วีดีโอ

Was that water pump making a bunch of racket like a rattle? I'm hearing a noise can't tell where it's coming from.

Man I'm about to do that now I'm stuck😢

Your video sucks!

Thank you so much!

Never seen a video that shows what you did to fix after your finished , we wanna see you fix it play by play ...

Sorry but to me the video is garbage. No idea what tools to use and direct illustration

stupid video

LMAO dude.

Mrm, by any chance, do you know where the blind spot warning sensor is. I have an idea but am not 100% sure. Thanks in advance

The code I got was p0456. My scanner reads that it's a permanent code. I read it won't erase until the cars computer acknowledges it's been fixed. Is that right or should I just clear it?

Thanks for the help

Can I get the black gasket in low’s, my toilet is Toto CST 854

I wish my ls had the thx nav

To help anyone doing this job, use a socket and tap that seal down. This will give you enough clearance for that snap ring and also break the seal, making it easier to remove. To install, tap it in far enough to clear the snap ring, install the snap ring, then use the screw to pull the seal back out to seat against the snap ring. Use a bit of PAG oil on your o-rings before installing the seal and this job will be easy.

Not enough room for a 1/4 socket I guess

Excellent video. Saved me alot of time. Anytime you can get around pulling the intake is a good day 👍👍

Gracias por tu video amigo suba más videos por favor dios lo bendiga

Is this the same way to do it on a 2010 EX35 Infiniti since they have similar engines

Wish you would of showed how you got the new snap ring in . Im bout ready to gork upmoney for new condenser with new filer already installed

Hola ,no sean egoístas ,muestren como se pone la banda del tiempo.😊

i hate that. knee deep in a beer or two, cussing at this foreign ford jaguar mess of a starter to pull out and some goober comes up to talk and wastes time.. at that point i usually just sit there under the car, take deep breaths and rethink my life decisions.

Very nice video. Clear illustrations of steps you took. Sometimes the mount has to be removed and sometimes not. I think it depends on the age of vehicle (in years) when the rubber dries out and shrinks and hardens. The Part 2 video shows more and is also good. After they fixed the initial issues with the variable valve timing, this has been an exceptionally reliable powertrain. A bitch in my opinion to work on. For so much of the stuff you really need to remove the whole thing from the car to work on it. (As the factory manual says). I like that you wore gloves a lot to keep your hands clean. I do the same thing. BTW the water pump is a lot more work.

Same issue with the 4.6 and 5.4 modular engines, 6" extension and a shallow 13mm socket always worked for me, coming in from underneath

Hello nice job. Question, someone did this for me, i guess they dropped the front of the subframe down a little like you, but strangely driving car today, it just feels different. I dunno. Does dropping the frame affect any of the front wheels, like when turning?

I repaired the computer, got new coils and plugs. Went to start it and the key won’t even turn. Have you ever ran on this problem before.

Man I did this recently and all the plastic broke off nothing to pull out it was stuck took me 2days 6+hrs total i ended up drilling a small hole then put a long 2 1/2in screw into it to grab on and wiggle out took for ever.

Como quitar el encendedor del auto buich enclave 2012

Agreed!! Gm engineers should be required to work on this shit. The wireing on this vehicle is an absolute mess!! I’ve had vehicles get me upset but I’m telling ya. I was ready to stick a rag in the tank and watch the hunk of junk burn!! Just wait until you need to pull the timing cover! Oil pan has to come off and the front axle runs right through the oil pan and is part of the front diff

Thanks !! I could not locate it !! Definitely not up front 2003 Oldsmobile brivada

Thanks boss man!

So what was the solution? Tie it to the roof?

YES ! Good video. Bottom A/C wire big problem. I broke mine crank sensor pig tail not available that I could find unless buying new harness. $$$$$. I was able to solder mine but hours of hassle. Great Video. I think some videos are same engine but in camery. Much smaller engine compartment requiring more accessories removal

where to buy this gasket and flush valve kit? I have a water leaking issue and this part is discontinue .Any information for Toto CST 862?

Thank you for making this video it saved me $$$ and saved tons of time. I had attempted to pull the alternator fuse out and ruined it. The guy at the Toyota dealer said he’d seen many in worse shape. Seems like they would have put a note in the fuse diagram that it is locked in from the bottom.

Does anybody know what screen that is? I’m trying to find one to put in

When I removed the bolts, the braket nor the fuel regulator wanted to release or wiggle. It was so attached, it was like it still had bolts attached...any advice? I really wanted to do this myself. TY

Which flapper did you use?

Do you remember your symptoms as to why you changed it? I have problem with 2nd fan not coming on, and all relays and fuses are good. Also I direct jumpered the fan motor to a 12v battery and it came on. I'm stumped.

Good video. I’m just finishing up putting the fuel rail back and now looking at reinstalling the intake. To be honest, taking it out was a bear, AC line in the way had to be gently tweaked a bit with much frustration. I noticed you made no note of alternator removal. That too was tough as the lowest bolt backed up into the AC line trapping my ratchet box wrench and the mistake was time consuming, a mistake my mechanic brother warned me about. For those interested in ratcheting box wrenches be sure to get the finger lever reversible set.

I did from the top easy in 5 mins

Also, these are known to leak fuel. Mine is an '04 and leaks intermittently. I can occasionally smell fuel and after checking under the hood, found a slight leak at this regulator. I've seen videos of these TB's and Envoys burning up so, new regulator inbound.

Atlas is a good strong engine..but anything that you have to do to work on it becomes a real pain in the ass...

Thanks. Because it sure wasn't up front. 😂

So Toyota messed up my radiator & they offered to replace it. I have an 03 Corolla with 150,000 miles. Don’t I have to replace the water pump & thermostat when replacing the radiator?

Did this cause all the electrical dashboard, breaks, power windows and all not to work?

PLEASE how do you get that screw on the right side in the glove box i just can’t get it

Skips 90% of the job lol

You never said if that fixed your issue. Was the manifold leaking too?

Do you think this could fix a "running rough" issue? Mine sat for a month with 1/2 tank of gas. Started it and no issues then 30 min later started idling rough and stalled. Started it back up and it just runs louder and rough as if moisture or something is in the lines or bad gas. Any ideas? I'm a musician not a mechanic.

My car isn't running hot but resaroe is bubbling