วีดีโอ

Clean floor, I like the access panels .

I’m having a seizure while watching your video

Shaping up nicely

Bed liner everything

Lookin good bud. Trying to finish up outer metal on shop so can start electrical

Could do a see thru sides with lean would be cool

Those push button style would be nice for removable panels or dzus

Can you roll those lines in the cardboard first to check the fit and look? Or do the lines not stay there? It’s your car, your preference 💯

Don't forget window switches and fancy cup holders

Cool 😎 !

Looking Good I Like the Bead rolls and as you know Courtney I am Just a Plethora if mis Information But the word is STRONGR Structure Cause I cant spell RI GID I TY But Siri could

Looking good. The nutserts would probably be easier if you ever had to remove it. I got stuck on the removal of the fuel line. Over an hour and it won’t let go. But all the injectors on that side came out. So removed the clips have the last clip by the fuel line to remove. Then will try to install the injectors with the rail still attached to the line. Plugs on one side done. Will try to finish everything tomorrow but two plugs on this side will be hard by the brake booster. Engineers need to do a better job. Making general maintenance easier. I look like superman flying into an open hood just so I can reach the stuff at the back.

I like the design on the side of the tunnel!

Just remember you’re gonna have to use dynamat or some sort of material because that diesel puts off an amazing amount of heat

Yeah, that one bead roll bothered me a little bit as well. J/k ,I still like the work here. I just wish I could be there with you sometime. You wouldn't like me ,tho. I'm a hardass old biker everybody loves to laugh at but when I tell them stuff, I'm an asshole

I think, you're doing a great job. I like the flat top.

Courtney your flip car did you sell it?

It's comfort leavel that's important

you can do flat top but flat sides part way up but flat taper so 5 sided make making removable panels easier and look better than box also get sound deadner of amazon comes in a box big enough to do your job

For aesthetics, I would curve the tunnel, do it brother

When I seen the Omni I had a feeling you were in NC too. Good job!

Sound deader the heat form trans turn

That’s a lot of short cut work and slapping stuff together. Sawzaw the pipe =metal in the engine! All that did was make a salvaged truck stay salvaged

I was watching another channel I follow on bead rolling , in order to keep the panels from warping you should run them through the English Wheel only on the areas where you will bead roll. Bead rolling shrinks the metal cause it to warp also know ass ( oil canning ). The English wheel stretches the metal. You don’t need to add too much pressure on the wheel but stretch it ever so slightly. Hope this helps and I myself am not a sheet metal guy at all.

Right hand drive for steering column, like they did with the tri five chevys for the across the pond version of the American iron.

Only wear racing shoes when you drive it and maybe add a hand lever setup too if the pedal area gets tight. You just can’t sell it to a person with big feet later.

As always it is a pleasure 🙏🏾💪🏾🇺🇲✌🏾✔️👍🏾

progress is good Coming right along!

Rather than hammering up the lip on the floor pan just use a tipping die in your bead roller. Its much faster and looks a ton better.

Courtney I gotta automatic slip roll with foot pedal and jog button. But it's pretty big takes up room

Move motor back so starter will clear drop motor down thank you for video happy new year

Looking good. For the floor support by the cross member. I can see it filling up with dirt and water when the car is driving . Will need to close the holes in the middle.

Yes I was thinking a Removable Dog House Like in a Van would Be Ideal for access Looking Good More Progress

The escalades actually had special coverage on the chrome wheels because of this lol

I use my right foot for the accelerator, and my left foot for the brake in an auto. I raced sprint karts, but, was doing it long before that. I just like to cover the brake. A lot of people comment on it and tell me I'm doing it wrong, but, I think I'm one of the few doing it right lol. I like the early access, and as a member I really appreciate it. Thank you. Harper's writing is very good for her age.

Hey. I’m back looking for some input. I’m looking to make my build functional. As a jet engine technician we are always pissed at engineers. How hard would it be to remove fender bolts with the rail? Do you think the individual tabs will have the structural support to hold the hood down? Thanks

Gonna be sick, coming along quickly. Thanks for the video my friend

I'm seeing bead rolls in those panels

Coming along nicely Trans mount looks good

Hey, I am building a 48 special deluxe at the moment. Your video series has inspired me to get moving and put in work. Enjoying watching you build this car. Cheers.

Yep more progress Looking Good

Getting to the front Nice work Buddy Love it.

Question; why don't you go with a 700r4 transmission, they take up so much less real estate and you are limited!

Courtney why so heavy duty of a trans??