วีดีโอ

The knob that is on the left side of the mower is the height adjustment lever knob turn it to the right to lower the mower deck as you depress the right side lever handle plus push the top of the height adjustment lever handle when you turn the knob to the left it will help raise the mower deck And lock the right side handle into the non engagement position

Love the will it run videos

What is that fuel ⛽ line you are using? I like it. Great video 📹 Also!!!!

Lol that is my dream tractor love it. Free that is a amazing thing here they from 400$-1000$ (which is why it's a dream) depending on if you want it running and moving. Or for parts.

Took me a while to watch the video. But love the detail and the fact that it’s step by step essentially. Hindsight is 20/20 but why did you do all the work on the head while it was on the floor vs on the mower? I’d think it would be easier to fasten everything other than maybe having to bend over some. Again, love the video and detail man! Great work.

Keep at it! Respectful Suggestion: Use your phone/camera to take multiple pictures at different angles to refresh your memory! Saves you from wasting your time which has value! I'll keep watching & probably suscribe! Cheers & Blessings!

To my surprise Is how the wheel on the mower came up missing.

Kubota and grasshoppers are the same mowers.

You should always put oil the filter gasket before installing it.

You should have cleaned the outside of the carb before disassembly.

There was no reason to disconnect any springs to change a pulley.

I have a 2013 base cab with the manual transmission and found a male 2 wire (blue & green) that, through another video (he did a jumper to test it), are the ones to connect to the clutch switch (cruise control), that needs to be installed where a bolt and nut are currently. The connector I mentioned is on the left side harness and is taped to it. I'll have to pull the air bag out so I can see if the wiring is there at the air bag female connector and there are 3 connections in an L shaped pattern ( top left, lower left and lower right) to the clock spring. Factory part #'s as follows: cruise switch 84632-0821, cruise switch wire 84633-04020, clutch switch 88280-14030 and cover for the switch stalk 45186-0C020-B1. Thanks for the help and wish me luck on this. I'm going to install the intermittent wiper switch and that only requires a swap out to have that feature; part #84652-02710 👍.

Check the carburetor carbulater in all your connections

Good video

👍👍

Awesome

Very good video. You were optimistic and enthusiastic throughout your entire video, which makes anyone see that they can do their own maintenance on these beasts. There aren't many videos of maintenance on these mowers. I am in the process of purchasing a 2008 with 1,750 hours. I can't wait for it to be delivered. Post more videos of any maintenance or troubleshooting you do on your mower.

It's excited to see how the chainsaw is revived. Very informative video.

It funny how many good machines I've gotten over the years that only needed simple fixes, looks like the previous owner took care of it also so thats a double win in my book

Love the videos! Keep the will it run vids coming

check the fuel pump

Hey buddy, please don't take my comment negatively, but let your dog out of the garage soon. The reverberating noise of the engine will soon kill him from stress. Dogs hear 7x louder than humans

SHOP VAC THAT CRAP OUT B4 U WASH

If it’s making a noise shut it down before you damage more items and cost more to repair Yet people still run it tell it stops and cry about the price to fix it

did he change the oil filter? ill go back and look yup he did how did I miss that lol

Podrías hacer un tutorial de cómo instalar un remote starter kit? Tanks

If you want you can use Mean Green or Greased Lightning degreaser in the ultrasonic cleaner. It works pretty good. I advice not using chem dip because it is flammable and if you heat it up you never know what might happen

Keep up the good work brother.

You should try doing an intro to your video. You just jump right into it without explaining what was going on.

You should try doing an intro to your video. You just jumped right into it without explaining what the situation was.

i bet that plastic cover does nothing, only prevents you from servicing machine :D also if you dont want rust you must add anticore or smth, as these never get any anticorosion materials under paint. problem with these are multiple, go look vintage channel similar guy in garage so he rebuilded one of these, to remove oil pump he had to dissasemble all, and on top of that 3 days trying to remove crankshaft destroyong multiple special tools little newer machine without you wont reach oil pump. what he found was inside, he had to replace ring lucky i guess, also bearings lucky it didnt had time to destroy more. All this cause no oil, while oil pump dear god he opens and inside metal casing plastic parts :DDDD gears(cogs) where all of them plastic so one destroyed itself stripped teeth, so plastic in all oil strange had no time to go to engine. so it destroyed itself and even after that cooland also shut off as its connected to same gear :D its basically made to brake

Nice video

These are interesting vehicles Capability of a 4 wheeler But yet seating capacity of a golf cart. I've seen a John Deere video Of a vehicle like this A man was working on the farm he drove it from the job site to a pub and meet some friends or family They say these are legal to be on the road The DMV Classified as tractors.

Fix one thing at a time.

You left the black protective plastic cap on the starter. That's only on there to protect it whilst in transit😂

When you get ready to sell one of these,let me know.

If that green stuff is antifreeze clean it up before your dogs get in the garage antifreeze and dogs is a deadly! combination

If everything is working correctly, the brake is locked in the on position And the PTO is disengaged. The machine will start without being on the seat.

Thank you for the content This is 1 of the 1st 0 turns they made. Is that a cemetery near your house?

Nice video I found it something to watch between Christmas and new year's.

You’re making your poor old dog nervous.

Great video, whenever I work on a carburetor I always take a pic of the carburetor linkage before disassembly this prevents a lot of frustration.

Great save!😎😎

Nice save! Keep at it. Repairs and videos will get better every time! Subscribed J.W.

The backfire is a lean condition. turn that long brass screw out. they are very touchy on the settings. The air silencer cover makes a difference on how it runs too. FWI you can just hook an external tank up to the fuel pump without having to buy the connectors, just a fuel hose and primer bulb. Let it run and warm up. that water pump did not look the best, it had some memory and should be changed. The controls have the key switch. Im assuming that was part of the cut pigtail you showed at the beginning of the video. You are going to have to buy the control box and stuff or find some parts motors and convert it to a tiller and she will sell pretty fast. That block is 100% in good condition with plenty of compression.

not to be a rude guy, you have potential, but just slow down a bit and take your time.

Thanks! My weekend project.

What size winch do you have on the trailer to pull those up ?

DID YOU EVER THINK OF VIDEOING FROM THE SIDE YOUR NOT WORKING ON. LOL

I think those are cool little vehicles.