วีดีโอ

Good Job .. But the Link to Code, there is a circuit diagram ... It does NOT have a potentiometer?!

Thank you for information 👍🔥🔥🔥

instead of power supply what can we use

bro can u make control fan using wokwi?

code and simulation link please

Dear youtuber, i did everything this video showed me but the light bulb wont turn on what could be the issue can you help me

It's a image at the link of source code in description Where is code then

how to open code. it is not opening

Thannnnnnkkk youuuu muchhh moreeee🎉

Hi Sir, I use Blynk to control the switch but I couldn't do it. Can you help to me?

it worked, thanks

Nsab

can you give the code ?

Can you give me the code?

Can you do this using pico board?

I have one question can I ask

hi please help me with this project : t seems like you are looking to create an automatic system using Arduino for controlling 2 water pumps, 2 electro vanne, and 2 water level sensors. Here is a basic outline of how you can achieve this: 1. Set up your Arduino board with the necessary components including the water pumps, float switches, water level sensors, and solenoid valves. 2. Define the connections for each component and write the code to control the system based on the inputs from the electro valv and water level sensors. 3. Implement a start button to begin the system operation. 4. When water level sensors 1 is activated, start pump 1 for 30 seconds and open electrovalve 1. 5. When water level sensors2 is activated, close electrovalve 1. 6. Once pump 1's operation time is complete, start pump 2 and open solenoid valve 2 for 10 seconds. 7. Repeat the cycle for continuous operation. Thank you

@technicalshubham I want help in a project as soon as possible How can I connect with you

sir can u make video about water control level using keypad membrane 4x4?

Heya IR Remote is not working the code given by you. can you help me sir??

hey I used your video to create a project. I miss one thing - how to protect the pump from running dry when the water runs out

thank you so much

ta på zeeeebben min please

Bhai is sure doing this code😊

strawberry jizz cake

Can we make physical too?

Acabamos de sacar 10 en un parcial por usted master se le agradece

Please send me the code

when you started the simulation , why did you remove the wire that links the power supply and the light bulb and then put it back on ? and how did you even do that because i can't modify the circuit while the simulation is still running

Sir...mera tank lenght 500mm aur 1000 ka ho toh...code me koun sa value change karna hoga?

Value of potentiometer?sir

Nice video bro❤ . Bro I need simulation video for under this topic Topic name :Automated controller of street light management systems Topic Description:Develop an automated system for real-time street light fault detection, precise location tracking, and efficient maintenance in cities.

Thank you for your step-by-step instructions. It worked for me, it just didn't seem to be connected the first time I ran the simulation, but it worked on the second run. One problem in the code: On the line //During Starting all Relays should TURN OFF digitalWrite(relay1_pin, HIGH); it should say digitalWrite(relay1_pin, LOW); The same goes for the other 3 relays. I looked at this part of the code when I noticed all relays being ON from the start.

where can I find this code?

I can't extract the code , please can you send my email id

que asombroso proyecto me gusta mucho

Bro i want ckt Diagram can you please provide it?

Thank this is my favorite video

thank you so much

Ek no bhava carry on ❤❤

great information I turned music off

How simple technique thank you sir ❤❤

Sir mene aapki video bahot dekhi he..... Bahot kuch knowledge milta he..... Main sbse request krta hu ki sab shubhamsir ko follow kro jisse aapko bhot kuch technical knowledge mil skta he

Wow........

When I copy the code from your PDF file and paste it it misses some letters. Even after I spend my time rewriting it manually it still doesn't show the time on the clock. Fix your code and don't post it in PDF format.

Works perfectly! Have to hold set button for a sec before editing. Have to do a little tweaking for breadboard usage. Great build!

Thx but the time wont change if i press the buttons. when it does want to work it goes 30 at a time. its driving me CRAZY. Please help. Thx

ling ling ling ling ade telefon berbunyi ape dalam bahaya bau bawang -irpancem

❤❤❤❤

Where's the code?