วีดีโอ

Thanks. I was trying to get the sensor wire unclipped. It was WAYYYY easier to just unclip the sensor.

Thank You!

Thank you for this video. It's even better than the instructions on the paint gun ❤

This worked thanks

Why would anyone use the rectangular one? Esthetics I assume? Took me 3 doors to notice the round one.

My dish washer does NOT have anywhere to secure it by its sides!!!

I just bought a used 2018 from a dealer. Didn't notice this was loose when I test drove it. Saw it when I was halfway home. Thanks for the video! I ordered screws before I realized they were still laying inside.

Well done, sir. Thank you.

I have a quick question: what if I cannot find the crank anymore and I find another one with a shorter arm do you think I can use it?

Thank you! It worked! Doing a little happy dance because I fixed it and didn’t have to ask my husband for help 💪🤣.

Thanks for taking the time to produce a concise and succinct message

You from pittsburgh dude??? I heard that accent.

Thanks for the video, I have the same problem with a loose crew.

Thanks! I had no clue what to buy! I'm ordering now so I can fix mine!

Just had this happen to me and was able to fix it in about 15 minutes, thanks for the video.

hi - i did what you did and replaced it. however - there is some drip remaining whenever i push the push-pin divereter. there is some drip coming into my tub spout whenever i turn the shower on any assistance ?

Thank you for making and sharing this instruction. You're right this is a lot cheaper than replacing the wand.

Thanks - was exactly what I needed to fix my truck. TIP: the screws are awkward / tricky to get back in. I put a strong magnet on a screwdriver to help keep the screw on the tip until I could get it started.

Thank You !!!!

Thanks so much for this video. After my O Cedar broke I bought another kind for $100.00. It is a piece of junk, at least the 6 mop heads for new one does fit my old one.. I am so happy to be able to come to You Tube to learn almost everything. I am thrilled.

Thank you for your help ! ♥

What type of wires did you use?

Are the two inside lugs for line power and outside lugs for the load? or is the box different then my Square D

Thank you!! Made it easy to follow from start to finish!! Appreciate you!

This is just like my windows and thanks for the tutorial. Particularly the left & right advice was very helpful!!

Super helpful video. I don't suppose you have those directions laying around you could copy and email, do you? My door came sans the directions. And, the website is defunct now. So, a little outta luck here. Maybe post in your comment if you can't get directly to me? Thanks a ton.

I too am grateful, worked like a charm. Thank you!

Thank you so much I tried to do the dishes and this happened you saved my ass from a beating

Yum yum

Charbroil is so annoying with the damn stickers!!!!!! Why????

can you use channel locks for the step at 0.52 ?

Thank youuuu

thanks dude, you saved me a new dw!

Thanks for the video. I have the same sink that I hope to replace with a 33x22 porcelain drop in. Is it safe to assume it will fit? The ring on the old one measures 33x22. Hate to pull it out only to find the hole is too big.

You’re a legend and a hero sir!!!

Wow it really work!! Thanks for 5he help,you just save me lot of money

Nice job. Exactly what I'm looking to do. I'm a little nervous as I don't think every window was put in square (I did that opps.) I know the first window I put in was off by a little as I did it alone. Doesn't look bad and operates fine.

thanks for the tips

Thank you. Very helpful. The first video of someone keeping the old flange. This saved me a lot of money. I almost gave in and let roto router come out to cut my old cast iron flange. But thanks to this o can keep it and do the floor myself thanks again.

Great video Do you have a video showing how to add a disconnect switch with the breaker and motor?

You can remove the aerator all together and get much better water flow. I do this every time I buy a new fixture.

Thank you so much

Cheers, mate. Love how you don't waste any time, while still providing a good explanation.

Nice job. thank you!

You saved me big time. THANK YOU!

I'm having this issue right now! You sound like you know what you're talking about? I'm gonna try this as soon as Star Wars alcolyte goes off. Thanks in advance 😊

❤

Maybe the “tamper proof clip” is not so much to deter “tampering” as it maybe is to keep the tower from slipping from the setting you have it at? Idk, seems like that would make more sense than to discourage weirdos from messing with it, so they should rename it. 😂

You know I'm calling 'Crazy Uncle Bob' 😊

I just wanna say huge thank you to your video!! I've had a screw rolling around somewhere and couldn't find it.... until now!! It was driving me crazy! Thank you again!!