วีดีโอ

In the winter, i have to saw at a snails pace or i am getting waves

👍👍👍

Hi, I am running a small sawmilll operation in India and I have installed woodmizer lt70 wide .I wanted to know how much cubic feet of wood or board feet can we cut in a 8 hr shift .

so your net didnt go down? they running a cable system in my hood 2 big as wires on poles i am like you the winter in the south will bring the lines down off the old power poles

old truck mud flaps please work carbide on rubber

rubber workon a mat carbride will chip

I don’t know if you guys know this, but save the damaged carbide. It is expensive scrap. Since you use a lot inserts on your cutters it may take several years to get enough to get some money. The last I checked it’s $6 a pound

I think you just nailed why my electric hand planer is leaving waves.

So do the cutters on the right or left side of the head wear more than the other side just due to the normal path of the lumber through the planer? By the looks of the breakage, you really only have one turn, 180 degrees as the 90 and 270 faces have bits missing as well.

I use fingernail polish to paint the old insert edges before I begin so I can then easily keep track of where I am for changing spiral cutter inserts. Further I always know how many more changes I have left. This is very handy when I get interrupted during a cutter change and later when I return can restart changeover easily. Ray

Get the 6" face on top and bottom first. Then, saw the other two faces turning the log 180 after every cut until you get down to 5 5/8". Now, cut the square cant turning after every cut to take out the stress. Lumber will be much straighter.

I have a 18 inch Woodmaster planer with spiral head cutter. It takes me half a day to change them out. So i know what you are talking about .

Outstanding Do you sell firewood as well ?

Stay safe out there!

Thanks for taking the time to share your knowledge. Have you ever done a video segment on how you strap your lumber stacks? You refer to how hard Matthew worked to strap this oak in an effort to minimize warping. Would love to know about the tools and strapping you use. Been following you for awhile and maybe I missed it. Thanks from Maine!

The birds sure are happy at your place .

Now glue it all back together again and you got yourself a glue lam beam with half again more strength.😊

Is there any advantage to keeping the cut pieces in place while you cut below? I would think the extra weight would cause an issue on the blade.

So why is lumber expensive ?

It's a coming

Great video, as always. I haven't been able to comment lately cause I've been in youtube jail, but I just wanted to say hi and glad you guys keep putting videos out. Keep warm. It's 9* as I'm writing this.

the banding kit i was in the metal banding world i have the metal reel and tools for industrial work they were stupid expensive in the 2000 s teach me the strap and were to buy please make a good vid in the heat be a good filler. the racket for metal band is over 400.00 but thats what we had to use . .one company want one clamp the airplane wanted 3 clamps if you every cut steel bands before you know whats up. thing of the past

Have a question. Does the waste cut materials go for firewood such as slabs. As always, thanks for sharing your thoughts and advice.

I still have no idea how to sticker or stack 😅

This job seems made for end drying with a Vacuum kiln as lumber could be cut into full width slabs seven quarter thick then dried and then cut into 5+5/8 wide boards and surfaced planed to 1+5/8 thickness extra work but you get plain sawed S4 laser straight dried flat white oak boards that will not move unless you add water with almost no waste. Do you have a spare vacuum kiln laying around? Ray

Nice load of oak logs Eric

I drool when I see >25 and >50 stuff tossed on the pile. For toy making that would be great.

Funny, im cutting white oak this week as well and ive had the same crooked movement on boards. I swear white oak is difficult and everyone wants it. I get tired of it.

Great video guys, very nice job !👍🏻

That's great. No way my mill would let me cut that fast.

Great job.

Thanks for the lesson. I’ve never torn into a cylinder, but I need to. I had to replace the clamp cylinder on my Wood-mizer and backordered a seal kit for the old one. One of these days, I’ll swap out those seals so it will be ready to go when it is needed.

i am at 1240 do you have the tool to put the inside glade in the pistion that is a super bitch if you dont wanting to see.

go borrow your friends 3/4 impart if that don't work 10 ft pipe the rod nut are stupid tight 400 ft lbs plus . why i have used a crane to brake the nut lose and broke a lot of tools . even borrowed a 1inch impact gun broke the anvil off had to buy the man a new gun. why that nut has to be that tight ugh.

Always wanted one of those

mat is busy i guess .

if you know all the seals in a cylinder McMaster Carr is the go-to. motion industrial wants you to ship the cylinder off they rebuild it at a stupid price

I wish i had gotten the bigger motor. Sometime i have to run too slow on oak in order to not stall and the cut shows. Oh well live and learn.

surplus center and broken tractor they have great parts diagrams we use them on every tractor, fyi surplus center has cylinders cheaper than some kits just have to write it down if its your machine

Thanks for the how to video. Deere isnt what they used to be.

Nice job and an in-depth description of your repair , thanks for sharing . Living in the real world in Macon county NC .

Having replaced many seals in my time, I must say that your descriptions was one of the simplest and clearest explanations I've heard!! Very good video!

JD unique gland. PATENT issues.

I have replaced the seals in the lift arms on the Case 1845 skit steer We have the spanner tool to unscrew the nut. we have had had to pull the rod out with the other skid steer

Morning guys, I guess those old heavy logs are tough on the seals on the cylinders..

What do people use that dimension of lumber for?

On my manual Cooks MP32, its around 7-10lb push.

Gitten er dun

That's too nice to make two by four out of

Thanks! Good advice!