Thank you for the teaching, as regards the machining of parts very well, but with welding, the current passes through the bearings melting the seals of the same, I believe the welding can be done outside the assembly, greetings!
I been welding and fabricating for years and I found that the twists from a drill press can be very hot and very sharp, he seemed to handle it well by wearing gloves w/ silicone bumps. It is his shop so he can do whatever he wants.
What you're forgetting is a lot of folks more amateur than him will watch these videos and think her's doing it all correctly, everyone posting has a duty to show the safe way to do something, far too many downright dangerous or just plain wrong things are seen on YT.
Best comment on this video! It’s HIS shop! He can drill naked if he wants to! Don’t advise welding that way though! Worst job in the world is running the welding shop at the nudist colony! Ha!
I know this question may have already been asked, but did you make the rollers or did you buy them? If you bought the rollers, where did you buy them? Thanks.
One of the most important tools in every shop is cutting oil. Try it sometime. It’s cheaper than constantly wearing out your drills, and particularly, your taps. The problem is that you need an entirely new tool for another size.
Nice job, You should never wear glove on a drill press, if a piece off metal gets in your glove, it can pull your hand to the drill bit and rip some skin off.
Drill presses aren't lathes. You can wear gloves no problem. I'd rather wear gloves than get whipped by metal shavings and steel pieces flying without gloves. Been using drill press for many years and never happened like what you are thinking. But if it was a mill or lathe then yes no loose clothing.
Your 100% correct just because someone has been doing it for years doesn't mean its correct. He should be using a clamp also. That piece moves and that glove gets caught it will pull your hand in and break it and tear it up depending on the drive for the drill press.
Information that would be useful to someone like me:1) dimensions of raw materials?2) pulleys obtained where?3) distance from center of pulley bearing to center of drilled holes?4) diameter of drilled thru holes?5) diameter and drill depth of countersink drill?6) length/thread pitch of allen head bolts that fasten pulley to raw material?7) diameter and hole location on small rectangular piece?8) and a myriad of other dimensions that seem to be done by eyeballing only...So...do I just guess at all of the above stuff?
Thank you for not showing us 15 min of how you cleaned material with a grinder. I haven’t been very good about using drill press stop so don’t feel so bad. Now that I have a mill I have decided I like my fingers. Like the video!
Good for a quick job needed for only one size of bend. Take this the next steps with removable pulleys so that other radii and tubing sizes will work. Manual hole location performed was below shop standards, but simply to crank out a few needed bends, not a problem. Welding with the pulleys in place probably overheated the bearings. It is well to do all welds away from heat sensitive parts. Other safety related remarks below are noted and won't be repeated. A tool of this type saves big amounts of money and problems when only a very exact fit of transfer pipes will be acceptable.
gloves are NOT your friend in drilling / milling etc you will drill a hole in your hand if it tangles bad. this is a really good concept though on the design.
Great idea and great video, but thank goodness for the mute button. Would be better without the endlessly repetitive thump, thump, thump, in the background.
Also.... Dude, cutting fluid will help you loads as will buying some form of clamp and please no gloves. When working with power tools. Like drills and grinders, don't want to see you maimed.
I'd like to know where you got those nice pulleys/mandrels. Those are sweet! Also...I would have welded the handle in a straight line to the bending force rather than at an angle.
Do not wear gloves, rings, watches, or bracelets while working with a drill press... unless your protesting then all common sense goes out the window. (& maybe just maybe ground on the side with the weld and not through the bearings.) Great design by the way!!!
I noticed that you were wearing gloves while operating the drill press, so I feel compelled to tell you that you shouldn't run with scissors or swim within 30 minutes of eating!
Hello Just today i make that one bending machine i use 2 sames bearings rolls U Φ 90mm and biggest flange because i want to turn hudraulic pipes Φ12mm max 330 bar pressure .So when i finished the bending machine i try to turn masif stainless steel Φ12 mm it's so easy and amazing work looks like factory work, (i turn the masif steel up to 280 degrees) i safe lot of money up to 350€ for a buy bending machine. The cost it was only 25 € to make that bending machine. Thanks a lot for your idea!!!! Best regards !!!! Leonidas greece
Hi, it's a great review you are leaving here. Where did you buy your bearing rolls ? I want to bend 4 stainless tubes of 32mm diameter to build a motorcycle downpipes. Thanks brother
You could anneal that copper before bending it so it bends better and doesnt get flat spots. Refridgeration tube also bends better than standard copper tube.
My god, lock your vise so it’s not turning so freely. ( sorry I couldn’t find anything else to bitch about... all the good stuff was taken) lol good job on the jig though!
the sand trick does not prevent tube deformation, just reduces it. If you need a good looking job you need a tubing die or a very close approximation. When I needed the best looking job i could get I used conduit and a conduit bender, or as close as I could get and inserted a dowel close to the inside diameter of the tube sawed at intervals so it would crack at the cuts and pushed it to where the bend was going to be and that prevented most of the deforming. Knockoff benders aren't too expensive if you are going to do a lot of bending of the same diameter tube.
Where did you get the ready made rolls. Please remove your gloves when operating machinery, I have seen too many ripped and torn fingers when the drill bit grabs them.
Don't really know since it's not my project. I have some bending jigs I made for solid stock just using pipe or steel rod , you would get different bends with different widths of pipe and different spacing. You can also have the gap be for the diameter of what your bending. I would just try a few sizes apart, kinda eye balling what he did here or I'm sure can find other posts on this. If I was gonna build one I'd make it adjustable. Hope this helps, good luck!
Flat spots could have been avoided if the main die wasn't fixed. It needs a clamp to hold the material that he's bending and with the main roller free, the tube would conform to the round shape easier.
NEXT TIME YOU DO A VIDEO PLEASE SHOW US THE FINISHED PRODUCT AND WHAT IT CAN DO..... THEN SHOW THE STEPS IT TAKES TO PRODUCE THE PARTS......PRODUCT FIRST FINISHED.....THEN THE CONSTRUCTION DETAILS, IF THE VIEWER HAS AN INTEREST.....PAST THAT COMPLIMENTS FOR YOUR ACCOMPLISHMENTS..................VIEWER THOUGHTS????????????????????????????????? THE VIEWERS ALSO CAUTION NO CLOVES WITH THE DRILL PRESS.....IN YOUR INTEREST....
Hi, I have no skills or tools. However, there is a desire to bend OD14mm stainless steel pipes neatly. Is it possible to create one if you like? I want to be able to bend as easily as possible because I have no power at the age of 60. Please reply if possible.
Now that’s 1 of the simplest tubing benders that I have seen, thanks for sharing your thoughts and video
Thank you for the teaching, as regards the machining of parts very well, but with welding, the current passes through the bearings melting the seals of the same, I believe the welding can be done outside the assembly, greetings!
The current passes through the bearings melting the seals , or the heat from the weld?
th-cam.com/video/Yt3mK2Vg8WI/w-d-xo.html
Nice idea, I would suggest using some sort of oil when drilling steel. Your drill bits will last a lot longer
I been welding and fabricating for years and I found that the twists from a drill press can be very hot and very sharp, he seemed to handle it well by wearing gloves w/ silicone bumps. It is his shop so he can do whatever he wants.
You mean stringy chips.
Bảo nhiêu tiền bỏ uống the
Hjsieii4
What you're forgetting is a lot of folks more amateur than him will watch these videos and think her's doing it all correctly, everyone posting has a duty to show the safe way to do something, far too many downright dangerous or just plain wrong things are seen on YT.
Best comment on this video! It’s HIS shop! He can drill naked if he wants to! Don’t advise welding that way though! Worst job in the world is running the welding shop at the nudist colony! Ha!
Can we get a source for the dies/mandrels please and some dimensions, would love. To build one.
I know this question may have already been asked, but did you make the rollers or did you buy them? If you bought the rollers, where did you buy them? Thanks.
i want to know this also!
Great job. Find yourself some milling machine work holding clamps, your drill press has the channels to slide them in.
Молодец, хорошая работа. Но перчатки надо снять при работе со сверлильным станком!
2 God sar
Nice tools if portability so good
Great job
Hope the pulleys are interchangeable to accommodate various sizes of tubings.
I read a comment once that said it's bad to wear gloves when using a drill press.
Jeremy can loose a finger quite easily, anyone with half a brain would have a vies on their drill press
One of the most important tools in every shop is cutting oil. Try it sometime. It’s cheaper than constantly wearing out your drills, and particularly, your taps.
The problem is that you need an entirely new tool for another size.
Nice job, You should never wear glove on a drill press, if a piece off metal gets in your glove, it can pull your hand to the drill bit and rip some skin off.
Drill presses aren't lathes. You can wear gloves no problem. I'd rather wear gloves than get whipped by metal shavings and steel pieces flying without gloves. Been using drill press for many years and never happened like what you are thinking. But if it was a mill or lathe then yes no loose clothing.
Peut on avoir de stage avec vous ? Je suis intéressé .
Your 100% correct just because someone has been doing it for years doesn't mean its correct. He should be using a clamp also. That piece moves and that glove gets caught it will pull your hand in and break it and tear it up depending on the drive for the drill press.
Yeah verry nice
100 % I agree with you.
better leverage if you would keep your handle inline instead of angled up jmo.
Crazy wearing gloves w a drill press.
Information that would be useful to someone like me:1) dimensions of raw materials?2) pulleys obtained where?3) distance from center of pulley bearing to center of drilled holes?4) diameter of drilled thru holes?5) diameter and drill depth of countersink drill?6) length/thread pitch of allen head bolts that fasten pulley to raw material?7) diameter and hole location on small rectangular piece?8) and a myriad of other dimensions that seem to be done by eyeballing only...So...do I just guess at all of the above stuff?
just made bending jig as per your video, works great thanks
Thank you for not showing us 15 min of how you cleaned material with a grinder. I haven’t been very good about using drill press stop so don’t feel so bad. Now that I have a mill I have decided I like my fingers. Like the video!
Excellent! Now build a machine based on that concept that will make copper coils!
copper coils are easy.
Can i bend ss pipe 202
Good
Good for a quick job needed for only one size of bend. Take this the next steps with removable pulleys so that other radii and tubing sizes will work. Manual hole location performed was below shop standards, but simply to crank out a few needed bends, not a problem. Welding with the pulleys in place probably overheated the bearings. It is well to do all welds away from heat sensitive parts. Other safety related remarks below are noted and won't be repeated. A tool of this type saves big amounts of money and problems when only a very exact fit of transfer pipes will be acceptable.
Buena Idea y fácil. gracias.
Hats off to you Sir! It would have been really a loss for me if I had never came across this video.
Would be great if you Add a list of material on description, atleast pulley dimensions... BTW great work, keep going!
that "music" is horrible, the content is good!
gloves are NOT your friend in drilling / milling etc you will drill a hole in your hand if it tangles bad. this is a really good concept though on the design.
You shouldn't wear gloves at the drill press just clamp your part in place
Was just going to say this. NO gloves around rotating equipment.
Julie Waite hey I don't wear under wear at the drill press hehe
Excellent idea
Great machine! I will do it myself. Thank you!
Great idea and great video, but thank goodness for the mute button. Would be better without the endlessly repetitive thump, thump, thump, in the background.
круто молодец👍👍👍👍
Also.... Dude, cutting fluid will help you loads as will buying some form of clamp and please no gloves. When working with power tools. Like drills and grinders, don't want to see you maimed.
th-cam.com/video/Yt3mK2Vg8WI/w-d-xo.html
Your idea is good..💯👍👍👍👏👏🤝
La mejor dobladora y sencillo de hacerlo gracias por compartir 🇦🇷saludos punta alta Bs.As. Argentina 🇦🇷
Excellent idea.
Simple and smart.
I'd like to know where you got those nice pulleys/mandrels. Those are sweet! Also...I would have welded the handle in a straight line to the bending force rather than at an angle.
👍
@@asasmohamed6986
DIGO SIMPLESMENTE FORMIDÁVEL ... JAÚ SP 🇧🇷👍 ABRAÇOS 👍🙏
Espectacular...felicitaciones...gracias.
Do not wear gloves, rings, watches, or bracelets while working with a drill press... unless your protesting then all common sense goes out the window. (& maybe just maybe ground on the side with the weld and not through the bearings.) Great design by the way!!!
that first rule pretty much applies to all power tools.
good video and good machines
સરસ
I noticed that you were wearing gloves while operating the drill press, so I feel compelled to tell you that you shouldn't run with scissors or swim within 30 minutes of eating!
Gracias es muy funcioal te deo muchas bendiciones.
Outstanding idea. Thank you for sharing
Hello, nice idea
Could this be a successful idea in a 22mm tube?
Good work
pwede gayahim
Parabéns ótimo trabalho 👍
Prático e fácil de fazer,,
👌👌👏👏👍👍
th-cam.com/video/Yt3mK2Vg8WI/w-d-xo.html
Hello Just today i make that one bending machine i use 2 sames bearings rolls U Φ 90mm and biggest flange because i want to turn hudraulic pipes Φ12mm max 330 bar pressure .So when i finished the bending machine i try to turn masif stainless steel Φ12 mm it's so easy and amazing work looks like factory work, (i turn the masif steel up to 280 degrees) i safe lot of money up to 350€ for a buy bending machine. The cost it was only 25 € to make that bending machine.
Thanks a lot for your idea!!!!
Best regards !!!! Leonidas greece
Hi, it's a great review you are leaving here.
Where did you buy your bearing rolls ? I want to bend 4 stainless tubes of 32mm diameter to build a motorcycle downpipes.
Thanks brother
Can you published the material list
Nice design and build it looks like it works pretty well
Super
Never wear gloves working on any spinning machinery !!,
why is that? serious question, i do it always
gloves with machinery = BAD IDEA! (unless of course you don't mind all that goes with getting them ripped from what is currently your hand)
and use cutting oil.
Also clamp what u are drilling
Good video, where did you buy the pulleys? Be nice if everyone left links.
Brilliant now to upscale for 2" DOM...
Dude, never wearing glows while you are drilling, workers safety is very important.
You could anneal that copper before bending it so it bends better and doesnt get flat spots. Refridgeration tube also bends better than standard copper tube.
Thank you
What type of welding is that
Excelente en la materia
You keep linking a TH-cam video but where did you buy the pilots? Is there an actually site link or amazon?
A waste of time if you don't tell where to get the parts, specifically the machined rollers.
th-cam.com/video/Yt3mK2Vg8WI/w-d-xo.html
Nice. But whare did you get the wheels?
Good 👍👍👍👍👍
Good 👍
My friend
Super👌👌👌👌👌
Good video
what brand of cut off wheel is that yellow one ur using on ur angle grinder?
wow.... i like it so much...
DO YOU THINK POSSIBLE TO FOLD 7/8 DIAMETER ALUMINUM TUBE WITH 1.2 MM THICK WALL WITH THAT TYPE OF FOLDER
i like the concept. learned from it
I'm so impressed to see this concept Be blessed
Buy a set of pipe benders that will cover 22mm and 15mm. Much easier and cheaper.
Bom dia, muito Boa esta maquina,já vi uma parecida mas, com regulagens para vira tudos com outros diâmetros...
Beautiful well done.
What welder are you using?
Welter mig
pulley source link - please and thank you
McMaster-Carr has the exact same ones. Not sure if thats where he got his though.
th-cam.com/video/l9JKQq0vGYc/w-d-xo.html
@@taylorjams4845 .7
My god, lock your vise so it’s not turning so freely. ( sorry I couldn’t find anything else to bitch about... all the good stuff was taken) lol good job on the jig though!
Espectacular quiero una quien las hace
If you were to fill tube with sand it would not crush on the back side.
the sand trick does not prevent tube deformation, just reduces it. If you need a good looking job you need a tubing die or a very close approximation. When I needed the best looking job i could get I used conduit and a conduit bender, or as close as I could get and inserted a dowel close to the inside diameter of the tube sawed at intervals so it would crack at the cuts and pushed it to where the bend was going to be and that prevented most of the deforming. Knockoff benders aren't too expensive if you are going to do a lot of bending of the same diameter tube.
ADW Designs you can fit a proper spring coil that is designed to fit up inside the copper pipe. A lot of plumbers us this system a lot.
Hello sir,. Can we bend steel pipes also with this machine.
I'm also be interested this question.
Not without a hell of a strong handle and something to hold it better than a vise with loose jaws..
Heat it up
Please check the link uniflex bending machine made in germeny if u don't get it contact to me
th-cam.com/video/l9JKQq0vGYc/w-d-xo.html
Superb
Where did you get the ready made rolls. Please remove your gloves when operating machinery, I have seen too many ripped and torn fingers when the drill bit grabs them.
You can get pulley wheels at Surplus Center
Bull Mtn. Billy could you give me a description about the two pulley wheels’ size? diameters for example?
Don't really know since it's not my project. I have some bending jigs I made for solid stock just using pipe or steel rod , you would get different bends with different widths of pipe and different spacing. You can also have the gap be for the diameter of what your bending. I would just try a few sizes apart, kinda eye balling what he did here or I'm sure can find other posts on this. If I was gonna build one I'd make it adjustable. Hope this helps, good luck!
th-cam.com/video/l9JKQq0vGYc/w-d-xo.html
Cool invention, though I wouldnt use that for pipes in installations, looking at the constrictions it produces 9:25
Great jobb!
what is the brand of your mig machine sir?
You should always wear gloves while boring holes on a drill press.
NEVER wear gloves when operating a drill press! I had a worker lose a finger when his glove got caught by the drill bit! Very unsafe practice!
Is welding close to bearings a good idea.?
Irrelevant in this application
Flat spots on bending and why are you using an angle on your bending arm?
Flat spots could have been avoided if the main die wasn't fixed. It needs a clamp to hold the material that he's bending and with the main roller free, the tube would conform to the round shape easier.
@@joelclear1578 so are you saying he should have used a broken main die ?
Astoundin !
Parabéns amigo muito bom o projeto parabéns mais uma vez
NEXT TIME YOU DO A VIDEO PLEASE SHOW US THE FINISHED PRODUCT AND WHAT IT CAN DO.....
THEN SHOW THE STEPS IT TAKES TO PRODUCE THE PARTS......PRODUCT FIRST FINISHED.....THEN THE CONSTRUCTION DETAILS, IF THE VIEWER HAS AN INTEREST.....PAST THAT COMPLIMENTS FOR YOUR ACCOMPLISHMENTS..................VIEWER THOUGHTS????????????????????????????????? THE VIEWERS ALSO CAUTION NO CLOVES WITH THE DRILL PRESS.....IN YOUR INTEREST....
Đơn giản nhỉ. Chỉ tiếc không thau đổi được ống có tiết diện khác
Jos mantap mas bro 👍👍
Where did you get your dies from. Without a lathe or mill how do you get the dies?
Hi, I have no skills or tools. However, there is a desire to bend OD14mm stainless steel pipes neatly. Is it possible to create one if you like? I want to be able to bend as easily as possible because I have no power at the age of 60.
Please reply if possible.
Good job
En tubo de cobre no hay problema, pero en tubo de acero se aplasta.
for DIY Usfull idia pwede b magpagawa ng 2 roller para sa manual pipe bender 1pcs3/4*2 1pcs1/2*2
Sq. Bar sida karne ka idea batao taki kaam jaldi ho sake.
C'est magnifique depuis bénin
Sencillo práctico y efectivo a copiar uno que funcione con tuvo emt gracias...
When mig welding you should push rather than pull, the welds are stronger.