วีดีโอ

Where I can get those seat or you recommend something better?

When a man is determined, a man makes a way! Mad respect brotha nothing better than being self sufficient!

What seats are those? Awesome!

thank you for the video. now if it happened to me ill do it at home

not a lie just did front drivers side with 2 wobble extentions no problem from the top need to thread through existing parts

Great job. Those lifts are crazy expensive ! I'm thinking about installing a jk frame under my tj. I have a j8/dana44 and ford 9. Those vevor pipe stands are pretty cheap and those could probably work too.

Great job, now put it back… in your sandals!

Just used this video to show my marines you can find anything on TH-cam

nice vid

You're a stud in my books. My wife has the same EXACT car (White 2020 X5 M50i with 70K miles) and we just found out that the front diff has the same issue. Fortunately, I bought the extended warranty so they are covering it....but I'm with you...they should have absolutely covered this under MFR warranty whether you had purchased the extended warranty or not. This is a crazy operation to do yourself...congrats.

This is on me, Had to stop the video due to the on and off music. The music hard to listen, yes I have mute however I don't want to miss your narration. I would prefer whatever shop noise is going on at the time. Good luck with the project, I moving on to something else.

Hey like all your videos, man….i have a 1165 i’ve been working on and going back to your videos and see how you did things… so on the old harness if you don’t take out some of the connections that you don’t need will it causing any problems I see that you took yours out just wanna ask if you didn’t take those out. Would it cause any problems??? Thanks

Hey bud. The 4L80 that comes in the Hmmwv like mine…. are they any good for the Duramax or no? Thanks

How did the front diff go out?

what do you do for living?

Thanks man for sharing you are right zero info and the dealer refused to help and this should be on the Grantee Mine M50I X7 and I had only 63000 KM

THE FIRST THING IS GET PERMISSION FROM THE WIFE!!!

Driver side front is no problem with a 16" extension on a impact with a wobble socket and two men.

Looks FANTASTIC! I never even considered a lift for mine because of the complications. Now it's a MUST-HAVE! Thank you for your great content.

Great video! 😎

I see that at 1:20 your girl is removing the shifter assy by removing those 4 bolts. I tried to remove those bolts to install some "L" brackets to then put a Master padlock through the "L" brackets to prevent petty joy riders to take off but the problem was that the bolt (the first one I tried) felt tight at the beginning but now just keeps on turning like if there was a nylon lock nut on the other side. Am I missing something...? (I did not mess with the other 3 bolts before finding out what I am doing 🙂)

Sure like seeing boys and toys. We need more Splitbuild videos....we're having withdrawals....

Sweet wheels, mind sharing the specs?

Great to see you back!!!

Damn buddy, been waiting for this one for a minute! Lol Glade your doing good man

I was just thinking about you the other day. Hope all is well.

Right on, good to see you even for a quick few minutes. Hope we get a new video soon. Take care and enjoy the summer.

A father, a son, their pup and their toys... Enjoy guys!

Lot work bmw x5 is good but crazy when oil leaks

New to your channel love the work you do. One question. What's going on with your audio in alot of your video's. It cuts on and off alot.

What’s the cable lock for on passenger seat area for?

Your my hero

Ypur my hero

how many miles can you normally go in between oil changes (I guess you do not use synthetic?)

At 3:25...it may have been his power steering resivoir spring falling out...if itsike an ECV.

GO SLANT BACK IT LOOKS BETTER

CDR valve serice pro tip. So you dont drop that bottom clamp after you loosen it. Place a small zip tie under it so it doesn't slide down once it's loose.

Pro tip for the fuel filter replacement. Lossen the 3 7/16 cap bolts but do not remove them. Do not disconnect any of the fuel lines. Instead, leave everyting on including the clamp bolt. From inside the vehicle while sitting in the drivers seat, remove the 2 7/16 bolts that hold the fuel filter bracket. Fuel filter with housing is now easier to move around to remove the 3 cap bolts to service the filters (green screen and molded paper filter). Clear the drain line. Clean the inside and fill halfway up with fuel and install new filters then the cap with a new o-ring. Place the oring in a zip loc bag and put it in the freezer overnight to shrink it. To prime, loosen the stainless steel screw at the top. Crank until only fuel comes out (no bubbles). Start and run the engine. Check for leaks then install into firewall by using an awl to center one of the bolt holes and install a bolt into the other. Tighten both once started. You're done.

black with pleany of crome and red sets

Get M1165 and then upgrade everything

Did you use some lift kit on this Humvee or not ?

Im glad you guys figured it out! Where do you buy all of the grade 8 bolts for the frame and suspesion? Is there a list of all that is needed?

Whatever you this can't be made luxury

😛😛😛😛😛😛❤❤❤❤❤👍👍👍👍👍👍👍

Remove center bump if you want to make is luxury and usable.

Doing the same thing and can’t find the plastic axle cover. Where do you find it?

What is the maximum temperature indicated by the coolant needle that you have ever reached under effort? Have you ever touched the line/notch next to the middle when overexerting yourself? Thank you

Marshall!!! . More HUMVEE content please 😊. Or Anything. Hell, make a ham samich and do some sweet ass cartwheels or something. We miss you Brother!!

Is the fiberglass hood so heavy to be carried by 3 people?

Nice video bro, lucky I watched your video. I’m going to need something to support the engine wow. Thanks! I got a 2015 but it looks the same.😊