วีดีโอ

My Commander XR Magnum is degassed but I cannot remove bottlw. Too tight. Suggestions?

would it be possible to do a similar video for the sniper xr

👏🗽

This is a MUST WATCH video for anyone having/receiving a Brocock/Brk XR

As I've said b4, I love your work. It's easy to understand you and you don't go too fast. I recently got my Atomic XR and when I removed chasis to lighten the trigger, there was no warrning about "watch out that the spring and pin for power adjuster don't fall out". Gues what, they fell out and I lost the spring. I friend lent me his while AOA sends me another and your video, THIS video, saved me because I had no idea as to if the sping went on top of the pin or below and what side of the pin faces "down". THANK YOU. Do you have a video on trigger adjustment on Atomic? I also want to see a video on Hammer Adjustment. This is my first Brocock/Brk aside frokm a Pathfinder XR that arrived from AOA leaking and I sent it back and got this Atomic XR in .22. I'm in Connecticut USA

Did I miss 1:36 the bit requiring a .89mm allen key

I bought the ghost plus 177 and love it , it seems to like HnN. BARRACUDA 8s best and I’ve tried quite a few so now lives on these , great vid 👍

Hi could you tell me what the thread is on the muzzle, also could you just screw a moderator on the thread with no shroud, would there be any loss of accuracy thanks 👍

Hi this is the same for the Brocock commander XR.22 ?

Where are the slug barrel?!

Brilliant, thanks for making the instructional video

Can you replace the muzzle break with a moderator?

Hi. Can the bottle be degassed by unscrewing the pressure gauge instead of the reg? Thanks

Hello noobie question if rifle comes with a spare air cyclinder Whats its use can you fill the spare air cylinder and then when current empties you change bottles? Is it even possibble to remove the tank with some pressure left in it?

This is one of the finest disassembly videos I’ve ever seen. The commentary is super clear and easy to understand. I also appreciate how leaks from failed o-rings are clarified. WELL DONE!!! Thanks for putting this together!

Not only excellent in content but after the stress of a leak or failure the presentation is like therapy... EXCELLENT VIDEO...

I love my pathfinder its very accurate and so light

The later models also have a little grub screw , where you put the flat head screw driver to adjust reg pressure

P r o m o s m

How much is this

Great video

👍👍👍

Excellent video as expected thanks very much 👍🏻 Just a few thoughts, what is the best bottle pressure (or what bottle pressure would you use) to set the reg pressure. I notice on my Ghost when the bottle is full (250 bar) the regulator pressure gauge reads 5 bar higher than when the bottle pressure is lower-say 160 bar? Perhaps my reg is ready for a service but doesn’t creep (or at least no higher than 100) and has a respectable refresh rate so I’m happy with it. Only makes about 10 fps difference on pellet velocity from 95 to 100 bar reg pressure.

The airgunners champion

The airgunners champion

Another great video Jeffsky

Great info, thanks

The airgunners champion.

Exellent video! Thank you for sharing

Se puede hacer cambio de calibre?

Dam now im gunna spend more money

Nice to have all the accessory's in one easy to find place 😁 some nice bits in there

Nice one 😁

what size is the plenum please in cc? thank you Sir

Can you do a compatto?

Hello, is it possible for you to answer my question regarding the FAC valve? It would be much appreciate.

Awsome 👌🏻

Very nicely machined gun. Looks like it should last a long time and give good service. Thanks

Hello, is the FAC valve a 'Balanced' type with a tiny hole venting from the back of the stem and into atmosphere? Or is it just that the the HPA side of the valve has a reduced area lessening the plenum pressure on the valve itself?

Dear BRK, amazing rifle...I already own the Ghost with the HP 177 and 22 barrels and all 5 of the hammer springs (pre color coded editions). Will the .22 tensioned barrel that Fady used be available on its own? Also can you comment on the set up Fady had for the .22. What was the Regulator set pressure, what hammer spring, Power Wheel setting and what pellet? Thanks

Very nice version! Is it possible to get the cocking lever for my ghost?

Daystate taking over Brocock and changing the name to BRK was a smart business move. Even my buddies with the typical 10 year old mind get a chuckle when the name Brocock is brought up and honestly childish or not the name should have been changed long ago. I believe the quality will go up as will sales and reliability under this new management. The Ghost is a hit that's for sure.

Great little gun! How many fps on sub12?

Have a Ghost Carbine but would like one of these.

Excellent Jeff, thank you! Regulator questions: The sealing disc, no requirements that the cut out is aligned in any specific way? Did. you use silicone grease to lubricant the belleville spring discs? Is there a maximum set pressure not to go above on the Ghost's regulator? again greatly appreciate your videos and expertise!

Great video as always mate.

Ka cara pesen barangnya gimana

A very straight forward job with the aid of this video. Thanks for this ....

Thank you, excellent video as always...esp since my .22 barrel kit should be arriving today. The Ghost has 5 possible hammer spring options, and I now have all 5 to go along with my .177 HP. When the rifle was designed, what is the expected use of the various hammer springs? Ie Diabolo pellets have an "optimal" velocity of ~850 ft/s, so which hammer spring, with what regulator set pressure, with what barrel length...knowing the pellet caliber and weight? Will put the rifle in the approximate "optimal tuning", at which point I would expect the Power Wheel to be used to optimize. Is there a sweet spot range of regulator set pressures?

🏃