วีดีโอ

Great video, just to clarify, you still have confidence in this method adding marine antifreeze with the drill pump without running the motors works fine as long as i take out the plugs and cover with a rag before starting in the spring? Also, don't run the motor for more than a minute. Is there anything else i should do different ? Thanks

I watched this to completion. Very good video and If I was 20 years younger I think I’d give it a try. Thanks.

Nice T shirt. Been up tp Northern Outdoors a few times. In fact heading up to Maine this weekend to winterize my Sea doo.(from Florida). Great video.

Nice video. My daughter just got a quote of $572 for this while some warranty work was being done. Crazy.

Thank you man. The same thing happened to my house too and I was trying to reuse the tile. It’s a nice video.

Most excellent video. Thanks! Unfortunately, I won't have the patience or small nimble hands required to do this for my sister. Now I remember why my first Subaru (89 XT) was my last Subaru. This is a ten minute job on any Honda. I could do all 16 plugs on my Hemi in as much time with far less aggravation and be good for 100k miles.

youre thermostat is not open...... and you can fog threw the intake till the motor chocks out

What product did you use for fogging?

Just replaced mine today using your video. Perfect! Thanks

No anti- seize on NGK plugs, not required with NGK spark-plugs; also anti-seize compound can give you false readings if using a torque wrench. Also you’re spreading anti-seize compound with your bare fingers, you’re an idiot because it’s a carcinogen. The spark plug should be torqued to about 14 foot pounds into an aluminum head if possible, if a torques wrench not possible (tight space) then about a half a turn after it bottoms out to crush the spark-plug gasket.

Well, it looks like it is $76 dollars now. Looks easy enough, but I would probably get the cheaper part--if it is like a fan blower motor in my corolla, a cheap part will last a couple of years. Thank you so much for sharing this. My friend has a 2007 freestyle he is about to trade, but he was delighted that he can turn the annoying fan off.

Well, it looks like it is $76 dollars now. Looks easy enough, but I would probably get the cheaper part--if it is like a fan blower motor in my corolla, a cheap part will last a couple of years.

Thanks so much for making this!

Thanks for the video I'm having ti do this soon can't wait to fix all those symptoms you described match mine perfectly

thanks for the effort, - not I know how I would NOT do staining.

I keep having water leak from bottom but can't see why it is leaking

So very helpful. Very neat job. Thanks for sharing.

My hvac on my 2006 started going loco yesterday. This morning all was good but by the time I drove home it decided to go fast, slow, off, and nothing i pressed on the screen work. Got home and stopped all together. No light no fan nothing on the hvac. I am assuming it is this part unless someone says otherwise.

Does anyone know if a Ford Explorer bumper would fit a freestyle?

Great video! The only thing I would have done differently is NOT use any anti-seize on the spark plugs. This could cause over tightening/torqueing of the plugs. However, great info on the tools needed as well, I'll be doing this soon on my 2020 OB XT.

Well done, dude! Looks like it was a challenge to reach everything...

can you stain first?

Great video brother I’m doing mine this week.

Excellent video!

This is retarded - why would they design it like this, knowing that a serviceable part on the maintenance schedule?

At 10:31 you placed a clamp around the housing. What's the exact name for that housing? I am replacing my Century 3/4 hp pump and need the housing as well. I can't find anything on the internet that resembles that housing. There's no markings on my existing housing. Thanks.

I'm currently working on a project just like this. When I took the tiles up, none of the old thin-set was attached to the tile. Definitely, a pressure issue?

damn! That thing is a bear to get out...I finally just removed the front seat and it was much easier to squeeze in there and get to the resistor.

Wish this worked for a 2020 Forester...that driver side rear doesn't have enough slack in the harness to pull the boot out, and trying to disconnect that coil from the harness has me defeated, at the moment. 3 out of 4 done but I can feel that the engine isn't enjoying the lopsided ignition.

I have a cane-backed rocker that needs replacing but trying to figure out how to put the new webbing on. It's not stapled or anything to the back; just wrapped around top and bottom of back of chair. My question is does anyone have an idea how to get the webbing to be secure enough that when I lean back in chair it won't come undone? I've never tried this before but my current webbing is really falling apart with no back support and I need to replace soon. Thanks!

After putting in your Spark plugs did your motor shake.

loved the stain matching element. what was the cost of materials? what was the cost of the repair?

Never use staples

What about the oil valve you never mentioned if its suppose to be in or off??

really???? dude this is like the worst work ever!!!!! you should do it line by line not to staple it and glue it! REMEMBER WHOEVER STAPLE AND GLUE THIS KIND OF WORK IS COMPLETE BEGINER AND BAD WORKER!!!!!

Hi from Kissimmee, Florida. I have a beautiful dining room table and 6 chairs with wicker backing that my dad bought in 1971, when I was 6, in Daytona Beach, Florida and the table and three of the chairs will look wonderful. The set was made by American Furniture Company in Martinsville, Virginia. I found a place that will replace the wicker backing of my chairs for $150 per chair. I thought that was a lot, but now I see why! So, after I watched this video, I bought the kit that Todd suggested from Amazon and I hope I can do it myself. I just started this earlier today because my wicker backing kit just came in the mail. MY chairs do not have that thick piece around the edge that Todd's chairs do and I am having a lot of trouble getting this edging off. I have tried several tools, but it is going to take some effort. I think the easy part is going to be putting the wicker backing ON once I get the spline OFF! Any suggestions would be appreciated. Also, if you know where I can find antique American Furniture chairs , I would love to check it out because I can't find the exact chair. Thanks so much.

Thank you for this full tutorial video! It will come in handy for my husband and I this summer when we redo the retan in our dining room chairs

Not checking gap or did I miss that step I confirm all gaps

Spark plug replacement should never be this hard. Sorry...no Subarus for me.

what do I need to do to de winterize? just flush it out with water?

Thanks for the really helpful video.

I've always been told to disconnect the battery before doing these types of jobs. Is this correct?

What the name if your cutter tool?

Is the procedure the same with the forester?

Getting my spark plugs in at orielys tomorrow. Cant wait to do this on my 2021 60k outback xt

Excellent and smooth explanation of how to replace a pool pump

So you leave the treated gas in over Winter and instead of drain gas

Just a heads up here... Tighten the spark plug finger-tight until the gasket reaches the cylinder head, then tighten about ½ - ⅔ turn more with a spark plug wrench. (Taper seat you go about 1/16 turn more... These are way to tight.

Just a critical warning for newcomers, DO NOT REMOVE THE RED TERMINAL FIRST (like in this video)

Looks great!..but a lot of work...is it worth it?..bc i have 4..3 are damaged..I am ready to throw them.out n buy new😮