- 71
- 1 833 135
KJ
Hong Kong
เข้าร่วมเมื่อ 10 ส.ค. 2014
Cordless Impact Wrench Restoration DeWALT DCF 880
DeWALT DCF 880 brushed lithium battery wrench
The exterior is worn and dirty, and the interior is severely worn.
Clean and polish the shell and re-engraved the label. The interior was completely disassembled and cleaned, and new bearings were replaced.
After the repair, the power is strong and the wheel hub screws can be removed without any stress.
The exterior is worn and dirty, and the interior is severely worn.
Clean and polish the shell and re-engraved the label. The interior was completely disassembled and cleaned, and new bearings were replaced.
After the repair, the power is strong and the wheel hub screws can be removed without any stress.
มุมมอง: 65 447
วีดีโอ
Rusty flat vise- Perfect Restoration
มุมมอง 6K21 วันที่ผ่านมา
The small flat-nose pliers were severely rusted. They were sandblasted to remove the rust, polished with putty, and repainted with military green paint. The screw rod was re-nickel plated and fully functional after reassembly.
Cordless Circular Saw Restoration Makita 4190D, replacement of 21700 battery cells
มุมมอง 99Kหลายเดือนก่อน
The interior of the Makita 4190D Kitty Hawk saw was severely corroded by water, and the motor was stuck by rust. The metal parts are sandblasted to remove rust, repainted or blackened with blackening liquid to prevent rust. Fixed broken shell The battery was partially disassembled and replaced with three strings of 21700 cells. Eventually full functionality was restored. The metal parts of earl...
Impact Wrench Restoration DCA ADPB280
มุมมอง 44Kหลายเดือนก่อน
The DCA ADPB280 was nearly new and was run over by a car, causing a comminuted fracture. The battery cells were exposed, four cells were missing, and the wrench casing was damaged. Repair the plastic shell and reinforce it with magnetic nails and copper wire. The internal gearbox is almost brand new, and the grease has not changed color yet. It was simply wiped and re-greased. The battery part ...
Revive Fluke 15B Multimeter | Switch to lithium battery power supply
มุมมอง 18K2 หลายเดือนก่อน
A Fluke 15B multimeter that came from picking up trash. Over the years, the outer shell became very brittle and chipped away while polishing, so the front outer shell could only be replaced. The red wire was connected to the negative pole of the power supply of the previous motherboard. The test machine broke down and smoked directly. Fortunately, the main parts were not burned out. I replaced ...
Cordless Impact Wrench Restoration BOSCH GDS 18V-EC 300 ABR
มุมมอง 646K2 หลายเดือนก่อน
Bosch GDS EC300 brushless motor Cordless Impact Wrench, nominal torque 300 Nm. The motor makes a sound but does not turn. When the machine was disassembled, traces of water intrusion were found, the interior was severely corroded, the aluminum shell was deeply corroded, and the motor stator and rotor bearings were rusted to death. The internal condition of the gearbox is good, the circuit part ...
Restoration of Impact Wrenches Milwaukee M12 2454
มุมมอง 20K3 หลายเดือนก่อน
Milwaukee M12 2454 12V Impact Wrenches. The appearance of the rubber coating is damaged, the shaft sleeve is broken, and the main control cannot shift gears. The shell is re-wrapped in double-layer lambskin, the brass bushing is customized, and the main control is re-wired. After repair, the power is strong, and the 130NM wheel hub screw can be easily unscrewed.
Cordless Impact Wrench Restoration BOSCH GDS 18-Li
มุมมอง 171K3 หลายเดือนก่อน
The shell of the $5 Bosch GDS 18-Li electric wrench was completely broken, the main control wire was disconnected, and the inside and outside were covered in sludge. Fortunately, the gearbox is in good condition, the main control is good, and although it lacks carbon brushes, the motor is in good condition. This time, the casing was repaired, labels were made, the gearbox was completely disasse...
Reciprocating Saw Restoration | Makita DJR185
มุมมอง 12K4 หลายเดือนก่อน
Makita DJR185 Reciprocating Saw looks acceptable, but opening the casing exposes various problems. The motor is stuck, the main control switch is drilled, the inside of the chuck screw is broken, the front and rear shells are assembled, the tool holder is broken, and the switch bezel is broken. . . Fortunately, the problems have been solved one by one. Reassembled an 18V battery with brand new ...
Cordless Drill Restoration | Dewalt DCD777 18V Brushless Drill Battery Rebuild
มุมมอง 166K4 หลายเดือนก่อน
The Dewalt 777 brushless electric drill, which is terrible to watch, works well in a test run. The outer shell is covered with a thick layer of hard glue, the gearbox lubricating oil has dried up, the gap is large, and the chuck is worn through. This time, the most time was spent cleaning the remaining glue on the casing, completely disassembling the gearbox, relubricating, replacing the new ch...
Impact Driver Restoration Bosch GDR12-Li refurbishment and repair
มุมมอง 113K5 หลายเดือนก่อน
The Bosch GDR12-Li screwdriver is commonly known as the little fat guy. It looks terrible. After disassembling it, it was found that only the motor was stuck. After cleaning, the motor rotates freely and the sound is very nice. Most of the time was spent on repairing the casing. The rubber covering fell off. I chose chrome-tanned cowhide, cut it and pasted it on. The label paper was redesigned ...
Burnt Dremel Multi-Tool Repair&Refurbishment,Epoxy resin glue reconstructed shell
มุมมอง 4.1K5 หลายเดือนก่อน
Dremel Tool, 12V Multi-Tool The machine was burned by fire. Fortunately, only the outer shell was damaged. After inspection, it was found that the inside was intact. The casing was cleaned, the missing parts were repaired with epoxy glue, and the bearings were replaced. I bought a machine head and it was fully functional.
Milwaukee 2754 electric wrench Restoration and renovation
มุมมอง 10K6 หลายเดือนก่อน
Broken leg version of Milwaukee 2754 wrench, Shell cleaning and repair, The broken part of the shell is hot-melted with steel mesh inside and fixed with copper nails on the outside. After repair, the function remains intact. Easily remove 130 Nm car wheel hub screws.
WORX WU531 Lithium Electric Circular Saw Repair.Repair motor
มุมมอง 4.3K6 หลายเดือนก่อน
WORX WU531.9 18V lithium electric circular saw, The coil of the 775 motor was ablated. After disassembly, the rotor was re-wound with copper wire and the dynamic balance was adjusted. After repair, the function is intact as before and the power is strong.
Repair Hitachi Electric Screwdriver DB 3DL2 Recovery Function
มุมมอง 6K7 หลายเดือนก่อน
Hitachi 3.6V folding screwdriver The switch has poor contact and the hand guard glue has fallen off. It was completely disassembled and the interior was relatively new and clean. I simply cleaned it and used lambskin instead of hand gel. The switch can be restored to function after disassembly and cleaning. Reprint and paste worn label paper.
Disassembly of einhell sandpaper machine and repair of lithium battery
มุมมอง 3.3K7 หลายเดือนก่อน
Disassembly of einhell sandpaper machine and repair of lithium battery
Refurbished Panasonic Electric Screwdriver EZ6225 Lithium Battery Replacement
มุมมอง 6K8 หลายเดือนก่อน
Refurbished Panasonic Electric Screwdriver EZ6225 Lithium Battery Replacement
Revive the Makita 454 electric drill, rewind the motor and repair multiple faults
มุมมอง 34K8 หลายเดือนก่อน
Revive the Makita 454 electric drill, rewind the motor and repair multiple faults
Restoration and Refurbishment of a Badly Broken Milwaukee M18 FID
มุมมอง 24K9 หลายเดือนก่อน
Restoration and Refurbishment of a Badly Broken Milwaukee M18 FID
Panasonic EZ6810 electric hammer dismantled and refurbished to assemble 24V lithium battery
มุมมอง 6K10 หลายเดือนก่อน
Panasonic EZ6810 electric hammer dismantled and refurbished to assemble 24V lithium battery
WORX 12V Multi tool Dismantling and repairing
มุมมอง 2.1Kปีที่แล้ว
WORX 12V Multi tool Dismantling and repairing
Bosch PSB 14.4V Electric Drill Restoration and Refurbishment
มุมมอง 3.1Kปีที่แล้ว
Bosch PSB 14.4V Electric Drill Restoration and Refurbishment
Bosch GBH 180-Li Cordless Rotary Hammer Drill Repair Maintenance Refurbishment
มุมมอง 26Kปีที่แล้ว
Bosch GBH 180-Li Cordless Rotary Hammer Drill Repair Maintenance Refurbishment
Reuse of old batteries DIY assembled fill light
มุมมอง 1.5Kปีที่แล้ว
Reuse of old batteries DIY assembled fill light
Repair and refurbishment of Panasonic remote control electric screwdriver
มุมมอง 5Kปีที่แล้ว
Repair and refurbishment of Panasonic remote control electric screwdriver
Dismantling and maintenance of Hitachi 10.8V electric screwdriver
มุมมอง 1.6Kปีที่แล้ว
Dismantling and maintenance of Hitachi 10.8V electric screwdriver
Makita TD131D electric screwdriver repair and refurbishment
มุมมอง 4.3Kปีที่แล้ว
Makita TD131D electric screwdriver repair and refurbishment
RYOBI 12V Lithium electric grinding repair
มุมมอง 2.2Kปีที่แล้ว
RYOBI 12V Lithium electric grinding repair
Refurbished and repaired vintage electric fans
มุมมอง 624ปีที่แล้ว
Refurbished and repaired vintage electric fans
Зачем было так издеваться над своим бошем, чтоб потом его реставрировать? А ведь полюбому он твой
原来是垃圾佬,熟悉的VS😂
😀🤝🏻
👍👍👍👍👍👍👍👍👍
Top de mais!!!
Wow,was really enjoying this vid till the puddy was put on.
It’s crazy how restoration became a bath of shit and then cleaning+teardown
❤ احسنت
i just changed the motor for mine( it cost just 12eur) and made a 16v 6Ah Li Ion battery for it :)
Te equivocaste en el sticker. El original dice "Professional" el que tú hiciste dice "Professinal" 😂😅😅😅😅😅 te falto la letra (o)
Thank you for pointing out my mistakes. English is not my native language and I often make mistakes. I will check carefully next time.😀😀🤝🏻🤝🏻🤝🏻
Repairing BOSCH with Makita - LOL
Muito bom
You need to treat your table vise also.
Nice
The video belongs to a DeWALT service worker
This wasn't a restoration it was a deep cleaning lol
What’s he gotta do for you to think it’s restoration then? Melt the materials and recast them? Seriously man, he even printed new stickers for it hahahaha
Бл как так то 😢
excellent restoration job
Bro give giveaway i am watching in Tamil Nadu bro i like your channel
🤝🏻🫰🏻
Will that crystal protection coating hold up against petroleum products or will it get sticky/ come off?
It is a relatively hard shell that can protect the left and right🤝🏻🤝🏻
Не доконца почистил его и не закрасил, ремонт чисто на отьебись
😮 ai montat greșit discul de taiere
I checked carefully and finally I installed it correctly. It was wrong on the previous machine. There is an arrow on the shell to mark the direction. Thank you for your reminder, welcome to follow me🤝🏻🤝🏻🤝🏻
La mejor restauración que he visto ❤uf exelente trabajo Dios te bendiga saludos desde Colombia
Thank you for your continued attention🤝🏻🤝🏻🤝🏻🫰🏻😀
Complimenti! Sei un grande operatore!👍🤝🏅😊
Thank you for liking😀🤝🏻
Restaurado chave de impacto sem fio 🚫🔌😉
good bro 👍👍
🤝🏻🤝🏻🤝🏻😀
Beter that new🎉🎉
So beautiful a restoration indeed! ❤❤❤❤❤❤
Very very good bro❤❤❤❤
Sensacional
wtf
Num gastou nada só spray
17:53 next this big old bench vice
😄😄
Pretty grimy.
Very splendid restoration job. The impact wrench looks much better and it works like a charm too. Excellent work.
Very nice refurbishing project. I especially like how you reworked the decals. Clever I'd say. I actually had a local business give me their broken 1/2" impact DeWalt cordless driver because the anvil nose section was broken. So I bought a new DeWalt replacement nose anvil and cleaned everything up and have like new tool now as well. Those 1/2" DeWalt impact drivers are seriously powerful for sure... Thumbs Up!
Thank you, you did a great job too.👍🏻👍🏻👍🏻
Excellent, very good recovery
Excellent job
👍🇷🇺👏🇷🇺👍
10/10 ❤
Очень здорово ! Спасибо , что дал вторую жизнь этому бедолаге . Теперь он попал в хорошие руки . 👋
Thanks, now it's like new and has great power😁😁🤝🏻🤝🏻
он и так не умирал. просто работа грязная (это не точно)
What is the water do you use in ultrasonic machine?, and what’s the spray do you use after that. Love you video❤
😢 no sandblasting? So it loses interest for me.
The motor is no good.. replace with standard 540 motor
哥们技术很棒
Please explain which solution you use.
Жігіт,тамаша
“BRUSHIESS” 😂
🤣
Top
and you cost hours to fix that....that handle which only worth 3 USD.
what the... you assamble a battery pack like that? no cell holder? no screws to secure pcb board??