this will relate to most of the P300 codes you will get from your BMW. This Ignition coil replacement also will carry into other BMW models but for this video I just labeled it as a X3 coil replacement as I had no other BMW to refer too. All parts were picked up from Advance Auto for $82 for 1 Ignition coil. if you plan t...
Genesis Coupe 3.8 is getting a built motor
มุมมอง 4994 หลายเดือนก่อน
Happy Weekend Everyone, in this video I'm am answering some of the most asked questions I've had on my 2013 Hyundai Genesis Coupe 3.8 Track. Hopefully these answers can help along with my plans for the car for the future
The Subaru SVX returns to the channel
มุมมอง 1985 หลายเดือนก่อน
Good Afternoon Everyone, I've gotten alot of questions regarding the 1992 Subaru SVX. So hopefully this video can answer those questions. If there was a question you had on the SVX drop a question in the comments and I should be able to answer them. If you are a fellow SVXer or are just curious on following the progress with the car or cars smash that subscribe button and follow the builds.
JDM D15B EG Honda Civic Hatch
มุมมอง 1706 หลายเดือนก่อน
What's up everyone so today I'm finally introducing the 1992 Honda civic DX hatchback tot he channel. I got this car about 2 months ago and I've made a ton of changes to car and wanted to show you guys the car before I made a ton more. definitely stay tuned for the Civic content.
150cc GY6 performance upgrades (More parts for the Vento style 150)
มุมมอง 14Kปีที่แล้ว
Hello Everyone we are back at it once more with some fun filled scoot vids. Today I'm breaking in to more parts for the 171cc built GY6. See below for the parts and links. Thanks for watching and like always don't forget to smash that subscribe button. If you Use the links drop them a message saying Rspec Nick sent you from his TH-cam channel 👌. Front Brake Pads (Vento Style 150cc Scooters) www...
How to replace a dodge Dakota 3.9 Magnum EGR Valve and Coolant Temperature Sensor
มุมมอง 3.2Kปีที่แล้ว
what's up everyone today we are getting down the with dirty dodge. The 95 3.9 magnum dodge Dakota needs a new EGR valve and coolant temperature sensor so today that's exactly what it's getting. see the links below for the parts needed and the tool list. Tools Needed 10mm Socket 1/2 Socket Rachet 1/4 or 3/8 Optional Scraper Brake Clean EGR Valve by WVE www.rockauto.com/en/catalog/dodge,1995,dako...
GY6 Taida 172cc gets more upgrades
มุมมอง 688ปีที่แล้ว
what's up everyone today we are doing a quick update video on the current 150GY6 Build. so far we have taken it from stock to a 172cc Taida setup with cam along with the 28mm Kehin carb. now we are adding more fun to it with the NCY Super Transmission Kit V2. Along with the NCY Decompression tube. below are the links for the needed parts and like always shoot me a comment with any questions you...
The Scooter Gets a 171cc Big Bore Kit and 28mm Slide Carb from Rolling Wrench/Taida
มุมมอง 8Kปีที่แล้ว
What's up everyone it's Power days for the little GY6 150cc scoot. Today we are doing a walk around with the freshly redone Yamati Strada scooter. It currently has the below specs and is a day and night difference in power vs the stock 150cc configuration. also all links will be below the spec list. Thanks for watching everyone and if your not already smash that subscribe button for more conten...
Upgrading the GY6 150cc Cooling Fan
มุมมอง 3Kปีที่แล้ว
what's up everyone today we will be upgrading the GY6 150cc scooter with better cooling with a cooling fan that works. See below for the needed tools for install and the link to the cooling fan from unique performance. Tools Needed 8mm socket 1/4 wrench optional blue loctite Link for the Upgraded 150cc GY6 Cooling Fan www.ebay.com/itm/173969952644?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=...
The GY6 150cc gets it's first mod
มุมมอง 462ปีที่แล้ว
hello everyone in this video we are installing the first mod to the scooter the GY6 Air Scoop. Along with a run down on the plans for the Yamati Strada. below I posted what you will need for install as well as the link to the gloss black Air Scoop. Remember if your fan cover does not have 3 Pre-Drilled screw holes it won't sit correctly. Needed Tools Phillips Screwdriver 3 Cooling shroud screws...
Bought 3 150cc GY6 scooters for under 500 dollars
มุมมอง 622ปีที่แล้ว
What's up Everyone in this video we are doing a quick swap rundown on the 3 scooters I got for under 500 for all 3.
2005-2009 Mustang GT front rotor and pad replacement
มุมมอง 813ปีที่แล้ว
2005-2009 Mustang GT front rotor and pad replacement
Subaru SVX upgraded mounts (Motor,Trans & Pitch mount)
มุมมอง 106ปีที่แล้ว
Subaru SVX upgraded mounts (Motor,Trans & Pitch mount)
How to install front struts on a Dodge Dakota/Ram
มุมมอง 3Kปีที่แล้ว
How to install front struts on a Dodge Dakota/Ram
How To Replace Transmission Cooler Lines On A Dodge Dakota
มุมมอง 24K2 ปีที่แล้ว
How To Replace Transmission Cooler Lines On A Dodge Dakota
How to Install rear struts on a dodge Dakota
มุมมอง 1.9K2 ปีที่แล้ว
How to Install rear struts on a dodge Dakota
The Genny never disappoints #fyp#foryou#cars#Rspecnick#follow
มุมมอง 5262 ปีที่แล้ว
The Genny never disappoints #fyp#foryou#cars#Rspecnick#follow
How to replace your Idler pulley and tensioner pulley on your dodge Dakota + removing valve covers
มุมมอง 2.5K2 ปีที่แล้ว
How to replace your Idler pulley and tensioner pulley on your dodge Dakota removing valve covers
How to replace Spark Plugs and wires on a dodge Dakota
มุมมอง 6K2 ปีที่แล้ว
How to replace Spark Plugs and wires on a dodge Dakota
Replacing the front brake rotors,pads and Calipers on a (91-96) Dodge Dakota
มุมมอง 8K2 ปีที่แล้ว
Replacing the front brake rotors,pads and Calipers on a (91-96) Dodge Dakota
How to replace Air filter,PCV valve and Air breather on Dodge Dakota
มุมมอง 2.2K2 ปีที่แล้ว
How to replace Air filter,PCV valve and Air breather on Dodge Dakota
How to install new tailight assemblies and tailgate supports on 1991-1996 Dodge Dakota
มุมมอง 5182 ปีที่แล้ว
How to install new tailight assemblies and tailgate supports on 1991-1996 Dodge Dakota
How to install a new stereo in a Dodge Dakota (1991-1996)
มุมมอง 8K2 ปีที่แล้ว
How to install a new stereo in a Dodge Dakota (1991-1996)
Thank you, excellent step by step for ballast replacement 👍
Yap yap yap
Ive been watching all the Dakota videos but i missed the wiper motor and cold air intake somehow? Did they get taken down?
Just a quick question....I didn't see the need to take off the hose and disconnect the sensor? It seems like it would be easy enough to just take out the star screws and move the box to the side and put the new filter in?
I did this job once when I was in college because I couldn't afford to take it to the shop... pain in the ass. WHY did they EVER think integrated hubs were a good idea? I'm trying to get it back on the road now and I am dreading the brakes. The rear drums have NEVER been changed....
What happened at the end with the grinding 5 - 6 ?
Someone put a new radio in my dads 95 dodge before he got it but it’s very staticy on radio and aux could that be on the ground cause I just put all new speakers in it and it’s still staticy wondering if it’s that or antenna maybe
So where's the link?
Sir you were using the pulley bolt to move the tensioner. You got lucky it didn’t loosen. Your supposed to use a 19mm 12 point socket on the inverted torx that’s next to the pulley
Get a 2013+ and you’re golden
Oh is that scooter have the 50cc or the 150cc
Is the bed easier than dropping the tank..
so you didnt replace the lines, that we can tell.
i don't know if i'd want him working on my breaks
.......what chatter? I honestly couldn't hear a difference when inside the car. Sure the engine bay may be louder, but it's not any different than the sound of chain-slap these engines get after 100k miles.
@inorite4553 definitely has chatter compared to the dual mass from factory. Car got the clutch at 65k miles well below 100k it's a common thing to get gearbox rollover from a 1 piece flywheel.
Hey what’s all that what you’re working on called I got a 200cc gy6 engine and I’m new to all this and I want to know all that area you’re working on all the way to the gears in there and chain mine is screwed and I need to know cause I need to replace it
@@jaysins200cc the transmission kit? What parts do you need called out it's mainly just a variator and clutch along with the bell housings.
$50 in 2024 lol
I love This Car 😮... Quítale el Silenciador
I have a 2016 Coupe with the 3.8 and seriously, I haven't experienced any of these problems. Don't know where you live of what type driving you do but honestly, I haven't had any problems or trouble of any kind with mine. I live in Georgia and drive this car like it was meant to be driven, so I really can't speak to these issues. Maybe I just got a good one for a change.
Dang I wished I seen this before would have saved me about $700 I had a mechanic change that with doing a coolant flush and he still wants me to come back and change the fan as it's not operating at 100% which in turn is keeping my AC from running cold and my car overheating when in idle. Def could have just bought the part and bring it to him and pay for labor which he charged like $200 for smh! He got me good! Does that site you got the thermo from sell cooling fans?
Hey did you have original h pipe? Or what?
Anyone else’s slip yoke jus break ?
Bbs?
ESR
What rims are those
Esr SR01
kinda exactly how i want my to look , WHAT touch screen did you fo with ?
I went with a ebay one that was like 130 bucks but I'd strongly recommend against it I plan to swap it for like a pioneer or a Kenwood touch screen. The current one just lost the ability to connect to bluetooth.
What’s your wheel specs?
Front 19x9.5 +22 Rears 19x10.5 +22
not liking the wheels choice but eager to finish watchingthe video! keep grinding and i also make videos as well!!
I wasn't too fond of the color scheme on the wheels either but I do like the Work Miesters. I might actually have them re powdered
TTTUURRRDDDD😂😂😂😂😂😂 JUSS PLAYIN MY NINJA......CCCCOOONNNTTTAAAACCCCTTTTT
Great video!
Washers where you put the bolt for the exhaust would provide more clearance
When working with springs I always wear eye protection.
I need a windshield for a 93
@@AwwSSnap I think Safelite actually sells replacements but I don't think they have the windshield trim anymore
@@RspecNick those are priced up over $1000 I’m looking for cheap used ones
@@AwwSSnap that's probably on par with a used one. Most svx guys hold onto there parts cars like it's gold
Why go trough all this headache time and money and just go buy a new 150cc bike by the time u spent all that money into it it be close to the cost of a new one
@@Smodlee I had 3 alittle after this video was made. I was bored so I wanted to see what all it would actually take and the budget it would cost.
Never hear of a stat-er😂 😂 it’s pronounced State-er
Hey man, one of my heater hoses was leaking, i put a new hose on it, and ran it for a few minutes with no leaks, thought it was fine. Drove it next day for 15 20 mins and all the coolant blew out of the overfill on the coolant tank. Hoses seemed fine. My old lady also said her heat wouldnt work during that time. Does that sound like the thermostat to you?
@@AcidxAnarchy sounds like air was still trapped in the cooling system causing it to blow excess pressure into the overflow tank. That's based off knowing you just swapped a hose. If it happened before the hose replacement I would say possibly thermostat but with the hose just being replaced high chance air was still trapped in the system causing excess pressure.
@RspecNick do you think air in the system would cause the heat not to work, tho? Maybe it blew all of the coolant out before it could get hot enough to get to the heater core? I would hate to change thermostat if it's just air in the system ya know?
@@AcidxAnarchy yes air in the system can cause all sorts of issues. Especially if that's happening right after you changed the hose it's more then likely air trapped in the lines. You did bleed it after the hose install right?
@RspecNick no I did not, I wasn't aware I needed to when I did it. I haven't run it since then, and I've been researching more into the matter.
Looking really good!
@@sehismith thank you there's more to go yet
We just saved 200$ dollars just sittin here and doin this
@@vipersquad3 Easy money saved
Hey I did the air filter replacement, but the part that you called a “carbon bag” is dirty. Do you know what part I should look up for it to replace it ?
@@faithwashington1530 I do not know it unfortunately I tried looking for it when I did the filter and I never could find that bag I'm guessing it might be a dealer only item which is order item. They may have even completely redesigned it to remove that cause most cars don't have that bag.
Where did you buy this blue indicators on the dashboard?
@@jestemadrian4106 the evo prosport gauges?
Where did you buy electronic indicators on the dashboard this 3 blue once ?
@@jestemadrian4106 prosport evolution gauges 52mm.
Does these upgrades really run at 80 mph?
79mph with GPS if I tweaked gearing alittle it would be over 80
Take out the baffle muffler bro
looking good man how do you like the nibbi carb I just got it but I am trying to figure out the jetting
I have the kehin carb and the nibbi intake tube. I don't mind them tho the carb is definitely snappy
Excellent 👌🤪
Thank you, sir. All I needed.
Glad it could help
How is it holding up?
Holding up great honestly
I have the exact same scooter this is the first video I've seen with the scooter
The tao tao bws series? It's just a Yamaha Zuma clone from the Chinese market.
@RspecNick yes over here a local scooter company rebrands them as rougestars
@@dareallevi515 they are a decent looking scooter for sure
Most helpful video I needed. Thank u
Glad it could help
Hey i sent you a dm
Most common is rod knock don’t buy one !!
Crap quality control and garbage bearings