- 3
- 32 559
Friendly Finn Garage
เข้าร่วมเมื่อ 23 ส.ค. 2010
1987 Toyota Land Cruiser HJ61 Project part 2: H55F -Gearbox and transfer teardown and diagnosis!
I took apart the H55F -gearbox and transfer case of my HJ61 and found some wear. The gearbox worked ok, some minor rattle in neutral, at idle could be heard after highway drive, when the oil gets hot and thin. Some vibrations at low rpm and especially on fourth gear could be felt. It didn't pop out of gear or anything like that. 2nd and 3rd need a little attention to shift but it's more like a feature in these old boxes I think. The main reason to do this rebuild is that I want to make sure that gearbox, transfer and power take off are strong and reliable... and because I've been dreaming a long time of rebuilding a gearbox without any hurry and learning more of them :)
มุมมอง: 22 337
วีดีโอ
1987 Toyota Land Cruiser HJ61 Project Part 1: Interior and gearbox removal
มุมมอง 6K3 ปีที่แล้ว
1987 Toyota Land Cruiser HJ61 PROJECT PART 1: Interior and gearbox removal! The 61's 33 years old and has seen almost half a million kilometers so there's some rust and a bit of wear and tear. Gearbox and transfer works ok, but there's some minor noises at times, especially after long drive when oil is hot and thin. I'm gonna rebuild both of them, do a few mods, change a new heavy duty clutch, ...
1987 Toyota Land Cruiser HJ61 exhaust sound comparison! 12H-T engine sound!
มุมมอง 4.3K3 ปีที่แล้ว
Sound comparison between rusted out stock pipe with no mufflers and a huge 3.5 inch side outlet and new stock pipe with smoother bends, resonator and 2 inch side outlet. The new pipe has 59 mm(outside diameter) or 2.3 inch inlet(tube before the flexing part) and 54 mm(outside diam.) or 2.1 inch outlet(tube after the flexing part). Resonator is 41 cm or 16 inches long and has 2 inch inlet and ou...
Excellent travail j aime ça beaucoup
Je fais la mécanique automobile je besoin d'aprendre beaucoup pour l expérience
How many kms had this gearbox done? Hard life? Regular servicing? Thanks for the help
Nice video
Is there a way to inspect the clutch on the bellhousing when installed?
I think the only way to get to inspect the clutch properly is by removing the gearbox.
@@adetsalo figured so... :/
Amigo ese cabesevaca es para q motor
Great video! .. I'm waiting for the rebuild process video .. Thanks!
Hi, are you doing a rebuild video still? I found your tear down video excellent and thorough, I was really looking forward to watch reassembly video. I am soon to do a H55F rebuild and it seems everyone who does a tear down video doesn’t do the follow up for some reason?
Hi! Unfortunately I don't have time or a decent computer atm to edit more videos😐 Have fun rebuilding your H55F👍
The A440F transmission has a shim between the transmission output shaft bearing and the front cover of the Transfer case. Does the H55 set up have a shim as well?
Vuosi mennyt ja kohta vaihtuu uudelleen mutta, ei vieläkään uutta materiaalia....
i like the old tbh
Mahollisesti suomalainen?
Suomesta ollaan😊
@@adetsalo Nice. Helevetin hienoja videoita kasaat. Pistä vain lisää j60 sarjalaiseen liittyen. alan harrastajana kiinnostaa moistia katella... (Mullaki yks silleen kivasti viritetty 60. Löytyy video)
Kiitos paljon! Materiaalia on kunhan kerkiää editoida. Kattelinkin, että jotain 4wd videoo sulla oli ja paljon muuta👍 Täytyy tsekkaa se HJ-video!
Hello, I just saw your video and I have a few questions. Where can we find the front passenger seat you have. Do you have the color codes for your body paint? I find her really nice. Thank you for your feedback. Olivier from France (Toulouse)
Hello! It's an original HJ61 two passenger front seat. I hope you'll find one! I don't know the colour codes yet, but I'll have to find out them because there's some serious rust repairs going on! I'll tell you when I find out the codes. Thanks for your comment!
Really helpful video , I borrowed your idea on the DIY bearing puller hooks , I just made them heavy as possible but still able to slip behind the bearings. My first legs were too thin and bent too. Already had a hydraulic puller set so I welded these 2 legs to some 30mm square tube then the puller legs slipped in the tube. My H55F gearbox was slipping out of 5th gear . Couldn't see any wear on the synchro or teeth but later found the 5th counter gear is 2 pieces , not solid , the spline was worn between the hub and gear, pretty sure this is the problem, has a snap ring which I removed but couldn't get the hub off. Decided to clean best as possible then squirted some Loctite 680 retaining compound in the spline. It's taken up the wear slack, not sure if it will ast though. Found spline wear on the small 5th driven gear and 3rd /4th syncho hub , both just slid off the mainshaft , thought these were a press fit? Going to fit a modified long spline transfer case input gear ( spline worn again...) have to leave the PTO gear out , but I'm not planning on using it, 99% owners never use PTO I think. Waiting on bearings , gaskets etc , it's a big job.....
This is a great video for someone like me who has yet to tear down my H55F but am planning to this coming summer for new synchros and to put a low range gear set in my tcase. Also I want that PTO gearbox....
Thanks! Enjoy your H55F rebuild! PTO gearboxes don't seem to be very common.
Nice cruiser.great project. I am looking forward to seeing you make that oil pan.
Thanks Nicholas Rohland! The pan is ready and installed, lets see when I get the video done. It was pretty insane project with the tools I have, but now it done😅
Great video! however you sound very familiare to a person who plays a lot off Shen xD
Thanks C K! I had never heard of Shen before your comment. I checked it and found almost immediately a Finnish guy playing Shen and he actually did sound almost like me😄👍
@@adetsalo hahah xD. 👍
Did you need a puller to take out the front input shaft bearing?
The big bearing of input shaft wasn't very tight to get out of the case. If I remember correctly, it required only little assist of puller maybe not even that. BUT the bearing was very tight on the shaft. I don't have a press and my puller started to bend and wiggle around. I hammered it carefully but it didn't work. Finally I tig welded strenghtened puller legs to the bearing, heated the inner race carefully with tig torch not To damage the surface of the shaft and then it came out easily. 😅 Press would have been perfect.
Thanks Reto Amstad! I bought Terrain Tamer Gearbox kit and transfer case kit.
Great video! what kind of rebuild kits did you use? Thanks!
Thanks for your comment! Here In Finland most of the Hj61s have only 3 seats because of taxing. A new video of gearbox dissemble is gonna come out soon! Enjoy your 61!
God stuff. Where are you located? This HJ61 looks like a scandinavian spec (3 seats, whinch)? Best regards from a HJ61 owner from germany. :-)