วีดีโอ

nothing gonna fix that but rebuild!

👍

What was your strategy getting the lower passenger side bolt out. I’m stuck on that one. Won’t budge.

What was your strategy getting the lower passenger side bolt out. I’m stuck on that one. Won’t budge.

I’m about to do my 3rd oil change

Great video my dude it was fun to watch.

"waters water" what an idiot...

sick as fuck

5.4 L triton was notorious for ticking as one comment mentioned. It’s just a nature of the beast. I wouldn’t really worry about it the 4.6l also had a little tick to it. My grand Marquis ticked a little bit as well nothing to worry about and FYI, you did your oil change wrong buddy. You’re supposed to start the motor and let it run for a few minutes to make sure the oil filter collects oil then you shut it down and you check your level of oil, most oil filters hold up to 1 quart of oil just my two cents you do what you want

🤣

Is tgat a Terminator or high performance 4.6 🎉🎉🎉🎉🎉

Badass car

My issue with these ramps is that they slide on my concrete floor in my garage. I put some non slip rubber car mats under them and solved the problem. I like them alot

Is this xpipe a direct bolt on to the stock manifold? Or is there headers installed already

You’re a cool guy.

At least your mustang drives

Youre tellin me?😂

Any day you can drive your car is a good day

Fix a rod knock? Uh…. No

Lucas oil additive is total crap. And you putting on here that garbage Lucas oil will do more damage then good. All oil additives are garbage to the max.

I love my 94 Cobra

Skipped the entire installation about an install video!!! 😆

tossing the Lucas cap at the wall when the open garbage can was in frame is absolute comedic gold - thanks for the video loved every minute of it

I use lucas in every car l own.been using it 20 plus yrs.never had an oil related problem.

Your car is too nice for those wheels, especially mismatched!! Go to LMR and pick out something nice 18x10 in the rear for $6-800.

2012 VW CC 82k miles. Low oil pressure light w/ 5/30 oil. Mechanic said crankshaft bearings worn (apparently it was junk yard motor w/ big miles). He put in 5/50 and this stuff. Hot yesterday turn on engine, idle for 30 minutes, the drove for 30 minutes, may have life in this car!

Got the same shirt 👍🏾

🤦🤦🤦

4:01 "waters water" this guy definitely drinks sams club water

I can see why you used Uncle Joe as your "liberal" reference If you used a ReichWing Conservative Cult Farty-five hero like Jeebis L'orange You'd get very poor results,which is what that clown circus is well known for

Chris - great stuff - re-doing 2011 KIA Sorento - got the kit at local auto store - AND a packet of 3M Quick Headlight Clear Coat Pads - simply wipe on -

Make sure you buy the correct fuel tank. Some models had a flat style tank and others had a hump on it. The hump is the worst to have because they do not manufacture it if needed. I have the hump model and it was hell to get right.

Too painful to watch.

PB Blaster is legit. Ace hardware.

Says to use 30% if real bad so should have put half of quart more of stabilizer

Skip to 1:01 for funniest moment in the video

TAP WATER?!?!! NOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO😂😂😂😂

They have steel ones much safer than plastic since plastic for same price.

What is the drain pan/container being used at 3:40? Do you recommend it over just a typical 3-5 gallon pan and transferring oil to another container?

I buyed the weak ones works great.

Great video! Lots of helpful info. Thanks!

Do you realize an additive can’t fix mechanical damage !!!! It will only increase oil pressure and prevent dry starts , How do you expect a liquid to fix a worn or broken rod bearing or cam bearing . You guys expect too much. Use common sense 🤷‍♂️

Much better!!! Why were they silver?? Previous owner??

Would this work on low vehicles. My vehicle bumber is way low

Glad you figured it out

Did you have to cut the wheel studs in order to seat the spacer and rim flush? I had the same spacers and I ended up returning them after I wasn’t impressed with how big that gap still was and they wouldn’t seat correctly.

Mad props for trying. But your right though, satin black paint is probably the easiest.

CRP GIVEAWAY

I straigjt up finished it and plugged it back in and had it on before the video was finished. So its pretty simple guys😊

a little more complicated than i was expecting. A shopping cart got me on a windy day lol