วีดีโอ

Will this help eliminate the pressure on the gun regulator dropping slowly to working pressure when pulling in the handle? This problem sprays out paint unevenly until it hits the working pressure.

useless expksnztion, paint societies Brain explains it better.

The perfect video in all ways, thank you.

Thanks

Use good couplers/high flow, short compressor hose the drop will reduce a lot.

Excellent. Very helpful. Thank you!

Where can i find a 1.2 gravity feed nozzle?

Exactly the demonstration I was looking for. Well done! 👍🏼👍🏼👍🏼

hello ive got the 3hp 90l only used it 3/4 times in 4yrs and stupidly used it with long cheap extention lead. it filled up ok but when i started to use it cut out and that was it NOTHING , didnt trip the house fuses ,changed plug socket fuse and tried machine DIRECT (no leads) nothing whatsoever ,tried the little red rest button on top of machine ,nothing. any advice?is there any fuses or switches inside the machine that i can try/look at. is it likely be whole new motor ??

A perfectly scripted video, not one wasted word. Very helpful.

You never said you cleaned the check valve or put a new one on

Cool pressure rig

Replaced my check valve and still have air going through to the escape valve (solonid) what to do?

Well done! Excellent presentation! Thanks for including Imperial and PSI for those of us on the other side of the pond.

Muy bien, barri la válvula con mucho ajuste, por eso la cambiare, la importo via Aliexpress, dado que en LIma no hay en el mercado. felicitaciones

Do you adjust the air pressure with the fan open or closed? because on my gun this changes the air pressure. So if i set the gun pressure to 21psi with fan open when i close the fan this increases to over 30psi! conversely if i open the fan the pressure reduces.

If only I’d watched this yesterday 😩 Great tutorial 🍻

Thank you for the detailed explanation! I had no idea how to use my new air gage at the gun so this video is very helpful!

Thanks dude, mine ended up being a broken spring in the non return valve!

What I am seeing is, when my air compressor is running, the exhaust valve is leaking. But once it shuts off, the exhaust valve stops leaking and it works normally. What could that be?

All links are DOA

Mine I think it is bad, because . I disconnected the pressure switch, and the compressor kept turning off.

Hi I have this problem on my wolf Dakota compressor which is the same design as this. I have done this twice and it has happened again. Any advice would be greatly appreciated.

Pa help naman po Kong anong dapat Kong gawin

Mayron akong nilagay na ganyan page naka off sumisingaw yong hangin anong dapat Kong gawin

Apat na wire ba ang gagamitin mga idol

My motor feed wire AND blue and brown wires were in the opposite position... So the orientation do not matter, only the correspond wire maintains the continuity of each respective circuit?

So more girth for the pressure 😁.. excellent video, thank you.

I detect the sound of a south african accent....

Why is the video so choppy?

Great video, explained simply and informatively!

I have bought 4 different regulators, convinced they were all defective, then I found this video and realized it was operator error. Thank you, as sad as it sounds, you've made my day 😄😁😃

I have a scenario where part of the air pumped on initial fill (from zero pressure till ~ 1 bar) is wasted from the control unit. Thereafter, all air goes into the tank. And there are no leaks while running or while not above this pressure. So it's not a check valve as this video is about. Do you know what this could be?

Thanks, just wanted to be sure and this was very clear, many thanks.

U just help me repair my compressor, wish I hadn't bought the pressure switch because I thought it was the issue. Thank you Thank u very much ❤

The only question I have is where to find a regulator which isn't based on a manifold made out of the cheapest alloy possible.

Great video,my compressor is blowing fuses as it start to refill,but no when the tank is empty ,i chsnged the none return valve but still the same,i noticed air leak under the pressure switch,could that be blowing the fuse ?

bonjour je vous joins mon

Excellent video. It's very informative. Many thanks for sharing.

Very well explained 😊

God bless you my friend thank yiu so much

Hello there buddy i have a Clark industrial compressor and i have bought a new motor and pump with a new check valve my compressor is not storing any compressed air in the tank can the pressure switch be at fault and i've also checked the reed valves but still nothing

Where did you get the replacement from?

I'm going to use Loctite 545 for the sealant.

Where or who made this spraid gun?.

So when it says max pressure on the side of your gun is that max inlet static pressure or working pressure? Because mine says max 43 psi but when working pressure is 29psi it jumps to 70-80 when static..

Very well explained, thank you 👍

is this what to fix when your building pressure regularly and pressure regulator is optimal but working pressure at tool fizzes out and doesnt work? even though tanks full and compressor isnt turning on.

Nicely done video. Greatly appreciated the info on curing sealant, heat to remove and time to let it set/cure after installation of parts. Cheers

If I am hearing a weird flutter noise, does that mean its a check valve?