วีดีโอ

Your wrong came out in 2023 not 2024

I never liked vests, because my arms get cold too.

I did cause I was home schooled......lmao

From 2:24 - 3:03 in the video, notice the snow spraying out the (operator’s) left side. My Cub Cadet 3X30HD has the same flaw, which reduces the effective width from 30 inches to 24 or even less. This is one of many manifestations of the poor engineering built into this pathetic snowblower.

“Make my day”

Thanks for the follow-up review. I have the same stainless 92. Haven't had a chance to shoot it yet. Will probably do the spring kit and smoothing mods first. Read all the stories about it before buying. Paid about $250 less than you did. So you have a firearm that appears to be particular about ammo loading but loads, ejects and groups other ammo well. Yet the rifle is labeled a piece of crap?

This is the biggest piece of S#@T shotgun I've ever owned I'm so sick of this piece of crap I just want it out of my house it disgust me stupid MF!!

This is the biggest piece of S#@T shotgun I've ever owned I'm so sick of this piece of crap I just want it out of my house it disgust me stupid MF!!

Eco mode is what i use ours for

Great excuse to buy a firearm... ima tell my wife this 😂

I race a vw mk4 gti with a 1.8t motor im on 23 psi of boost. My car was pulling timing. Till i mixed 1 gallon of e85 with 6 gallons of gas. Now she pulls hard. Before i mixed e85 with 91 i used to mix 20 oz of acetone from homedepot and 2 oz diesel fuel. And that solved the timing issue also but its cheaper to mix e85.

It's a shooter for sure what grain it. U shooting

Lot more options for the 350 vs the 360 lots of companies putting out 350 legends just 2 I think on the 360

pure content.

It just might be me but those groups are not sub moa unless they were shot at 200+ yards.14:38 You might want to run a box test to check the tracking. What reticle does this have? Is it moa or mil?

Welcome back!!!

Rossi 92 in 357 mag does same to 38 special in older lever action guns.having cycling issues fur ammo.

excited about this release

This came up on my feed and I said “hey I know that guy”.. good stuff!

Nice groups…

We had over 200 centimetres last February over 3 days. 😊

Just got your email. That is correct so I dumped the other comments. And I do like the video, nice job.

Thank you sir.

Henry guns are great. My daughter n law's brother works at Henry. I got a beautiful 308 lever action at cost from him a couple of years ago.. They give each employee a chance to buy 3 guns a year at cost. Great company for sure. KA2AS

Hey from the South Carolina Coast. Where did you get the new cover from ? I bought new a 2007 Z51 3LT Atomic Orange Metallic 7k miles, always garage kept, but for some reason my air bag cover is so sticky and I can't stand int any longer ! 😂 Checked out your channel and I assume you like my screen name. 😂 I just subbed. Cars, boats and guns, love it !

Wait you put a 5 amp fuse in 10 amp spot? What ?

I was considering this gun until I saw this. THANK YOU

Excellent review. Thank you very much.

Great video! For our 40’ Chris Craft, they recommend 5-7x but that’s on Lake Michigan. On our Yamaha jet boat on the reservoir, we have an anchor but always use our 2 augers for the past 5 year with no issues.

Great job!

Yea definitely don’t need 7-10 for the boating we do. Best advice for the fluke anchor is a good mount of rode. I think I use about 6feet of chain on my 100foot line. Keeps the shaft of the anchor down and sets easily almost every time.

I never had issue with mybrossi lever action in 45 long colt; the side gate was stiff i admit that on loading; but gunsmith tolde takes couple hundred rounds for that to ease up.

What an idiot. Guy sounds super smart.... lol idiot

The slide isn’t aluminum, it’s stainless steel, just the frame is aluminum.

I have the 454 as well and i even sent it back for warranty work, still useless. i think ill buy the spring kit and hope for the best.

Guy completely ignores sign nearby….

You get what you pay for and now even the cheap stuff hurts the wallet

Dude, the slide is not aluminum.

Just use a hand steamer and forget all this chemical nonsense.

lol 10 total. its 9+1 but seems the comments already informed you. granted some had their glasses jammed in to their bridge when they pounded on the keyboard to tell you. but still.

if you bought it new or lightly used. work the action a lot.. like a lot. then take it apart and clean it. that should loosen up the action a bit.

Great video, thank you.

Love the Intro!!

I'm a 110 pound woman and it doesn't scare me Nancy

This guy must be trolling for Henry

Was there no anti-vibration damper on the lower caliper bolt? My 2013 MKX has them. On another note, putting the pads back on can definitely be challenging, especially the inside ones.

Great video!

Any chance the ribbon delete spacers match common pvc pipe diameter? If so what? 2 or 2.5”? Seems a little pricy. I’m sure someone has tried this hack out…

Sick!!!