วีดีโอ

Locations

why couldn't you just clean it through the spark plug holes?

how many work hours is this job?

Hello, Is this things make the car long crank in the morning? Or just stop for long time , then my car will crank for long time maybe 1-2s

Its made, the task of replacing things is relatively easy... but its all the stuff you need to take off! Omg!

Hello, I have white smoke coming from the driver side similar to this description. I changed the valve cover gasket, oil filter housing, upper timing cover. What else could it be? Seems to be coming from under the catalytic converter or 02 sensor possibly? But I’m not getting codes or anything

Hello, I have a 2015 Tiguan. It cranks starts for a split second and then dies. It has spark, compression, fuel pressure at spec, no codes. It does start on starter fluid and runs for 10 seconds. I replaced fuel pump control module, drained all the fuel and replaced with new, new spark plugs, I took PCV apart and doesn't have any cracks and that other white peace is in place it feels brittle tho, timing is good. any ideas? Immo is good, no codes. its push to start and what's weird is that I need to hold button for it to crank its not enough to press it once. starts for a split second and dies.

Bro saw low oil pressure and drove it lol

How many hours lavor time

hi I'm working on 2013 boss Carrera 911s how i can do real spoiler calibration

How much does this job cost, ballpark? I have just P0491 popping up. Should I assume P0492 is next and just get both done?

Well here I am joining the rest of everyone troubled by GMs bs. I work for GM and I am not buying anymore of their garbage. I have a 2020 Acadia, just out of warranty, and this issue just started. So it seems like this issue started 2017 or earlier with their vehicles, and once again GM keeps making this crap with these bad parts. So, I'm going to get rid of this piece of crap and buy a Toyota or better. Does anyone know what the best SUV brand is out there,?

porsche cayenne 2017 same problem in 2024

2,3 cars i replced Circuit board all ok,One A7 it appear again this fault after replaced circuit board😢

HIGH MILES , JUST R&R THE HEADS HAVE THEM REBUILT ,GREAT INFO AND VIDEO >!!!!WAGENWERKS

I was driveing my car fine then didn’t drive it for two days went out side to start it just stalls unless I hit the gas now it won’t even start and it would only start I’d tap the gas now won’t even start had 9 codes got it down to 3 only have p0301 p0300 p0304 did new coil packs spark plugs air filter and something els still no start

Did you have any codes

Small zip tie would of been faster easier and saved the customer money

How many labor hours is this job? This knowledge would help me determine which shops are legitimate vs. questionable.

is there a way to fix the car without needing to do this though? Could the cat converters just be removed if that was a legal option in the country you are in? Does not fixing damage the engine in anyway? or damage the cat converters?

Just thinking out loud, but would it not be possible to just open the fog light enclosure to get to the fan, disconnect that and fill the output tube from it with de-coking spray and then air-line that in to at least partially clear the vents? That would save a LOT of work to get to them to manually declog them, wouldn't it? Question is, would it work and would it be safe on the rest of the engine?

Not enough fuel cause misfire too lean conditions. Nissan have the pump assembly in the tank with filter all related components. Intake manifold sit over the valve cover cheaply design consistently removing the 2 short bolts at the rear and the 5 at the front for repairs and maintenance.

Possible to show us on V8 4.2L Q7?

I have a 2014 s4 and these codes just popped up…what is the cost for this service?

I have the same problem p0299 and I hear a small noise from under the engine, but my car It doesn’t lose power when accelerating, do I need to change any turbo censor?

Apparently a common problem. My 2018 started right after the warranty expired.

Hi i have questions how I can do rear spoiler calibration and I'm getting code C11007

Which side would p049200 is that the driver side

Dude 😒😎 thank you 🙏 this made my day i can end the search and start the search for mechanics too replace the seal im kind of reliefed now

Thanks for your clear explanation

I have a gmc 6t75 I'm trying to replace a solenoid do you have a video on how to open these types of assemblies? I can't find any videos on anyone opening these type of tcm to replace solenoid. Please help!

Where is the parts list?

How much?

How much does this cost in a 2007 A4?

You can just not replace that and heat the wastegate flap while open and hammer it down some. Replacing the entire turbocharger is an enormous upcharge repair. Also, replacing the DV can help with this too because both the DV and WG can cause this along with several other factors relating to vacuum/boost leak..

Excellent video very informative.. Thank you! How often will a vehicle owner have to do this repair due to carbon build up ?

What a total pain in the arse job

Great video! Thanks for sharing!!

What would happen if I kept driving my Audi even if it has this problem?

I've broken so many bolts carelessly it's intimidating to dive into the engine like this...

Can you tell me what the estimated costs for this repair is?

These problem did bad cold start and hard noise from fuel pump and oil engine up and have gasoline smell and temp oil going up fast ..

Looks to me like the previous guy reused the torque to yield bolts and just cranked them in!!

Very good, really well explanada

We’re to getting fuel pressure too high dtcs with this ?

If you want to know if you have this problem in your car, simply put the car in neutral, then press the gas pedal to about 3k rpm, after that lift your foot and listen for the rattling sound with the window down. You can also hear rattle when you drive, trust me it`s really annoying...

How about blowing sea foam upper cylinder (the one you used)- through the intake hole? The one through which you pushed the boro-scope.

This is just sad. My boss and I would have never left this leave the shop like this. I would be ashamed. Trash work will come back on the "shop" that did this, or they will close. There are still shops that have integrity and care about their work. It's a source of pride in what you do.

Make sure you get a warranty the next time you buy the light from harbor freight. Damn things have bad chargers.

Well, who did that job?? They deserve to have their name exposed and published. This is what we all need to see!!!