วีดีโอ

I use it every morning. Still going good. no real complaints.

They ship the boxes over a few days. Rest a sure you'll get it.

Sorry friend. I don't do any other social sites. Best thing is to look at the exploded schematic. You have to take of some pulleys to get the cables through. Good luck

Best to research things carefully and build it out slowly. Thanks for watching

One other is it does not keep track of individual drink counts. Only coffee and milk drinks for a general count. Total cleanings and carafe cleaning are counted

They are 3d printed from thingyverse. Somewhere in the comments I left a link for the poles and the clear covers. Somewhere in the comments in 1 of the 3 or 4 videos of the track. Still working on it here and there. It is a life long thing. Just got a new large tapestry to wrap around the track perimeter . The track is 6 years old. thanks for checking it out. I should put a video up.

Thank you buddy

Thanks. Oh yeah... it sits behind my desk in my house office so I race 2-3 times a week. It is a long term project that is been setup since 2018.

th-cam.com/users/shortsKt6pvdxD4hM

Windsor the Jack Russell Terror can barley contain herself whenever I run the cars.

@@tubeaudioslave When we had cats, there were times where I would set up a track, could not get a single lap in while the cars got attacked, then took the track down. I'm telling you, the pet stores need to sell these, Lol! Have fun with the cars and your pet!

No. there are no jumpers at all. No more than 4 cars at a time or it will require it. Keeping the track clean is important for conductivity.

If you add the chips to the lane changer tracks to prevent cars from changing lanes into each other it will disrupt the continuous power and yes power jumpers would have to be installed where the switches are otherwise they are not needed unless the track gets really long. Hope it helps.

I still work on it here and there. good luck in you build. They need to come out with some Carrera Digital F1 cars to re inspire me.

What's F1 cars?

Formula 1 racing cars. They had them years ago and scalextric makes them but they need a digital chip conversion and they are very fragile to race with all the wings and the mirrors brake off

Dusty desert environment

@@tubeaudioslave thanks for replying 🙏

I used the included wall brackets. They are tricky. Worst case scenario just use the top ones. Its so light it doesn't really need the lower mounts. Just prop the bottom out with a 1x4 or something similar to get the angle you want.

It has been a great screen. I keep it covered when not in use. For the money the aluminum frame is pretty amazing, and the black velvet makes it better for viewing.

Thingyverse. 3d printed. Here you are. Would need to be scaled probably. www.thingiverse.com/thing:2220722

I know it is not a great video but appreciate the positivity.

@@tubeaudioslave But it is. Giving concise information in a relatable way need not be 4K or mic with a mixing board. Cheers 🍻

Correct. It's the most realistic one for the money

I miss it sometimes. I used it when I had a sailboat for grocery runs and Bar hopping. I think I paid 2200 bucks for it. Sold it for about that. I think they used to rent them on lake vacation areas in the 90's

Yeah I need to make some more racing vieos of the track. Thanks!

why no actual footage of the screen lol?

i didn't think of it I guess. I still use it. Its worth a buy for the money. The aluminum frame is nice with the fake velvet. @@alandalehoward3

I linked some of the parts including the lights in video #1 showing all the 3D printed parts th-cam.com/video/eiFQNFKPKk8/w-d-xo.html

In the comments on video one. You'll find the lights there. May need to be resized for you needs.

I put one up racing the cars for a few minutes

th-cam.com/video/uKEZzGFrdXU/w-d-xo.html

I could not locate them. Here is the planner I used though. You can download it there if you scroll down. thanks

www.slottrackpro.com/carrera-track-planner/

@@tubeaudioslave ok. Thanks heaps...

No heating problems. Does not tax the motor ar all. There is no servo. The throttle is Magura. About 65.00.

@@tubeaudioslave is that motor 6374 if not which one also what’s the range you get from the batteries , been researching a lot and I think I’m gonna finally take the plunge but I’m thinking of using a 85 amp rc controller , are you still using this same set up as in video

@@ahmedsharif9400 The motor can is a Hobby King 10s sensored 5055 orange can. The controller is a 12s skateboard controller that has VESC software. I only used a 4s 8000mah to go straight up steep mtb trails. 14 miles is what I would get roughly. I recommend Molicel P42 or at least P28's to build the battery. Most Electric bikes have massive li-ion packs so take that into consideration. I made the investment in a Spot battery welder to build my own packs. Well worth it.

@@tubeaudioslave thank you very much for your wisdom very much appreciated, I have a 6374 flipsky 190 kv battle hardened got a 85a skateboard controller, I really love your simple mount and I was very confused around which battery I should get but you’ve just cleared that for me thanks a lot, also I was thinking 80100 could be a better motor for it bevoude it’s size what do you think ?

@@ahmedsharif9400 Sure no worries. Any questions during your build, just ask.

Thanks so much!

Thanks. Jack russell. Shes is nuts. Loves to play. I bought the chain drive from www.momentumboards.com/ not sure if he still makes them. If your handy scooterparts.com has the sprockets not drilled though.. and chains, Ace hardware spacers, longer hardware etc.. I bought the tires on Amazon. just search 200x50 scooter tires. you can buy packs of two with tubes for 22 bucks. My black 12amp graphenes finally died so I am battery less right now. Hopefully I will weld up the 48 Moilicels I have aquired for two 6s4p packs. I'm not liking my spot welder battery right now. I need a new car battery for it to work correctly.

Thanks, still working on it slowly.

All I did was ride it and keep it charged, keep the bearings clean and the bolts tight. Blow the board off with air once and while. I never got it wet. Probably the worst thing is to let it sit unused or over discharge the Li-ons. Its only 5000 mah gas tank unless they have changed that.. I rode the g2 blk over 1300 miles.It still has the same 14 mile range and charge time after all that. Range will vary with terrain, wind, weight, throttle use. I have since moved on to mountain boards.

ok.

I think I said it has the newer hub motor design which is more refined than the original galaxy. Less bulky on the inside area for better ground clearance. Or I was talking about changing the rear wheels. I can't remember or find it in the video. I'm a little behind with the newer backfires today. If you just bought one, just ride it, and don't mess about with it. Its a good board from the factory in my opinion.

Yes they are all available on thingyverse. Just search for Carrera slot car tracks or 1:32 size stuff. Some of the files have to be resized. Here are the lights, pitzone and fencing to get you going. I spent couple of years it felt like anyhow printing the track scenery. www.thingiverse.com/thing:2220722 www.thingiverse.com/thing:2822485 www.thingiverse.com/thing:2736785

Nice. Good luck with your build. Thanks for watching. :)

Average cruise speed probably 15-18mph. Overall speed probably 12mph. I ride full speed at 26mph for about 5-6 miles usually letting off here and there coasting which re-gens the battery a little bit. If you full throttle it on a flattish area it will deplete 5 ah (180wh) in 6.5 miles depending on your weight and wind. I can still get 12.5 miles out it on a daily basis, but any hills will quickly deplete the battery. You have to be mindful of battery juice to make it last. Its a generic battery copy of the 25r. 10s2p to make 5ah. I only ride this for enjoyment on very smooth flat bike lane which makes a big difference in performance. I never ride in eco mode ever.

Nope. Have not done anything to it. After roughly 2500 miles on a smooth bike paths its still going strong.