วีดีโอ

Is this still the best way to do it?

Great video. Tks so much. Is it possible to do this on the Creality K1 series?

Hi, I have an Ender 5 plus and wanted to upgrade it with the BTT E3 mini v.3 and the TFT35 v3 display, so this video looked like a godsend for me. Firstly, I attached the board to the printer then attached the display to the board. When I powered on, for a few seconds it reported no printer attached, then changed to Ender-3 ready. (I am not very experienced, as you will find). I assumed that this is the firmware the brand new BTT Mini E3 v.3 ships with. I followed the steps in your video to the letter, and created the firmware.bin file. I then copied it from the klipper/out directory onto an SD card formatted as directed. When I placed it in the card slot on the board, nothing changed that I could see. I continued to the steps for the display, and again copied the firmware file to an SD card and inserted it into the slot on the display. Again nothing appeared to change when I switched on the printer. The screen still shows Ender-3 ready. I have gone back to the beginning and repeated the whole process again with the same result. Am I missing something or can you help me get this sorted. Rather than go through a lengthy conversation on here, Are you on Messenger?

Great tutorial, but it seems like your whole hot end assembly moves when you touch it.

Thank you, bro! found what to do with my old canon 1100d!

Why would you even use OctoPrint? :'( It's so clunky and old.

would this work with a Ender 5 S1 psu?

Thanks, I’ll be following this mostly for my E5+

where did you put the hotend fan and the nozzle fan?

i just recived the btt kit ( pi v1.2 /tft35 2.1v / filament sensor / skr mini v3) there is file for the touch screen as i can see only for the 3v with the knob ? thanks in advance

i have the skr mini e3 v3 and i CANNOT get the display working... tft35-e3.... will not display anything. it flashes the file, but no emulated marlin mode... im dying here pleasse help

I have used some parts of your config but its throwing me an error "bltouch not deployed" when I try to home it (ender5plus, btt e3v3 mini, microswiss direct drive and pad 7 tablet for klipper). Do you have any ideas how ti fix it? It has a tendency to hit the bed sometimes but I think the bed is raised enough to be able to deploy correctly.

Nice video ! Got a question. Is it really necessary to change the firmware of the display? I kinda like the touchscreen part :)

Does this translate to using mriscoc as well??

This is explained so well and clearly. More people should take this as an example of how to give a good explanation of how something works. Thank you very much.

I am new to the 3D printing hobby but this is one of the best videos I have seen, thank you for sharing your experience, great video.

I know this video is two years old, but will this setup work on an E3 V3 as well?

nice tutorial ! i am currently working to convert my ender 3 v2 to Klipper and there lies the problem. is it okay to follow your steps when im using mainsail regarding to the pi stuff like in 23:32 if i have another username would pi still be okay or should the "pi" be replaced with something else like the user. im gonna convert it to mainsail not octopi-Klipper

Thanks for this! For me it is a great improvement over manually moving the hotend (or even worse disabling the steppers and pushing it around). I successfully used the "M0 pause" version on my new Ender 3 v2 Neo. The "M0 pause" version didn't behave as it should have. That's a bit of a puzzle, as I'm pretty certain that the Ender 3 v2 Neo has the 32bit board.

Hello, I am getting an error stating Error on 'M140 S': unable to parse I am running klipper on a direct drive ender 3 pro.

Hi, Thank you for sharing the Klipper installation in such detail video. I have a Ender5plus with SKR Mini E3 V2 and TFT35E3. I followed the video til the part requires to flash the motherboard of the printer with the "firmware.bin (renamed from Klipper.bin)". I turned on the printer while SD card has inserted, but the screen shows black only. There is no sign the new firmware has updated to motherboard. Then I also keep going to the part to paste "ls /dev/serial/by-id/*" , but putty returned as "ls: cannot access '/dev/serial/by-id/*': No such file or directory". On Octoprint, it shows Klipper standby. On the SD card, the file extension has turned "cursor". Any advice I should try. Thanks

I got a quiet duck with my SKR mini v3 (it won't quack when squeezed). Still quite though.

this didnt work on my v2. the z axis doesnt keep down, it just goes down and up again. useless

Can someone explain to me what keeps the accelerometer mount from melting on the heat block?

Thanks so much for sharing this. I really liked your pattern for leveling the bed. Made things a whole lot easier.

So do I need to add all the G29 codes or just one of them?

Great tutorial! I’m facing an issue where lithophane maker export zip doesn’t have an STL inside or the stl that is there doesn’t have the settings im putting into lithophane maker, anyone else experiencing this?

Are you using the BTT TFT v3.5 display?

Very helpful and informative, but this is the second video I've seen that doesn't take two seconds early in the video to explain what is a lithophane print. How does the image get onto the 3D printed sphere? It isn't clear until about 30 minutes into the video that the image is printed through varying the thickness of the wall of the 3D print. Don't you think that should be covered early in the video?

Trying the gradient trick and in my stl it’s not curving upward with the bulb like in your model. I’m getting a more hard edge making a bridge overhang then back to bulb surface. It’s like the website is now taking the darker portion of the gradient and flipping it also when ‘flip’ image is chosen.

I love you!

my recommended maximum accels do go over 3000... What can I do to get the printer more capable? Everything is tight and greased up

what aspect would u use for 1 photo

Great video. no brainer to subscribe.

Great tutorial Evan!

Can this be done with my Creality silent board on my ender 5 plus

interesting. I'm trying the first test. I'll try the second test sometime. Looks like a little more knowledge of your individual printer required. I'm still pretty new to this. :)

Thank you for describing all the settings.

Excellent tip with the gradient!

Nice work

Amazing video that explains all the key components simplified. Thank you so much, I tried to look on the GitHub page and couldnt find the info so I'm glad I came across your video!

sony A6000 doesnt do capture target command. Question is how do i modify that script to tell it to just download the snapshots to a directory on the device running klipper?

would this work with a Creality Sonic Pad?

Does this firmware work with the creality touch screen?

Love your videos, I got my first 3D printer a month ago (Ender 5+) used for cheap in Facebook. Played with it stock for one week because I found your video and now I’m all in Klipper, made the fan modifications and all; it’s been amazing. Thank you so much for all your videos. Any chance you can talk about your print head different print heads what to look for? Direct drive and all that? Have not found much information that’s concise online. Thank you and great work!

Why don't I have the "Autotilt current mesh" option under my leveling settings? Everything else seems to be the same as in the video. I'm using the 5x5 version though.

shit, too much hard work

Thank you for this facinating video. My printer is a Voxelab Aquila X3, an Ender clone, so no modifications were needed. I downoladed and ran the m0 code. It works for the first 2 positions, and then stops. Start has no effect at that point. What could be the issue? You mention setting Z offset with a piece of paper. Do you have a video on that process?

I got a problem with installing the screen thing and I went I done all steps but it just shows a glitched original screen can you help me

Love your guide. Still planning on getting klipper on my ender 3. But I'm curious, were you able to fix the z banding issue? I have a month-old ender 3 (although it's been mostly printing non-stop). Recently im experiencing a lot of z banding. Any inputs would be greatly appreciated.